2011-2013 Land Cruiser · Service Manual Vehicle Exterior

TERMINALS OF ECU

System information · Vehicles built from Sep 2011


CHECK FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY LH
B158006E17
  1. Disconnect the I12 motor connector.

  2. Measure the resistance and voltage according to the value(s) in the table below.

    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    I12-2 (B) - I12-1 (GND)
    L - W-B
    Battery power supply
    Always
    11 to 14 V
    I12-1 (GND) - Body ground
    W-B - Body ground
    Ground
    Always
    Below 1 Ω
    If the result is not as specified, there may be a malfunction on the wire harness side.

  3. Reconnect the I12 motor connector.

  4. Measure the voltage according to the value(s) in the table below.

    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    I12-10 (UP) - I12-1 (GND)
    L - W-B
    Power window up operation
    Ignition switch ON, multiplex network master switch off → up
    11 to 14 V → Below 1 V
    I12-10 (UP) - I12-1 (GND)
    L - W-B
    Power window up operation
    Ignition switch ON, door glass fully open → power window auto up operation → door glass fully closed
    11 to 14 V → Below 1 V → 11 to 14 V
    I12-7 (DOWN) - I12-1 (GND)
    B - W-B
    Power window down operation
    Ignition switch ON, multiplex network master switch off → down
    11 to 14 V → Below 1 V
    I12-7 (DOWN) - I12-1 (GND)
    B - W-B
    Power window down operation
    Ignition switch ON, door glass fully closed → power window auto down operation → door glass fully open
    11 to 14 V → Below 1 V → 11 to 14 V
    If the result is not as specified, the motor may be malfunctioning.


CHECK FRONT POWER WINDOW REGULATOR MOTOR RH
B158006E18
  1. Disconnect the I4 motor connector.

  2. Measure the resistance and voltage according to the value(s) in the table below.

    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    I4-2 (B) - I4-1 (GND)
    L - W-B
    Battery power supply
    Always
    11 to 14 V
    I4-1 (GND) - Body ground
    W-B - Body ground
    Ground
    Always
    Below 1 Ω
    If the result is not as specified, there may be a malfunction on the wire harness side.

  3. Reconnect the I4 motor connector.

  4. Measure the voltage according to the value(s) in the table below.

    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    I4-10 (UP) - I4-1 (GND)
    L - W-B
    Power window up operation
    Ignition switch ON, power window regulator switch off → up
    11 to 14 V → Below 1 V
    I4-10 (UP) - I4-1 (GND)
    L - W-B
    Power window up operation
    Ignition switch ON, door glass fully open → power window auto up operation → door glass fully closed
    11 to 14 V → Below 1 V → 11 to 14 V
    I4-7 (DOWN) - I4-1 (GND)
    B - W-B
    Power window down operation
    Ignition switch ON, power window regulator switch off → down
    11 to 14 V → Below 1 V
    I4-7 (DOWN) - I4-1 (GND)
    B - W-B
    Power window down operation
    Ignition switch ON, door glass fully closed → power window auto down operation → door glass fully open
    11 to 14 V → Below 1 V → 11 to 14 V
    If the result is not as specified, the motor may be malfunctioning.


CHECK REAR POWER WINDOW REGULATOR MOTOR LH
B158006E19
  1. Disconnect the J11 motor connector.

  2. Measure the resistance and voltage according to the value(s) in the table below.

    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    J11-2 (B) - J11-1 (GND)
    L - W-B
    Battery power supply
    Always
    11 to 14 V
    J11-1 (GND) - Body ground
    W-B - Body ground
    Ground
    Always
    Below 1 Ω
    If the result is not as specified, there may be a malfunction on the wire harness side.

