2011-2013 Land Cruiser · Service Manual Engine / Hybrid / EV System

PRECAUTION

Precautions · Vehicles built Sep 2011 – Dec 2011

CAUTION:
  1. Before working on the fuel system, disconnect the cable from the negative (-) battery terminal.
  2. Do not smoke or be near an open flame when working on the fuel system.
  3. Keep gasoline away from rubber and leather parts.


1.DISCHARGE FUEL SYSTEM PRESSURE

CAUTION:
  1. Do not disconnect any part of the fuel system until you have discharged the fuel system pressure.
  2. After discharging the fuel pressure, place a cloth or equivalent over fittings as you separate them to reduce the risk of fuel spray on yourself or in the engine compartment.

  1. Remove the engine room relay block cover.

  2. A176383E02
    Remove the circuit opening relay (C/OPN).

  3. Start the engine. After the engine has stopped on its own, turn the engine switch off.

    HINT:
    If DTC P0230 is output, clear the DTC (Click here).

  4. Crank the engine, then check that the engine does not start.

  5. Loosen the fuel tank cap, then discharge the pressure in the fuel tank completely.

  6. Disconnect the cable from negative (-) battery terminal.

    NOTICE:
    When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).

  7. Install the circuit opening relay (C/OPN).

  8. Install the engine room relay block cover.


2.FUEL SYSTEM

  1. When disconnecting the high fuel pressure line, a large amount of gasoline will spill out. Follow these procedures.

    1. Discharge the fuel system pressure.

    2. A133694
      Put a container under the connecting part of the pressure line.

    3. Slowly loosen the connection.

    4. Disconnect the connection.

    5. Plug the connection with a rubber plug.

  2. When connecting the union bolt (fuel pressure pulsation damper) on the high pressure pipe union, observe the following procedures.
    A167923E02

    NOTICE:
    Make sure to install the gaskets in the order shown in the illustration, as the shape of the upper side and lower side gaskets is different.


    1. Always use 2 new gaskets.

    2. Tighten the union bolt by hand.

    3. A130783E03
      Using SST, tighten the union bolt to the specified torque.
      SST
      09612-24014   (09617-24011)

      Torque:
      with SST:
      33 N*m{ 340 kgf*cm , 24 ft.*lbf }
      without SST:
      39 N*m{ 398 kgf*cm , 29 ft.*lbf }

      HINT:
      1. Use a torque wrench with a fulcrum length of 30 cm (11.8 in.).
      2. Make sure SST and the wrench are connected in a straight line.

  3. A181411E01
    Observe the following precautions when removing or installing the injectors:

    NOTICE:
    1. Never reuse the O-ring.
    2. When placing a new O-ring on the injector, do not damage the O-ring.
    3. Coat the new O-ring with spindle oil or gasoline before installing. Do not use engine oil, gear oil or brake fluid.

  4. A231768E01
    Install the injector to the delivery pipe and intake manifold, as shown in the illustration.

    NOTICE:
    Before installing the injector, apply spindle oil or gasoline where the delivery pipe or intake manifold contacts the O-ring of the injector.

  5. Observe these precautions when disconnecting the fuel tube connector (for quick type A).

    1. C157056E01
      for Fuel Pipe Clamp Type:
      Remove the fuel pipe clamp from the fuel tube connector.

    2. A157617E02
      for Fuel Hose Connector Cover Type:
      Detach the lock claw by lifting up the cover, as shown in the illustration.

    3. Check for dirt or mud on the pipe and around the connector before disconnection. Clean if necessary.

    4. A088336E20
      Pinch the connector and disconnect the connector and pipe.
      If the connector and the pipe are stuck together, pinch the connector, then push and pull the pipe to disconnect the pipe and pull it out.

      NOTICE:
      Do not use any tools in this procedure.

    5. Check for dirt or mud on the seal surface of the disconnected pipe. Clean if necessary.

    6. A099427E11
      To protect the disconnected pipe and connector from damage and contamination, cover it with a plastic bag.

  6. Observe these precautions when disconnecting the fuel tube connector (for quick type B).

    1. A167866E01
      Check that there is no damage or foreign matter on the part of the pipe that contacts the connector.

    2. A091246E02
      Detach the 2 claws of the connector retainer. Push down on the connector and disconnect it from the pipe.

      HINT:
      If the connector and pipe are stuck, pinch the fuel pipe by hand, and push and pull the connector to disconnect it.

      NOTICE:
      Do not use any tools in this procedure.

    3. Check for foreign matter on the seal surface of the disconnected pipe. Clean it if necessary.

    4. A103972E02
      To protect the disconnected pipe and connector from damage and foreign matter, cover it with a plastic bag.

  7. Observe these precautions when connecting the fuel tube connector (for quick type B).

    1. A125397E01
      Check for foreign matter on the pipe and around the connector before connecting it. Clean it if necessary.

    2. Align the axis of the connector with the axis of the pipe. Push the pipe into the connector, and push up on the retainer.

    3. A093435
      After connecting the pipe and connector, try to pull them apart to confirm that they are securely connected.

  8. A130944E01
    Observe these precautions when connecting the fuel tube connector (for quick type A).

    1. Check that there is no damage or contamination in the connected part of the pipe.

    2. Align the axis of the connector with the axis of the pipe. Push the pipe into the connector until the connector makes a "click" sound. If the connection is tight, apply a small amount of fresh spindle oil or gasoline on the tip of the pipe.

    3. A130945E02
      After having finished the connection, try to pull apart the pipe and the connector to confirm that they are securely connected.

    4. A157616E01
      for Fuel Hose Connector Cover Type:
      Attach the lock claw to the connector by pushing down on the cover, as shown in the illustration.

    5. C157056E01
      for Fuel Pipe Clamp Type:
      Install the fuel pipe clamp to the connector.

    6. Check that there is no fuel leakage.


3.CHECK FOR FUEL LEAK
  1. Check that there are no fuel leaks after performing maintenance anywhere on the fuel system (Click here).

← INSTALLATION (from Jan 2012)PARTS LOCATION (Sep 2011 – Dec 2011) →