2011-2013 Land Cruiser · Service Manual Engine / Hybrid / EV System

REMOVAL

Removal / installation · Vehicles built Sep 2011 – Dec 2011


1. DISCHARGE FUEL SYSTEM PRESSURE
  1. Discharge the fuel system pressure (Click here).


2. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

NOTICE:
When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).


3. REMOVE FRONT FENDER SPLASH SHIELD SUB-ASSEMBLY LH

B180991
  1. Remove the 3 bolts and screw.

  1. Turn the clip indicated by the arrow in the illustration to remove the fender splash shield.


4. REMOVE FRONT FENDER SPLASH SHIELD SUB-ASSEMBLY RH

HINT:
Use the same procedures described for the LH side.


5. REMOVE NO. 1 ENGINE UNDER COVER SUB-ASSEMBLY

  1. A178461
    Remove the 10 bolts and No. 1 engine under cover.


6. DRAIN ENGINE COOLANT

CAUTION:
Do not remove the radiator cap while the engine and radiator are still hot. Pressurized, hot engine coolant and steam may be released and cause serious burns.


A175216E01
  1. Loosen the radiator drain cock plug.

  1. Remove the radiator cap. Then drain the coolant.

    HINT:
    Collect the coolant in a container and dispose of it according to the regulations in your area.

  1. Loosen the 2 cylinder block drain cock plugs. Then drain the coolant from the engine.

  1. Tighten the 2 cylinder block drain cock plugs.

    Torque:
    13 N*m{ 130 kgf*cm , 9 ft.*lbf }

  1. Tighten the radiator drain cock plug by hand.


7. REMOVE V-BANK COVER SUB-ASSEMBLY

  1. A178998
    Remove the 2 nuts and V-bank cover.


8. REMOVE AIR CLEANER HOSE ASSEMBLY

  1. A175163
    Disconnect the vacuum transmitting hose and No. 2 ventilation hose.

  1. Loosen the 2 hose clamps.

  1. Remove the air cleaner hose.


9. REMOVE NO. 2 V-BANK COVER BRACKET

  1. A178998
    Remove the 2 nuts and V-bank cover.


10. REMOVE NO. 2 WATER BY-PASS PIPE SUB-ASSEMBLY

  1. A179572
    Disconnect the 4 water hoses from the No. 2 water by-pass pipe.

  1. A179573
    Remove the 2 bolts.

  1. Remove the No. 2 water by-pass pipe.


11. DISCONNECT FUEL HOSE

  1. A176355E02
    Remove the fuel hose clamp.

  1. Pinch and pull the fuel hose connector to disconnect the connector from the fuel pipe.

    NOTICE:
    1. Check for foreign matter in the pipe and around the connector. Clean if necessary. Foreign matter may damage the O-ring or cause leaks in the seal between the pipe and connector.
    2. Do not use any tools to separate the pipe and connector.
    3. Do not forcefully bend or twist the nylon tube.
    4. Check for foreign matter on the pipe seal surface. Clean if necessary.
    5. Put the pipe and connector ends in plastic bags to prevent damage and foreign matter contamination.
    6. If the pipe and connector are stuck together, pinch the connector between your fingers and turn it carefully to disconnect it.


12. REMOVE NO. 2 FUEL HOSE

  1. for engine side:

    1. A176296E01
      Detach the fuel hose clamp.

    2. Detach the lock claw by lifting up the cover, as shown in the illustration.

    3. Pinch and pull the No. 2 fuel hose connector to disconnect the connector from the No. 3 fuel pipe.

      NOTICE:
      1. Check for foreign matter in the pipe and around the connector. Clean if necessary. Foreign matter may damage the O-ring or cause leaks in the seal between the pipe and connector.
      2. Do not use any tools to separate the pipe and connector.
      3. Do not forcefully bend or twist the nylon tube.
      4. Check for foreign matter on the pipe seal surface. Clean if necessary.
      5. Put the pipe and connector ends in plastic bags to prevent damage and foreign matter contamination.
      6. If the pipe and connector are stuck together, pinch the connector between your fingers and turn it carefully to disconnect it.