  3. Reconnect the J11 motor connector.

  4. Measure the voltage according to the value(s) in the table below.

    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    J11-10 (UP) - J11-1 (GND)
    L - W-B
    Power window up operation
    Ignition switch ON, power window regulator switch off → up
    11 to 14 V → Below 1 V
    J11-10 (UP) - J11-1 (GND)
    L - W-B
    Power window up operation
    Ignition switch ON, door glass fully open → power window auto up operation → door glass fully closed
    11 to 14 V → Below 1 V → 11 to 14 V
    J11-7 (DOWN) - J11-1 (GND)
    Y - B
    Power window down operation
    Ignition switch ON, power window regulator switch off → down
    11 to 14 V → Below 1 V
    J11-7 (DOWN) - J11-1 (GND)
    Y - B
    Power window down operation
    Ignition switch ON, door glass fully closed → power window auto down operation → door glass fully open
    11 to 14 V → Below 1 V → 11 to 14 V
    If the result is not as specified, the motor may be malfunctioning.


CHECK REAR POWER WINDOW REGULATOR MOTOR RH
B158006E20
  1. Disconnect the J4 motor connector.

  2. Measure the resistance and voltage according to the value(s) in the table below.

    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    J4-2 (B) - J4-1 (GND)
    L - W-B
    Battery power supply
    Always
    11 to 14 V
    J4-1 (GND) - Body ground
    W-B - Body ground
    Ground
    Always
    Below 1 Ω
    If the result is not as specified, there may be a malfunction on the wire harness side.

  3. Reconnect the J4 motor connector.

  4. Measure the voltage according to the value(s) in the table below.

    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    J4-10 (UP) - J4-1 (GND)
    L - W-B
    Power window up operation
    Ignition switch ON, power window regulator switch off → up
    11 to 14 V → Below 1 V
    J4-10 (UP) - J4-1 (GND)
    L - W-B
    Power window up operation
    Ignition switch ON, door glass fully open → power window auto up operation → door glass fully closed
    11 to 14 V → Below 1 V → 11 to 14 V
    J4-7 (DOWN) - J4-1 (GND)
    B - W-B
    Power window down operation
    Ignition switch ON, power window regulator switch off → down
    11 to 14 V → Below 1 V
    J4-7 (DOWN) - J4-1 (GND)
    B - W-B
    Power window down operation
    Ignition switch ON, door glass fully closed → power window auto down operation → door glass fully open
    11 to 14 V → Below 1 V → 11 to 14 V
    If the result is not as specified, the motor may be malfunctioning.


CHECK MULTIPLEX NETWORK MASTER SWITCH
B158007E20
  1. Disconnect the I11*1 or I22*2 master switch connector.

    HINT:
    1. *1: for LHD
    2. *2: for RHD

  2. Measure the resistance and voltage according to the value(s) in the table below.

    for LHD 
    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    I11-11 (B) - I11-12 (GND)
    L - W-B
    Battery power supply
    Always
    11 to 14 V
    I11-12 (GND) - Body ground
    W-B - Body ground
    Ground
    Always
    Below 1 Ω
    for RHD 
    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    I22-11 (B) - I22-12 (GND)
    L - W-B
    Battery power supply
    Always
    11 to 14 V
    I22-12 (GND) - Body ground
    W-B - Body ground
    Ground
    Always
    Below 1 Ω
    If the result is not as specified, there may be a malfunction on the wire harness side.

  3. Reconnect the I11*1 or I22*2 master switch connector.

    HINT:
    1. *1: for LHD
    2. *2: for RHD

  4. Measure the voltage according to the value(s) in the table below.

    for LHD 
    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    I11-20 (UP) - I11-12 (GND)
    L - W-B
    Power window up operation
    Ignition switch ON, multiplex network master switch off → up
    11 to 14 V → Below 1 V
    I11-20 (UP) - I11-12 (GND)
    L - W-B
    Power window up operation
    Ignition switch ON, door glass fully open → power window auto up operation → door glass fully closed
    11 to 14 V → Below 1 V → 11 to 14 V
    I11-15 (DOWN) - I11-12 (GND)
    B - W-B
    Power window down operation
    Ignition switch ON, multiplex network master switch off → down
    11 to 14 V → Below 1 V
    I11-15 (DOWN) - I11-12 (GND)
    B - W-B
    Power window down operation
    Ignition switch ON, door glass fully closed → power window auto down operation → door glass fully open
    11 to 14 V → Below 1 V → 11 to 14 V
    for RHD 
    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    I22-20 (UP) - I22-12 (GND)
    L - W-B
    Power window up operation
    Ignition switch ON, multiplex network master switch off → up
    11 to 14 V → Below 1 V
    I22-20 (UP) - I22-12 (GND)
    L - W-B
    Power window up operation
    Ignition switch ON, door glass fully open → power window auto up operation → door glass fully closed
    11 to 14 V → Below 1 V → 11 to 14 V
    I22-15 (DOWN) - I22-12 (GND)
    B - W-B
    Power window down operation
    Ignition switch ON, multiplex network master switch off → down
    11 to 14 V → Below 1 V
    I22-15 (DOWN) - I22-12 (GND)
    B - W-B
    Power window down operation
    Ignition switch ON, door glass fully closed → power window auto down operation → door glass fully open
    11 to 14 V → Below 1 V → 11 to 14 V
    If the result is not as specified, the master switch may be malfunctioning.


