No Answer-Back
Circuit diagnosis · Vehicles built from Jan 2012
Versions by build date: Sep 2011 – Dec 2011 from Jan 2012
DESCRIPTION
In some cases, wireless door lock control functions are normal but the turn signal lights and wireless door lock buzzer are not. Malfunctions may be present in the main body ECU, certification ECU (smart key ECU assembly), turn signal lights, and/or wireless door lock buzzer signal outputs.*- NOTICE:
- Before performing the inspection, check that there are no problems related to the CAN communication system and LIN communication system.
- When troubleshooting a function, first make sure that the answer-back function is set to the default setting.
- Check that DTC B1242 is not output.
- When troubleshooting a function, first make sure that the open door warning function is set to the default setting.
- Before performing the inspection, check that there are no problems related to the CAN communication system and LIN communication system.
- HINT:
- *: For Europe and China, there is no buzzer sound answer-back function.
WIRING DIAGRAM


INSPECTION PROCEDURE
| 1. READ VALUE USING INTELLIGENT TESTER (DOOR LOCK POSITION SWITCH) |
Connect the intelligent tester to the DLC3.
Turn the engine switch on (IG).
Turn the intelligent tester on.
Enter the following menus: Body / Main Body / Data List.
Read the Data List according to the display on the intelligent tester.
Main Body Tester Display
Measurement Item / Range
Normal Condition
Diagnostic Note
D Lock Pos switch
Driver side door lock position switch signal / ON or OFF
ON: Driver side door lock is unlocked
OFF: Driver side door lock is locked
-
P Lock Pos switch
Passenger side door lock position switch signal / ON or OFF
ON: Passenger side door is unlocked
OFF: Passenger side door is locked
-
RL Lock Pos switch
Rear door LH lock position switch signal / ON or OFF
ON: Rear side door LH is unlocked
OFF: Rear side door LH is locked
-
RR Lock Pos switch
Rear door RH lock position switch signal / ON or OFF
ON: Rear side door RH is unlocked
OFF: Rear side door RH is locked
-
Back Lock Pos switch
Back door lock position switch signal / ON or OFF
ON: Back door is unlocked
OFF: Back door is locked
-
- OK:
- On the intelligent tester screen, the display changes between LOCK and UNLOCK as shown in the chart above.
- HINT:
- Go to POWER DOOR LOCK CONTROL SYSTEM (Proceed to Only Driver Door LOCK/UNLOCK Functions do not Operate) (Click here).
- Go to POWER DOOR LOCK CONTROL SYSTEM (Proceed to Only Passenger Door LOCK/UNLOCK Functions do not Operate) (Click here).
- Go to POWER DOOR LOCK CONTROL SYSTEM (Proceed to Only Rear Door LH LOCK/UNLOCK Functions do not Operate) (Click here).
- Go to POWER DOOR LOCK CONTROL SYSTEM (Proceed to Only Rear Door RH LOCK/UNLOCK Functions do not Operate) (Click here).
- Go to POWER DOOR LOCK CONTROL SYSTEM (Proceed to Only Back Door LOCK/UNLOCK Functions do not Operate) (Click here).
- Go to POWER DOOR LOCK CONTROL SYSTEM (Proceed to Only Driver Door LOCK/UNLOCK Functions do not Operate) (Click here).
|
|
||||
| OK | |
| 2. CHECK WIRELESS DOOR LOCK FUNCTION |
Check that the wireless door lock control functions operate with a transmitter (Click here).
Result Result
Proceed to
Wireless door lock control functions operate normally but turn signal light answer-back does not occur
A
Wireless door lock control functions operate normally but wireless door lock buzzer answer-back does not occur
B
|
|
||||
| A | |
| 3. CHECK HAZARD WARNING LIGHT |
Check that the turn signal lights flash continuously when the hazard warning signal switch is pressed (Click here).
- OK:
- Hazard warning lights flash continuously.
|
|
||||
| OK | ||
| ||
| 4. CHECK HARNESS AND CONNECTOR (WIRELESS DOOR LOCK BUZZER - CERTIFICATION ECU AND BODY GROUND) |
Disconnect the E29 ECU connector.
Disconnect the A20 buzzer connector.
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Condition
Specified Condition
A20-1 - E29-21 (BZR)
Always
Below 1 Ω
A20-2 - Body ground
A20-1 - Body ground
Always
10 kΩ or higher
|
|
||||
| OK | |
| 5. CHECK WIRELESS DOOR LOCK BUZZER (OPERATION) |
Temporarily replace the wireless door lock buzzer with a new one (Click here).
Check that the wireless door lock buzzer sounds by using the transmitter lock/unlock switch.
- OK:
- Wireless door lock buzzer sounds.
|
|
||||
| OK | ||
| ||
