2011-2013 Land Cruiser · Service Manual Engine / Hybrid / EV System

PRECAUTION

Precautions · Vehicles built from Jan 2012

CAUTION:
  1. Before working on the fuel system, disconnect the cable from the negative (-) battery terminal.
  2. Do not smoke or be near an open flame when working on the fuel system.
  3. Keep gasoline away from rubber and leather parts.


1.DISCHARGE FUEL SYSTEM PRESSURE

CAUTION:
  1. Do not disconnect any part of the fuel system until you have discharged the fuel system pressure.
  2. After discharging the fuel pressure, place a cloth or equivalent over fittings as you separate them to reduce the risk of fuel spray on yourself or in the engine compartment.

  1. Disconnect the fuel pump ECU connector (Click here).

  2. Start the engine. After the engine stops, turn the engine switch off.

    HINT:
    DTC P0171/0174 (system too lean) may be stored.

  3. Crank the engine again, and then check that the engine does not start.

  4. Loosen the fuel tank cap, and then discharge the pressure in the fuel tank completely.

  5. Disconnect the cable from the negative (-) battery terminal.

    NOTICE:
    1. After turning the engine switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (Click here).
    2. When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).

  6. Connect the fuel pump ECU connector (Click here).


2.FUEL SYSTEM
  1. When disconnecting the high fuel pressure line, a large amount of gasoline will spill out. Follow these procedures.

    1. Perform the "DISCHARGE FUEL SYSTEM PRESSURE" procedures above.

    2. Disconnect the fuel tube.

    3. Drain any fuel remaining inside the fuel tube.

    4. To protect the disconnected fuel tube from damage and contamination, cover it with a plastic bag.

    5. Put a container under the connecting part of the pressure line.

  2. A163532E04
    Observe these precautions when removing and installing the injectors.
    Text in Illustration 
    *1
    O-ring
    *2
    Fuel Delivery Pipe
    *a
    CORRECT
    *b
    INCORRECT

    NOTICE:
    1. Never reuse the O-ring.
    2. When placing a new O-ring on the injector, do not damage it.
    3. Coat a new O-ring with spindle oil or gasoline before installing it.
    4. Do not use engine oil, gear oil or brake oil.

  3. A163533E03
    Install the injector to the delivery pipe and cylinder head as shown in the illustration.
    Text in Illustration 
    *1
    Fuel Delivery Pipe
    *2
    O-ring
    *3
    Fuel Injector
    *4
    Insulator
    *5
    Cylinder Head

    NOTICE:
    Before installing the injector, apply spindle oil or gasoline on the place where the delivery pipe contacts the O-ring of the injector.

  4. A223364E01
    Observe these precautions when disconnecting the fuel tube connector (for quick type A).

    1. Fuel Hose Connector Cover Type:
      Detach the lock claw by lifting up the cover as shown in the illustration.

      Text in Illustration 
      *1
      Fuel Hose Connector Cover

    2. Check for dirt or mud on the pipe and around the connector before disconnection. Clean if necessary.

    3. A088336E26
      Pinch the connector and disconnect the connector and pipe.
      Text in Illustration 
      *1
      Retainer
      V100135
      Pinch
      V100136
      Pull

      NOTICE:

      1. A224870E01
        Check for foreign matter in the pipe and around the connector. Clean if necessary. Foreign matter may damage the O-ring or cause leaks in the seal between the pipe and connector.
      2. Do not use any tools to separate the pipe and connector.
      3. Do not forcefully bend or twist the nylon tube.
      4. Check for foreign matter on the pipe seal surface. Clean if necessary.
      5. Put the pipe and connector ends in plastic bags to prevent damage and foreign matter contamination.
      6. If the pipe and connector are stuck together, pinch the connector between your fingers and turn it carefully to disconnect it.

      Text in Illustration 
      *1
      Retainer
      *2
      Nylon Tube
      *3
      Pipe
      *4
      O-ring
      *5
      Fuel Tube Connector

      HINT:
      If the connector and pipe are stuck, pinch the connector, push and pull the pipe to disconnect the pipe and pull it out.