CHECK FRONT PASSENGER SIDE POWER WINDOW REGULATOR SWITCH
B192192E01
  1. Disconnect the I3*1 or I25*2 switch connector.

    HINT:
    1. *1: for LHD
    2. *2: for RHD

  2. Measure the resistance according to the value(s) in the table below.

    for LHD 
    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    I3-1 (GND) - Body ground
    W-B - Body ground
    Ground
    Always
    Below 1 Ω
    for RHD 
    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    I25-1 (GND) - Body ground
    W-B - Body ground
    Ground
    Always
    Below 1 Ω
    If the result is not as specified, there may be a malfunction on the wire harness side.

  3. Reconnect the I3*1 or I25*2 switch connector.

    HINT:
    1. *1: for LHD
    2. *2: for RHD

  4. Measure the voltage according to the value(s) in the table below.

    for LHD 
    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    I3-6 (UP) - I3-1 (GND)
    L - W-B
    Power window up operation
    Ignition switch ON, power window regulator switch off → up
    11 to 14 V → Below 1 V
    I3-7 (DOWN) - I3-1 (GND)
    B - W-B
    Power window down operation
    Ignition switch ON, power window regulator switch off → down
    11 to 14 V → Below 1 V
    I3-8 (AUTO) - I3-1 (GND)
    R - W-B
    Power window up operation
    Ignition switch ONand door glass fully open → power window auto up operation → door glass fully closed
    11 to 14 V → Below 1 V → 11 to 14 V
    I3-8 (AUTO) - I3-1 (GND)
    R - W-B
    Power window down operation
    Ignition switch ON, door glass fully closed → power window auto down operation → door glass fully open
    11 to 14 V → Below 1 V → 11 to 14 V
    for RHD 
    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    I25-6 (UP) - I25-1 (GND)
    L - W-B
    Power window up operation
    Ignition switch ON, power window regulator switch off → up
    11 to 14 V → Below 1 V
    I25-7 (DOWN) - I25-1 (GND)
    B - W-B
    Power window down operation
    Ignition switch ON, power window regulator switch off → down
    11 to 14 V → Below 1 V
    I25-8 (AUTO) - I25-1 (GND)
    R - W-B
    Power window up operation
    Ignition switch ONand door glass fully open → power window auto up operation → door glass fully closed
    11 to 14 V → Below 1 V → 11 to 14 V
    I25-8 (AUTO) - I25-1 (GND)
    R - W-B
    Power window down operation
    Ignition switch ON, door glass fully closed → power window auto down operation → door glass fully open
    11 to 14 V → Below 1 V → 11 to 14 V
    If the result is not as specified, the switch may be malfunctioning.


CHECK REAR POWER WINDOW REGULATOR SWITCH LH
B129574E11
  1. Disconnect the J10 switch connector.

  2. Measure the resistance according to the value(s) in the table below.

    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    J10-1 (GND) - Body ground
    W-B - Body ground
    Ground
    Always
    Below 1 Ω
    If the result is not as specified, there may be a malfunction on the wire harness side.

