2011-2013 Land Cruiser · Service Manual Engine / Hybrid / EV System

DISASSEMBLY

Removal / installation · Vehicles built from Jan 2012

Versions by build date: Sep 2011 – Dec 2011 from Jan 2012


1. REMOVE OIL PRESSURE SENDER GAUGE ASSEMBLY

  1. A270150
    Disconnect the oil pressure switch connector.

  1. Remove the oil pressure switch.


2. REMOVE ENGINE COOLANT TEMPERATURE SENSOR

A224780
  1. Disconnect the sensor connector.

  1. Using a 19 mm deep socket wrench, remove the engine coolant temperature sensor.

  1. Remove the gasket from the engine coolant temperature sensor.


3. REMOVE CYLINDER BLOCK WATER DRAIN COCK SUB-ASSEMBLY

  1. for Type A:

    1. A221157
      Remove the 2 cylinder block water drain cock plugs from the 2 cylinder block water drain cocks.

    2. Remove the 2 cylinder block water drain cocks from the cylinder block.

  1. for Type B:

    1. A273790
      Remove the cylinder block water drain cock plug from the cylinder block water drain cock.

    2. Remove the cylinder block water drain cock from the cylinder block.


4. REMOVE VVT SENSOR (for Intake Side of Bank 1)

  1. A221424
    Disconnect the VVT sensor connector.

  1. Remove the bolt and VVT sensor.


5. REMOVE VVT SENSOR (for Exhaust Side of Bank 1)

  1. A221425
    Disconnect the VVT sensor connector.

  1. Remove the bolt and VVT sensor.


6. REMOVE VVT SENSOR (for Intake Side of Bank 2)

  1. A221426
    Disconnect the VVT sensor connector.

  1. Remove the bolt and VVT sensor.


7. REMOVE VVT SENSOR (for Exhaust Side of Bank 2)

  1. A221427
    Disconnect the VVT sensor connector.

  1. Remove the bolt and VVT sensor.


8. REMOVE CRANKSHAFT POSITION SENSOR

  1. A076417E01
    Disconnect the sensor connector.

  1. Remove the bolt and crankshaft position sensor.


9. REMOVE CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY (for Intake Side of Bank 1)

  1. A221417
    Disconnect the camshaft timing oil control valve connector.

  1. Remove the bolt and camshaft timing oil control valve.

  1. Remove the O-ring from the camshaft timing oil control valve.


10. REMOVE CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY (for Exhaust Side of Bank 1)

  1. A221416
    Disconnect the camshaft timing oil control valve connector.

  1. Remove the bolt and camshaft timing oil control valve.

  1. Remove the O-ring from the camshaft timing oil control valve.


11. REMOVE CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY (for Intake Side of Bank 2)

  1. A221418
    Disconnect the camshaft timing oil control valve connector.

  1. Remove the bolt and camshaft timing oil control valve.

  1. Remove the O-ring from the camshaft timing oil control valve.


12. REMOVE CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY (for Exhaust Side of Bank 2)

  1. A272720
    Disconnect the camshaft timing oil control valve connector.

  1. Remove the bolt and camshaft timing oil control valve.

  1. Remove the O-ring from the camshaft timing oil control valve.


13. REMOVE OIL FILLER CAP HOUSING

  1. A221161
    Remove the oil filler cap.

  1. Remove the 2 nuts, oil filler cap housing and gasket.


14. REMOVE NO. 1 OIL PIPE

  1. A223691
    Remove the 2 oil pipe unions, oil control valve filter LH, 3 gaskets and No. 1 oil pipe.

    NOTICE:
    Do not touch the mesh when removing the oil control valve filter.


15. REMOVE NO. 2 OIL PIPE

  1. A223692
    Remove the 2 oil pipe unions, oil control valve filter RH, 3 gaskets and No. 2 oil pipe.

    NOTICE:
    Do not touch the mesh when removing the oil control valve filter.


16. REMOVE OIL FILTER ELEMENT

  1. A094910E09
    Connect a hose with an inside diameter of 15 mm (0.591 in.) to the pipe.
    Text in Illustration 
    *1
    Pipe
    *2
    Hose

  1. A222100
    Remove the oil filter drain plug.

  1. A272717E01
    Install the pipe to the oil filter cap.
    Text in Illustration 
    *1
    Cap
    *2
    Valve
    *3
    Pipe
    *4
    O-Ring
    *5
    Hose

    NOTICE:
    If the O-ring is removed with the drain plug, install the O-ring together with the pipe.

    HINT:
    Use a container to catch the draining oil.

  1. A222102
    Check that oil is drained from the oil filter. Then, disconnect the pipe and remove the O-ring as shown in the illustration.