    4. Check for dirt or mud on the seal surface of the disconnected pipe. Clean if necessary.

    5. To protect the disconnected pipe and connector from damage and contamination, cover them with a plastic bag.

  5. Observe these precautions when connecting the fuel tube connector (for quick type A).

    1. Before connecting the connector, check that there is no damage or contamination in the connecting part of the pipe.

    2. A071366E27
      Align the axis of the connector with the axis of the pipe. Push the pipe into the connector until the connector makes a "click" sound. If the connection is tight, apply a small amount of fresh spindle oil or gasoline to the tip of the pipe.
      Text in Illustration 
      V100135
      Push

    3. A071366E28
      After connecting the pipe and connector, check that the pipe and connector are securely connected by trying to pull them apart.
      Text in Illustration 
      V100135
      Pull

    4. Fuel Hose Connector Cover Type:
      Attach the lock claws to the connector by pushing down on the cover.

    5. Check for any fuel leaks.

  6. Observe these precautions when disconnecting the fuel tube connector (for quick type B).

    1. Check that there is no damage or foreign matter on the part of the pipe that contacts the connector.

    2. A224877E01
      Detach the 2 claws of the connector retainer. Push the retainer out and disconnect the connector from the pipe.
      Text in Illustration 
      *1
      Retainer
      V100135
      Push
      V100136
      Push Out
      V100137
      Pull

      HINT:
      A091246E02
      If the connector and pipe are stuck, pinch the fuel pipe by hand and push and pull the connector to disconnect it.

      Text in Illustration 
      V100135
      Pull
      V100136
      Push

      NOTICE:

      1. A224889E01
        Check for any dirt and foreign matter contamination in the pipe and around the connector. Clean if necessary. Foreign matter may damage the O-ring or cause leaks in the seal between the pipe and connector.
      2. Do not use any tools to separate the pipe and connector.
      3. Do not allow any scratches or foreign matter on the parts when disconnecting them, as the fuel tube joint contains the O-rings that seal the plug.
      4. Check for any dirt and foreign matter on the pipe seal surface. Clean if necessary.
      5. Do not forcibly bend, twist or turn the nylon tube.
      6. Protect the disconnected part by covering it with a plastic bag and tape after disconnecting the main tube.
      7. If the pipe and connector are stuck together, pinch the tube between your fingers and turn it carefully to free it. Then disconnect the main tube.

      Text in Illustration 
      *1
      Pipe
      *2
      Retainer
      *3
      Nylon Tube
      *4
      Connector
      *5
      O-ring

    3. Check for foreign matter on the seal surface of the disconnected pipe. Clean if necessary.

    4. To protect the disconnected pipe and connector from damage and foreign matter, cover them with a plastic bag.

  7. Observe these precautions when connecting the fuel tube connector (for quick type B).

    1. Check for foreign matter on the pipe and around the connector before connecting it. Clean if necessary.

    2. A125397E02
      A227055
      Align the axis of the connector with the axis of the pipe. Push the connector onto the pipe, and then push in the retainer.
      Text in Illustration 
      *1
      Retainer
      V100135
      Push In
      V100136
      Push

      NOTICE:
      1. Before connecting the tube connectors to the pipes, check if there is any damage or foreign matter in the connectors.
      2. After connecting the pipe and connector, check that the pipe and connector are securely connected by trying to pull them apart.

      Text in Illustration 
      V100135
      Pull

  8. Observe these precautions when handling the nylon tube.

    NOTICE:
    1. Be careful not to turn the connection part of the nylon tube and quick connector when connecting them.
    2. Do not kink the nylon tube.
    3. Do not bend the nylon tube as this may cause blockage.


3.FUEL SUCTION WITH PUMP AND GAUGE TUBE ASSEMBLY

NOTICE:
Do not disconnect the hoses indicated in the illustration.

A181496E02
Text in Illustration 
*a
for Single Tank Type
*b
for Double Tank Type

4.INSPECT FOR FUEL LEAK
(Click here)
← INSTALLATION (from Jan 2012)PARTS LOCATION (from Jan 2012) →