  3. Reconnect the J10 switch connector.

  4. Measure the voltage according to the value(s) in the table below.

    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    J10-6 (UP) - J10-1 (GND)
    L - W-B
    Power window up operation
    Ignition switch ON, power window regulator switch off → up
    11 to 14 V → Below 1 V
    J10-7 (DOWN) - J10-1 (GND)
    B - W-B
    Power window down operation
    Ignition switch ON, power window regulator switch off → down
    11 to 14 V → Below 1 V
    J10-8 (AUTO) - J10-1 (GND)
    R - W-B
    Power window up operation
    Ignition switch ON, door glass fully open → power window auto up operation → door glass fully closed
    11 to 14 V → Below 1 V → 11 to 14 V
    J10-8 (AUTO) - J10-1 (GND)
    R - W-B
    Power window down operation
    Ignition switch ON, door glass fully closed → power window auto down operation → door glass fully open
    11 to 14 V → Below 1 V → 11 to 14 V
    If the result is not as specified, the switch may be malfunctioning.


CHECK REAR POWER WINDOW REGULATOR SWITCH RH
B129574E12
  1. Disconnect the J3 switch connector.

  2. Measure the resistance according to the value(s) in the table below.

    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    J3-1 (GND) - Body ground
    W-B - Body ground
    Ground
    Always
    Below 1 Ω
    If the result is not as specified, there may be a malfunction on the wire harness side.

  3. Reconnect the J3 switch connector.

  4. Measure the voltage according to the value(s) in the table below.

    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    J3-6 (UP) - J3-1 (GND)
    L - W-B
    Power window up operation
    Ignition switch ON, power window regulator switch off → up
    11 to 14 V → Below 1 V
    J3-7 (DOWN) - J3-1 (GND)
    B - W-B
    Power window down operation
    Ignition switch ON, power window regulator switch off → down
    11 to 14 V → Below 1 V
    J3-8 (AUTO) - J3-1 (GND)
    R - W-B
    Power window up operation
    Ignition switch ON, door glass fully open → power window auto up operation → door glass fully closed
    11 to 14 V → Below 1 V → 11 to 14 V
    J3-8 (AUTO) - J3-1 (GND)
    R - W-B
    Power window down operation
    Ignition switch ON, door glass fully closed → power window auto down operation → door glass fully open
    11 to 14 V → Below 1 V → 11 to 14 V
    If the result is not as specified, the switch may be malfunctioning.


CHECK MAIN BODY ECU (COWL SIDE JUNCTION BLOCK LH)
B174142E03
  1. Disconnect the 2A, 2C, E1, E2 and E3 ECU connectors.

  2. Measure the resistance and voltage according to value(s) in the table below.

    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    E3-1 (GND3) - 2A-62 (GND2)
    BR - W-B
    Ground
    Always
    Below 1 Ω
    2D-62 (GND2) - Body ground
    W-B - Body ground
    Ground
    Always
    Below 1 Ω
    2A-1 (IG) - Body ground
    B - Body ground
    IG power supply
    Always
    11 to 14 V
    E2-1 (AM2) - Body ground
    W - Body ground
    Battery power supply
    Always
    11 to 14 V
    E1-6 (AM1) - Body ground
    W - Body ground
    Battery power supply
    Always
    11 to 14 V
    E1-24 (DCTY) - Body ground
    L - Body ground
    Driver side door courtesy light switch input
    Driver side door open
    Below 1 Ω
    Driver side door closed
    10 kΩ or higher
    E2-21 (PCTY) - Body ground
    Y - Body ground
    Front passenger side door courtesy light switch input
    Front passenger side door open
    Below 1 Ω
    Front passenger side door closed
    10 kΩ or higher
    E2-7 (RCTY) - Body ground
    G - Body ground
    Rear RH side door courtesy light switch input
    Rear RH side door open
    Below 1 Ω
    Rear RH side door closed
    10 kΩ or higher
    2C-2 (LCTY) - Body ground
    W - Body ground
    Rear LH side door courtesy light switch input
    Rear LH side door open
    Below 1 Ω
    Rear LH side door closed
    10 kΩ or higher
    1. If the result is not as specified, the wire harness side may have a malfunction.

← PROBLEM SYMPTOMS TABLE (from Jan 2012)DTC CHECK / CLEAR (from Sep 2011) →