  1. A222103E01
    Using SST, remove the oil filter cap.
    SST
    09228-06501  
    Text in Illustration 
    *1
    Oil Filter Bracket Clip

    NOTICE:
    Do not remove the oil filter bracket clip.

  1. A153538E03
    Remove the oil filter element and O-ring from the oil filter cap.
    Text in Illustration 
    *1
    O-Ring

    NOTICE:
    Be sure to remove the O-ring (for the cap) by hand, without using any tools, to prevent damage to the groove for the O-ring in the cap.


17. REMOVE OIL FILTER BRACKET

  1. A268548
    Remove the 2 nuts, bolt, oil filter bracket and gasket.


18. REMOVE WATER INLET HOUSING
  1. Disconnect the throttle body connector.

  1. A273503
    Disconnect the 5 water by-pass hoses.

  1. Disconnect the oil cooler hose.

  1. Disconnect the No. 2 oil cooler hose.

  1. A223012
    Remove the 5 bolts and water inlet.

  1. Remove the O-ring from the water outlet pipe.

  1. Remove the gasket from the water pump.


19. REMOVE REAR WATER BY-PASS JOINT

  1. A076534E01
    Remove the 2 bolts, 4 nuts, rear water by-pass joint and 2 gaskets.

  1. Remove the O-ring from the No. 1 water outlet pipe.


20. REMOVE SPARK PLUG
  1. Remove the 6 spark plugs.


21. REMOVE PCV VALVE SUB-ASSEMBLY
  1. Loosen the hose clamp and disconnect the PCV hose from the valve.

  1. A273470
    Remove the valve.


22. REMOVE CRANKSHAFT PULLEY

  1. A072947E04
    Using SST, hold the crankshaft pulley and loosen the pulley bolt. Continue to loosen the bolt until only 2 or 3 threads are screwed into the crankshaft.
    SST
    09213-54015   (91651-60855)
    09330-00021  

  1. A072948E02
    Using the pulley set bolt and SST, remove the crankshaft pulley and pulley bolt.
    SST
    09950-50013   (09951-05010, 09952-05010, 09953-05020, 09954-05031)


23. REMOVE CYLINDER HEAD COVER SUB-ASSEMBLY LH

  1. A226542
    Remove the 12 bolts, seal washer, cylinder head cover and gasket.

    HINT:
    Make sure the removed parts are returned to the same places they were removed from.

  1. A223665
    Remove the 3 gaskets.


24. REMOVE CYLINDER HEAD COVER SUB-ASSEMBLY

  1. A226543
    Remove the 12 bolts, seal washer, cylinder head cover and gasket.

    HINT:
    Make sure the removed parts are returned to the same places they were removed from.

  1. A221164
    Remove the 3 gaskets.


25. REMOVE SPARK PLUG TUBE GASKET

A124195
  1. Bend the ventilation baffle plate claws on the cylinder head cover to an angle of 90° or more.

    Text in Illustration 
    V100135
    Pry

  1. Remove the 6 spark plug tube gaskets.

    HINT:
    Be careful not to damage the gasket when removing it as the removed gasket needs to be used when installing a new one.


26. REMOVE ENGINE OIL LEVEL SENSOR
  1. Disconnect the connector.

  1. A221160
    Remove the 4 bolts and sensor.

  1. A216760E01
    Cut away part of the gasket and remove the gasket from the engine oil level sensor.
    Text in Illustration 
    *1
    Cutting Position
    *2
    Supply Part

    HINT:
    Remove only the outer part of the gasket.


27. REMOVE OIL PAN DRAIN PLUG
  1. Remove the drain plug and gasket.


28. REMOVE NO. 2 OIL PAN SUB-ASSEMBLY

  1. A174340
    Remove the 10 bolts and 2 nuts.

    HINT:
    Make sure the removed parts are returned to the same places they were removed from.

  1. A174341E02
    Insert the blade of an oil pan seal cutter between the oil pans. Cut through the applied sealer and remove the No. 2 oil pan.
    Text in Illustration 
    *1
    Oil Pan Seal Cutter

    NOTICE:
    Be careful not to damage the contact surfaces of the oil pans.


29. REMOVE OIL STRAINER SUB-ASSEMBLY

  1. A239204
    Remove the 2 nuts and oil strainer.


30. REMOVE OIL PAN SUB-ASSEMBLY

  1. A222173
    Remove the 17 bolts and 2 nuts.

    HINT:
    Make sure the removed parts are returned to the same places they were removed from.

