B1422/22 Compressor Lock Sensor Circuit
Diagnostic trouble codes · Vehicles built Sep 2011 – Dec 2011
Versions by build date: Sep 2011 – Dec 2011 from Jan 2012
SYSTEM DESCRIPTION
The ECM sends the engine speed signal to the air conditioning amplifier assembly via CAN communication.The air conditioning amplifier assembly reads the difference between compressor speed and engine speed. When the difference becomes too large, the air conditioning amplifier assembly determines that the compressor is locked, and turns the magnetic clutch off.
| DTC Code |
DTC Detection Condition |
Trouble Area |
| B1422/22 |
An open or short in the compressor lock sensor circuit. |
|
WIRING DIAGRAM




INSPECTION PROCEDURE
| 1. CHECK CAN COMMUNICATION SYSTEM |
Use the intelligent tester to check if the CAN communication system is functioning normally.
Result Result
Proceed to
CAN DTC is not output
A
CAN DTC is output (for LHD)
B
CAN DTC is output (for RHD)
C
|
|
||||
|
|
||||
| A | |
| 2. INSPECT AIR CONDITIONING AMPLIFIER ASSEMBLY |
w/ Rear Heater

Remove the air conditioning amplifier assembly with its connectors still connected (Click here).
Measure the waveform of the connector.

Measurement Condition Item
Contents
Terminal No. (Symbol)
E35-28 (LOCK) - E35-29 (SG-5)
Tool Setting
200 mV/DIV., 10 ms/DIV.
Condition
Engine running
A/C switch on
Blower switch LO
w/o Rear Heater

Remove the air conditioning amplifier assembly with its connectors still connected (Click here).
Measure the waveform of the connector.

Measurement Condition Item
Contents
Terminal No. (Symbol)
E81-8 (LOCK) - E81-35 (SG-5)
Tool Setting
200 mV/DIV., 10 ms/DIV.
Condition
Engine running
A/C switch on
Blower switch LO
|
|
||||
| OK | ||
| ||
| 3. INSPECT COOLER COMPRESSOR ASSEMBLY (A/C LOCK SENSOR) |
Disconnect the C30 connector.

Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Condition
Specified Condition
C30-1 (SSR+) - C30-2 (SSR-)
20°C (68°F)
65 to 125 Ω
|
|
||||
| OK | |
| 4. CHECK HARNESS AND CONNECTOR (AIR CONDITIONING AMPLIFIER - A/C LOCK SENSOR) |
w/ Rear Heater

Disconnect the E35 amplifier connector.
Disconnect the C30 compressor connector.
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Condition
Specified Condition
E35-28 (LOCK) - C30-1 (SSR+)
Always
Below 1 Ω
E35-29 (SG-5) - C30-2 (SSR-)
Always
Below 1 Ω
E35-28 (LOCK) - Body ground
Always
10 kΩ or higher
E35-29 (SG-5) - Body ground
Always
10 kΩ or higher
w/o Rear Heater

Disconnect the E81 amplifier connector.
Disconnect the C30 compressor connector.
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Condition
Specified Condition
E81-8 (LOCK) - C30-1 (SSR+)
Always
Below 1 Ω
E81-35 (SG-5) - C30-2 (SSR-)
Always
Below 1 Ω
E81-8 (LOCK) - Body ground
Always
10 kΩ or higher
E81-35 (SG-5) - Body ground
Always
10 kΩ or higher
|
|
||||
| OK | ||
| ||
