2011-2013 Land Cruiser · Service Manual Vehicle Interior

B1422/22 Compressor Lock Sensor Circuit

Diagnostic trouble codes · Vehicles built from Jan 2012

Versions by build date: Sep 2011 – Dec 2011 from Jan 2012

SYSTEM DESCRIPTION

The ECM sends the engine speed signal to the air conditioning amplifier assembly via CAN communication.
The air conditioning amplifier assembly reads the difference between compressor speed and engine speed. When the difference becomes too large, the air conditioning amplifier assembly determines that the compressor is locked, and turns the magnetic clutch off.
DTC Code
DTC Detection Condition
Trouble Area
B1422/22
An open or short in the compressor lock sensor circuit.
  1. Cooler compressor assembly (A/C lock sensor)
  2. Compressor drive belt
  3. Harness or connector between cooler compressor assembly and air conditioning amplifier assembly
  4. Air conditioning amplifier assembly
  5. CAN communication line

WIRING DIAGRAM

E160580E05
E160580E06

INSPECTION PROCEDURE


1. CHECK CAN COMMUNICATION SYSTEM
  1. Use the intelligent tester to check if the CAN communication system is functioning normally.

    Result 
    Result
    Proceed to
    CAN DTC is not output
    A
    CAN DTC is output (for LHD)
    B
    CAN DTC is output (for RHD)
    C



B
GO TO CAN COMMUNICATION SYSTEM (Click here)

C
GO TO CAN COMMUNICATION SYSTEM (Click here)
A


2. INSPECT AIR CONDITIONING AMPLIFIER ASSEMBLY

  1. E156758E04
    w/ Rear Heater
    1. Remove the air conditioning amplifier assembly with its connectors still connected (Click here).

    2. E157042E01
      Measure the waveform of the connector.
      Measurement Condition 
      Item
      Contents
      Terminal No. (Symbol)
      E35-28 (LOCK) - E35-29 (SG-5)
      Tool Setting
      200 mV/DIV., 10 ms/DIV.
      Condition
      Engine running
      A/C switch on
      Blower switch LO

  1. E160329E02
    w/o Rear Heater
    1. Remove the air conditioning amplifier assembly with its connectors still connected (Click here).

    2. E157042E01
      Measure the waveform of the connector.
      Measurement Condition 
      Item
      Contents
      Terminal No. (Symbol)
      E81-8 (LOCK) - E81-35 (SG-5)
      Tool Setting
      200 mV/DIV., 10 ms/DIV.
      Condition
      Engine running
      A/C switch on
      Blower switch LO



NG
Go to step 3
OK

REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY (Click here)

3. INSPECT COOLER COMPRESSOR ASSEMBLY (A/C LOCK SENSOR)

  1. E160865E02
    Disconnect the C30 connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    C30-1 (SSR+) - C30-2 (SSR-)
    20°C (68°F)
    65 to 125 Ω



NG
REPLACE COOLER COMPRESSOR ASSEMBLY (A/C LOCK SENSOR)
OK


4. CHECK HARNESS AND CONNECTOR (AIR CONDITIONING AMPLIFIER - A/C LOCK SENSOR)

  1. E156712E02
    w/ Rear Heater
    1. Disconnect the E35 amplifier connector.

    2. Disconnect the C30 compressor connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      E35-28 (LOCK) - C30-1 (SSR+)
      Always
      Below 1 Ω
      E35-29 (SG-5) - C30-2 (SSR-)
      Always
      Below 1 Ω
      E35-28 (LOCK) - Body ground
      Always
      10 kΩ or higher
      E35-29 (SG-5) - Body ground
      Always
      10 kΩ or higher

  1. E160330E01
    w/o Rear Heater
    1. Disconnect the E81 amplifier connector.

    2. Disconnect the C30 compressor connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      E81-8 (LOCK) - C30-1 (SSR+)
      Always
      Below 1 Ω
      E81-35 (SG-5) - C30-2 (SSR-)
      Always
      Below 1 Ω
      E81-8 (LOCK) - Body ground
      Always
      10 kΩ or higher
      E81-35 (SG-5) - Body ground
      Always
      10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY (Click here)


← B1422/22 Compressor Lock Sensor Circuit (Sep 2011 – Dec 2011)B1423/23 Pressure Sensor Circuit (Sep 2011 – Dec 2011) →