2011-2013 Land Cruiser · Service Manual Vehicle Interior

Glass Breakage Sensor Circuit

Circuit diagnosis · Vehicles built from Sep 2011

DESCRIPTION

When the glass breakage sensor detects that the back door glass, quarter window glass LH or quarter window glass RH is tapped or broken, the sensor will set off the alarm for 30 seconds.

WIRING DIAGRAM

B190851E01

INSPECTION PROCEDURE


1. READ VALUE USING INTELLIGENT TESTER (GLASS BREAK SENSOR)
  1. Using the intelligent tester, read the Data List.

    Entry&Start 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Glass break sensor detection
    Glass breakage sensor detection / ON or OFF
    ON: Glass breakage sensor operates
    OFF: Glass breakage sensor does not operate
    -

    OK:
    ON (glass breakage sensor operates) appears on screen.



NG
Go to step 2
OK

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

2. INSPECT CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

  1. B188312E01
    Disconnect the E30 ECU connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    E30-23 (GBS) - Body ground
    Always
    Below 1.5 V



NG
REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)
OK


3. CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU [SMART KEY ECU ASSEMBLY] - GLASS BREAKAGE SENSOR)

  1. Disconnect the E30 ECU connector.B188315E01

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    E30-23 (GBS) - L34-2 (SSR+)
    Always
    Below 1 Ω
    L34-1 (SSR-) - K26-2 (SSR+)
    Always
    Below 1 Ω
    K26-1 (SSR-) - S10-1 (SSR+)
    Always
    Below 1 Ω
    S18-1 (E) - Body ground
    Always
    Below 1 Ω



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


4. INSPECT QUARTER WINDOW GLASS RH

  1. B189175E01
    Disconnect the L34 sensor connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    1 (SSR-) - 2 (SSR+)
    Always
    Below 1 Ω



NG
REPLACE REAR DOOR QUARTER WINDOW GLASS RH
OK


5. INSPECT QUARTER WINDOW GLASS LH

  1. B189175E02
    Disconnect the K26 sensor connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    1 (SSR-) - 2 (SSR+)
    Always
    Below 1 Ω



NG
REPLACE REAR DOOR QUARTER WINDOW GLASS LH
OK


6. INSPECT BACK DOOR GLASS

  1. B189433E01
    Disconnect the S10 sensor connector.

  1. Disconnect the S18 defogger connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    S10-1 (SSR+) - S18-1 (E)
    Always
    Below 1 Ω



NG
REPLACE BACK DOOR GLASS
OK

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)


← Security Indicator Light Circuit (from Jan 2012)Certification ECU Power Source Circuit (Sep 2011 – Dec 2011) →