2011-2013 Land Cruiser · Service Manual Engine / Hybrid / EV System

DISASSEMBLY

Removal / installation · Vehicles built from Sep 2011


1. INSPECT CONNECTING ROD THRUST CLEARANCE

  1. A164562
    Using a dial indicator, measure the thrust clearance while moving the connecting rod back and forth.

    Standard thrust clearance:
    0.14 to 0.54 mm (0.00551 to 0.0213 in.)

    Maximum thrust clearance:
    0.60 mm (0.0236 in.)

    If the thrust clearance is more than the maximum, replace one or more connecting rods as necessary.
    If necessary, replace the crankshaft.


2. REMOVE PISTON SUB-ASSEMBLY WITH CONNECTING ROD

  1. A164635
    Using a ridge reamer, remove all the carbon from the top of the cylinder.

  1. Uniformly loosen the connecting rod bolts, and remove the connecting rod cap with bearing.

  1. Push out the piston and connecting rod with bearing through the top of the cylinder block.

    HINT:
    Arrange the piston and connecting rod assemblies in the correct order.


3. REMOVE CONNECTING ROD BEARING

  1. A164871
    Remove the connecting rod and connecting rod cap bearings.

    HINT:
    Arrange the removed parts in the correct order.


4. REMOVE PISTON RING SET

  1. A164601
    Using a piston ring expander, remove the No. 1 and No. 2 compression rings.

  1. Using a piston ring expander, remove the oil ring.

  1. Remove the oil ring expander by hand.

    HINT:
    Arrange the removed parts in the correct order.


5. REMOVE PISTON WITH PIN SUB-ASSEMBLY

  1. A164623
    Check the fitting condition between the piston and piston pin by trying to move the piston back and forth on the piston pin.
    If any movement is felt, replace the piston and pin as a set.

  1. A164602
    Using a screwdriver, pry out the 2 snap rings.

  1. A164823E01
    Gradually heat the piston to approximately 80°C (176°F).

  1. A164603
    Using a plastic-faced hammer and brass bar, lightly tap out the piston pin and remove the connecting rod.

    HINT:
    1. The piston and pin are a matched set.
    2. Arrange the piston and connecting rod assemblies in the correct order.


6. CLEAN PISTON

  1. A164604
    Using a gasket scraper, remove the carbon from the piston top.

  1. A164605
    Using a groove cleaning tool or broken ring, clean the piston ring grooves.

  1. A164842
    Using solvent and a brush, thoroughly clean the piston.

    NOTICE:
    Do not use a wire brush.


7. INSPECT CRANKSHAFT THRUST CLEARANCE

  1. A164572
    Using a dial indicator, measure the thrust clearance while prying the crankshaft back and forth with a screwdriver.

    Standard thrust clearance:
    0.02 to 0.22 mm (0.000787 to 0.00866 in.)

    Maximum thrust clearance:
    0.30 mm (0.0118 in.)

    If the thrust clearance is more than the maximum, replace the thrust washers as a set.

    Standard thrust washer thickness:
    2.44 to 2.49 mm (0.0961 to 0.0980 in.)

    If necessary, replace the crankshaft.


8. REMOVE CRANKSHAFT

  1. A164796E01
    Using several steps, loosen and remove the 10 crankshaft bearing cap set bolts uniformly in the sequence shown in the illustration.

  1. A164797E01
    Using several steps, loosen and remove the 20 crankshaft bearing cap set bolts uniformly in the sequence shown in the illustration.

  1. A164799
    Remove the 2 cylinder block stiffening plates.

  1. A164847
    Using 2 crankshaft bearing cap set bolts, pull out the 5 bearing caps.

    NOTICE:
    Take care not to damage the contact surfaces of the crankshaft bearing cap and cylinder block.

    HINT:
    1. Keep the lower bearing and crankshaft bearing cap as a set.
    2. Arrange the crankshaft bearing caps in the correct order.

  1. A164570
    Remove the crankshaft.


9. REMOVE CRANKSHAFT THRUST WASHER SET

A164600

10. REMOVE CRANKSHAFT BEARING

A164798E01

HINT:
  1. Keep the upper and lower crankshaft bearings and crankshaft bearing cap as a set.
  2. Arrange the crankshaft bearing caps and bearings in the correct order.


11. REMOVE NO. 1 OIL NOZZLE SUB-ASSEMBLY

  1. A164571
    Using a 5 mm hexagon wrench, remove the 4 bolts and 4 oil nozzles.


12. INSPECT INPUT SHAFT BEARING (for Manual Transmission)
  1. Turn the bearing by hand.
    If the bearing is stuck or difficult to turn, replace the input shaft bearing. For removal procedures, refer to the following (Click here) and for installation procedures, refer to the following (Click here).

    HINT:
    The bearing is permanently lubricated and requires no cleaning or lubrication.


13. REMOVE CYLINDER BLOCK STRAIGHT SCREW PLUG

  1. A177329E01
    Remove the 2 straight screw plugs and 2 gaskets.

← COMPONENTS (from Sep 2011)INSPECTION (from Sep 2011) →