2011-2013 Land Cruiser · Service Manual Engine / Hybrid / EV System

INSTALLATION

Removal / installation · Vehicles built Sep 2011 – Dec 2011


1. INSTALL OIL COOLER ASSEMBLY

  1. A150134E03
    Clean the oil cooler contact surface on the cooler mounting.

  1. Apply a light coat of engine oil to a new gasket and install it to the oil cooler.

  1. Apply a light coat of engine oil on the threads and under the head of the union bolt.

  1. A178908
    Install the oil cooler and plate washer with the union bolt.

    Torque:
    69 N*m{ 700 kgf*cm , 51 ft.*lbf }

    HINT:
    Fit the fork part of the oil cooler onto the rib of the oil cooler bracket.

  1. Connect the 2 oil cooler hoses to the oil cooler.


2. INSTALL OIL FILTER ASSEMBLY

  1. A150110
    Clean and check the oil filter installation surface.

  1. Apply clean engine oil to the gasket of a new oil filter.

  1. Lightly screw the oil filter into place by hand. Tighten it until the gasket contacts the seat.

  1. A150111E02
    Using SST, tighten the oil filter. Choose from the following to tighten the oil filter.
    SST
    09228-07501  

    1. Using a torque wrench, tighten the oil filter.

      Torque:
      17 N*m{ 175 kgf*cm , 13 ft.*lbf }

    2. Tighten the oil filter a 3/4 turn by hand or with a common wrench.


3. ADD ENGINE OIL
  1. Install a new gasket and the drain plug.

    Torque:
    39 N*m{ 398 kgf*cm , 29 ft.*lbf }

  1. Add new engine oil.

    Standard Engine Oil:
    Oil Grade
    Oil Viscosity (SAE)
    API grade SL "Energy-Conserving", SM "Energy-Conserving" or ILSAC multigrade engine oil
    10W-30
    (10W-30 is best choice for fuel economy and good starting in cold weather).
    API grade SL or SM multigrade engine oil
    10W-30

    Standard Oil Capacity:
    Item
    Specified Condition
    Drain and refill with oil filter change
    6.2 liters (6.6 US qts, 5.5 Imp. qts)
    Drain and refill without oil filter change
    5.7 liters (6.0 US qts, 5.0 Imp. qts)
    Dry fill
    7.1 liters (7.5 US qts, 6.2 Imp. qts)


4. INSTALL OIL FILLER CAP SUB-ASSEMBLY

5. ADD ENGINE COOLANT
  1. Add engine coolant.

    Standard Capacity:
    Item
    Specified Condition
    w/o Transmission oil cooler
    w/o Rear Heater
    13.4 liters (14.2 US qts, 11.8 Imp. qts)
    w/ Rear Heater
    16.3 liters (17.2 US qts, 14.3 Imp. qts)
    w/ Transmission oil cooler
    w/o Rear Heater
    14.1 liters (14.9 US qts, 12.4 Imp. qts)
    w/ Rear Heater
    16.9 liters (17.9 US qts, 14.9 Imp. qts)

    HINT:
    TOYOTA vehicles are filled with TOYOTA SLLC at the factory. In order to avoid damage to the engine cooling system and other technical problems, only use TOYOTA SLLC or similar high quality ethylene glycol based non-silicate, non-amine, non-nitrite, non-borate coolant with long-life hybrid organic acid technology (coolant with long-life hybrid organic acid technology consists of a combination of low phosphates and organic acids).

  1. A168577
    Slowly pour coolant into the radiator reservoir until it reaches the F line.

  1. Install the radiator reservoir cap.

  1. Press the inlet and outlet radiator hoses several times by hand, and then check the coolant level. If the coolant level is low, add coolant.

  1. Install the radiator cap.

  1. Start the engine and warm it up until the thermostat opens.

    NOTICE:
    Switch off the A/C.

  1. Maintain the engine speed at 2000 to 2500 rpm.

    NOTICE:
    1. Make sure that the radiator reservoir still has some coolant in it.
    2. Pay attention to the needle of the water temperature meter. Make sure that the needle does not show an abnormally high temperature.
    3. If there is not enough coolant, the engine may burn out or overheat.
    4. Immediately after starting the engine, if the radiator reservoir does not have any coolant, perform the following: 1) stop the engine, 2) wait until the coolant has cooled down, and 3) add coolant until the coolant is filled to the F line.
    5. Run the engine at 2000 rpm until the coolant level has stabilized.

  1. Press the inlet and outlet radiator hoses several times by hand to bleed air.

    CAUTION:
    1. Wear protective gloves.
    2. Be careful as the radiator hoses are hot.
    3. Keep your hands away from the cooling fan.

  1. Stop the engine, and wait until the engine coolant cools down to the ambient temperature.

    CAUTION:
    Do not remove the radiator cap while the engine and radiator are still hot. Pressurized, hot engine coolant and steam may be released and cause serious burns.

  1. A168578
    Check that the coolant level is between the F and L lines. If the coolant level is below the L line, repeat all of the procedures above. If the coolant level is above the F line, drain coolant so that the coolant level is between the F and L lines.


6. INSPECT FOR OIL LEAK
  1. Start the engine. Make sure that there are no oil leaks from the area that was worked on.


7. INSPECT FOR COOLANT LEAK

  1. A168576
    Fill the radiator with coolant and attach a radiator cap tester.

  1. Warm up the engine.

  1. Using the radiator cap tester, increase the pressure inside the radiator to 123 kPa (1.3 kgf/cm2, 18 psi), and check that the pressure does not drop.
    If the pressure drops, check the hoses, radiator and water pump for leaks. If no external leaks are found, check the heater core, cylinder block and head.


8. CHECK ENGINE OIL LEVEL
  1. Warm up the engine, then stop the engine and wait for 5 minutes.

  1. Check that the engine oil level is between the low level and full level marks on the dipstick.
    If low, check for leakage and add oil up to the full level mark.

    NOTICE:
    Do not fill engine oil above the full level mark.


9. INSTALL REAR ENGINE UNDER COVER SEAL

  1. A178890
    Install the cover seal with the 2 bolts.


10. INSTALL NO. 1 ENGINE UNDER COVER SUB-ASSEMBLY

  1. A178461
    Install the No. 1 engine under cover with the 10 bolts.

    Torque:
    29 N*m{ 296 kgf*cm , 21 ft.*lbf }


11. INSTALL FRONT FENDER SPLASH SHIELD SUB-ASSEMBLY LH

B180991
  1. Push in the clip indicated by the arrow in the illustration to install the fender splash shield.

  1. Install the 3 bolts and screw.


12. INSTALL FRONT FENDER SPLASH SHIELD SUB-ASSEMBLY RH

HINT:
Use the same procedures described for the LH side.


13. INSPECT ENGINE COOLANT LEVEL

A178872
  1. Check that the engine coolant level is between the L and F lines when the engine is cold.
    If the engine coolant is low, check for leaks and add "TOYOTA Super Long Life Coolant" or similar high quality ethylene glycol based non-silicate, non-amine, non-nitrite and non-borate coolant with long-life hybrid organic acid technology to the F line.

    NOTICE:
    Do not substitute plain water for engine coolant.

  1. Remove the radiator cap, and check that the coolant level is up to the radiator filler hole.

← INSPECTION (Sep 2011 – Dec 2011)ON-VEHICLE INSPECTION (from Sep 2011) →