  1. for body side:

    1. A176357E01
      Pinch and pull the No. 2 fuel hose connector to disconnect the connector from the fuel pipe.

      NOTICE:
      1. Check for foreign matter in the pipe and around the connector. Clean if necessary. Foreign matter may damage the O-ring or cause leaks in the seal between the pipe and connector.
      2. Do not use any tools to separate the pipe and connector.
      3. Do not forcefully bend or twist the nylon tube.
      4. Check for foreign matter on the pipe seal surface. Clean if necessary.
      5. Put the pipe and connector ends in plastic bags to prevent damage and foreign matter contamination.
      6. If the pipe and connector are stuck together, pinch the connector between your fingers and turn it carefully to disconnect it.


13. REMOVE NO. 2 VENTILATION HOSE

  1. A175165
    w/ Secondary Air Injection System:

    1. Remove the No. 2 ventilation hose from the cylinder head cover.

    2. Remove the clamp.

    3. Remove the vacuum transmitting hose from the fuel pressure regulator.

  1. A175164
    w/o Secondary Air Injection System:

    1. Remove the No. 2 ventilation hose from the cylinder head cover.

    2. Remove the vacuum transmitting hose from the fuel pressure regulator.


14. REMOVE NO. 1 VENTILATION HOSE

  1. A181858
    Remove the No. 1 ventilation hose from the intake manifold and ventilation valve.


15. DISCONNECT PURGE VSV

  1. A159752
    Disconnect the purge VSV connector.

  1. Disconnect the purge line hose from the purge VSV.

  1. Remove the bolt and disconnect the purge VSV from the intake manifold.


16. DISCONNECT ENGINE WIRE

  1. A179576
    Disconnect the VSV connector (for ACIS).

  1. Disconnect the 2 wire clamps from the wire bracket and engine hanger.

  1. A179577
    Disconnect the 2 wire clamps from the wire clamp bracket on the RH delivery pipe.

  1. Disconnect the 8 injector connectors.

  1. A156173
    Remove the 2 bolts and disconnect the engine wire protector.


17. REMOVE VACUUM CONTROL VALVE SET (w/ Secondary Air Injection System)

  1. A179568
    Disconnect the 2 VSV connectors.

  1. Disconnect the 3 vacuum hoses.

  1. Remove the 2 bolts and vacuum control valve set.


18. REMOVE NO. 1 FUEL PIPE SUB-ASSEMBLY

  1. A176335E01
    Remove the bolt, 2 union bolts, 4 gaskets and No. 1 fuel pipe.


19. DISCONNECT NO. 3 FUEL PIPE SUB-ASSEMBLY

  1. A160920
    Disconnect the fuel return hose from the pressure regulator.

    NOTICE:
    Put a cloth or equivalent under the pressure regulator.

  1. A160921
    Remove the 3 bolts and disconnect the No. 3 fuel pipe from the intake manifold and fuel delivery pipe LH.


20. REMOVE FUEL DELIVERY PIPE SUB-ASSEMBLY

  1. A176354
    Remove the 4 nuts holding the delivery pipes to the intake manifold.

  1. Remove the 2 delivery pipes from the intake manifold.

    NOTICE:
    Be careful not to drop the injectors when removing the delivery pipes.


21. REMOVE FUEL INJECTOR ASSEMBLY

  1. A181413E01
    Remove the 8 injectors from the delivery pipe LH and RH.

    NOTICE:
    Do not apply any load to the injector in the horizontal direction.

  1. Remove the O-ring and insulator from each injector.

← ON-VEHICLE INSPECTION (Sep 2011 – Dec 2011)INSPECTION (Sep 2011 – Dec 2011) →