2011-2013 Land Cruiser · Service Manual Engine / Hybrid / EV System

REMOVAL

Removal / installation · Vehicles built Sep 2011 – Dec 2011

Versions by build date: Sep 2011 – Dec 2011 from Jan 2012


1. REMOVE UPPER RADIATOR SUPPORT SEAL

  1. Remove the 7 clips and radiator support seal.

    B180890E02


2. REMOVE RADIATOR GRILLE

B180899E01
  1. Put protective tape around the radiator grille.

  1. Remove the 3 screws.

  1. Detach the 2 clips and 8 claws, and remove the radiator grille.


3. REMOVE FRONT BUMPER COVER

HINT:
For the front bumper cover with garnish, use the procedures described below.

  1. Put protective tape around the bumper cover.

    B180993E01

  1. Using a T30 "TORX" socket, remove the 6 screws.

    B180994E01

  1. Remove the 3 clips, 4 screws and 4 bolts.

  1. w/o TOYOTA Parking Assist-sensor System, w/o Fog Light:
    Detach the 10 claws and remove the bumper cover.

  1. w/ TOYOTA Parking Assist-sensor System or w/ Fog Light:
    Detach the 10 claws, disconnect the No. 4 engine room wire connector and remove the bumper cover.

    B180995

  1. B181927
    w/ Headlight Cleaner System:
    Disconnect the headlight cleaner hose and remove the bumper cover.


4. REMOVE TRANSMISSION OIL COOLER AIR DUCT

  1. A174154
    Remove the 4 bolts and oil cooler air duct.


5. DISCONNECT RADIATOR SIDE DEFLECTOR LH

  1. A174322
    Using a clip remover, remove the 4 clips and disconnect the side deflector.


6. REMOVE FRONT FENDER SPLASH SHIELD SUB-ASSEMBLY LH

B180991
  1. Remove the 3 bolts and screw.

  1. Turn the clip indicated by the arrow in the illustration to remove the fender splash shield.


7. REMOVE FRONT FENDER SPLASH SHIELD SUB-ASSEMBLY RH

HINT:
Use the same procedures described for the LH side.


8. REMOVE NO. 1 ENGINE UNDER COVER SUB-ASSEMBLY

  1. A238241
    Remove the 10 bolts and No. 1 engine under cover.


9. DRAIN ENGINE COOLANT

CAUTION:
Do not remove the radiator cap while the engine and radiator are still hot. Pressurized, hot engine coolant and steam may be released and cause serious burns.

  1. Loosen the radiator drain cock plug.

    HINT:
    Collect the coolant in a container and dispose of it according to the regulations in your area.

  1. Remove the radiator cap. Then drain the coolant from the radiator.

  1. Loosen the 2 cylinder block drain cock plugs. Then drain the coolant from the engine.

  1. Tighten the 2 cylinder block drain cock plugs.

    Torque:
    13 N*m{ 133 kgf*cm , 10 ft.*lbf }


    A174123E02
    Text in Illustration 
    *1
    Radiator Reservoir
    *2
    Radiator Cap
    *3
    Radiator Drain Cock Plug
    *4
    Cylinder Block Drain Cock Plug

  1. Tighten the radiator drain cock plug by hand.


10. REMOVE V-BANK COVER SUB-ASSEMBLY

  1. A174196E03
    Raise the front of the V-bank cover to detach the 3 pins. Then remove the 2 V-bank cover hooks from the bracket, and remove the V-bank cover.
    Text in Illustration 
    *1
    Bracket
    *2
    Hook
    *3
    Pin
    *4
    Grommet


11. REMOVE AIR CLEANER HOSE ASSEMBLY

  1. A243375
    Disconnect the vacuum hose and No. 2 ventilation hose.

  1. Loosen the 2 hose clamps.

  1. Remove the air cleaner hose.


12. REMOVE NO. 1 RADIATOR HOSE

13. REMOVE NO. 2 RADIATOR HOSE

14. REMOVE FAN SHROUD

  1. A151842
    Loosen the 4 nuts holding the fluid coupling fan.

  1. Remove the fan and generator V-belt (Click here).

  1. A238869
    Disconnect the reservoir hose from the upper radiator tank.

  1. Detach the claw to open the flexible hose clamp.

  1. Remove the 2 bolts and disconnect the oil cooler tube from the fan shroud.

  1. Remove the 2 bolts holding the fan shroud.

  1. Remove the 4 nuts of the fluid coupling fan, and then remove the shroud together with the coupling fan.

    NOTICE:
    Be careful not to damage the radiator core.

  1. Remove the fan pulley.


15. REMOVE RADIATOR ASSEMBLY

  1. A174209
    Disconnect the 2 oil cooler hoses.

  1. A174155
    Remove the 4 bolts and radiator.

← ON-VEHICLE INSPECTION (from Sep 2011)REMOVAL (from Jan 2012) →