  1. A221168E05
    Using a screwdriver, remove the oil pan by prying between the oil pan and cylinder block as shown in the illustration.
    Text in Illustration 
    *a
    LH Side
    *b
    RH Side
    *c
    Pry

    NOTICE:
    Be careful not to damage the contact surfaces of the cylinder block and oil pan.

    HINT:
    Tape the screwdriver tip before use.

  1. A222122
    Remove the 3 O-rings from the timing chain cover.


31. REMOVE NO. 1 OIL PAN BAFFLE PLATE

  1. A224779
    Remove the 6 bolts and No. 1 oil pan baffle plate.


32. REMOVE ENGINE REAR OIL SEAL RETAINER

  1. A076247E04
    Remove the 5 bolts and 2 nuts.

  1. Using a screwdriver, remove the oil seal retainer by prying between the oil seal retainer and crankshaft bearing cap.

    Text in Illustration 
    *a
    Pry

    HINT:
    Tape the screwdriver tip before use.


33. REMOVE REAR CRANKSHAFT OIL SEAL

  1. A076248E03
    Using a screwdriver and hammer, tap out the oil seal.

    NOTICE:
    Be careful not to damage the rear oil seal retainer.


34. REMOVE TIMING CHAIN COVER SUB-ASSEMBLY

  1. A221169
    Remove the 26 bolts and 2 nuts.

  1. A221170
    Remove the timing chain cover by prying between the timing chain cover and cylinder head or cylinder block with a screwdriver.

    NOTICE:
    Be careful not to damage the contact surfaces of the timing chain cover, cylinder block and cylinder head.

    HINT:
    Tape the screwdriver tip before use.

  1. A221404
    Remove the oil pump gasket from the cylinder block.


35. REMOVE ENGINE WATER PUMP ASSEMBLY

  1. A221171
    Remove the 8 bolts, engine water pump and gasket.


36. REMOVE FRONT CRANKSHAFT OIL SEAL
  1. Using a screwdriver and wooden block, pry out the oil seal.

    NOTICE:
    Do not damage the surface of the oil seal press fit hole.

    HINT:
    Tape the screwdriver tip before use.


37. SET NO. 1 CYLINDER TO TDC/COMPRESSION
  1. Temporarily install the pulley set bolt.

  1. A222172E01
    Turn the crankshaft clockwise to align the timing mark on the crank angle sensor plate with the RH block bore center line (TDC/compression).
    Text in Illustration 
    *1
    Center Line
    *2
    Timing Mark
    *3
    Sensor Plate

  1. A225378E01
    Check that the timing marks of the camshaft timing gears are aligned with the timing marks of the bearing caps as shown in the illustration.
    If not, turn the crankshaft clockwise 1 revolution (360°) and align the timing marks as above.
    Text in Illustration 
    *1
    Timing Mark


38. REMOVE NO. 1 CHAIN TENSIONER ASSEMBLY

  1. A124589E05
    Move the stopper plate upward to release the lock, and push the plunger deep into the tensioner.
    Text in Illustration 
    *1
    Plunger
    *2
    Stopper Plate
    *3
    Pin

  1. Move the stopper plate downward to set the lock, and insert a pin with a diameter of 1.27 mm (0.0500 in.) into the stopper plate hole.

  1. A095165E02
    Remove the 2 bolts and No. 1 chain tensioner assembly.


39. REMOVE CHAIN TENSIONER SLIPPER

  1. A223730
    Remove the chain tensioner slipper.


40. REMOVE CHAIN SUB-ASSEMBLY

  1. A221173E01
    Turn the crankshaft counterclockwise 10° to loosen the chain of the crankshaft timing sprocket.
    Text in Illustration 
    *1
    Center Line
    *2
    Timing Mark
    *3
    Sensor Plate

  1. Remove the pulley set bolt.

  1. A221174
    Remove the chain sub-assembly from the crankshaft timing sprocket and place it on the crankshaft.

  1. A095682E12
    Turn the camshaft timing gear assembly on bank 1 clockwise approximately 60° so that it is as shown in the illustration. Be sure to loosen the chain sub-assembly between the banks.

  1. Remove the chain sub-assembly.

    Text in Illustration 
    *A
    for Bank 1


41. REMOVE NO. 1 IDLE GEAR SHAFT

  1. A221175
    Using a 10 mm hexagon wrench, remove the No. 2 idle gear shaft, No. 1 idle gear and No. 1 idle gear shaft.


42. REMOVE NO. 1 CHAIN VIBRATION DAMPER

  1. A223642
    Remove the 2 bolts and No. 1 chain vibration damper.


43. REMOVE NO. 2 CHAIN VIBRATION DAMPER

  1. A221176
    Remove the 2 No. 2 chain vibration dampers.


44. REMOVE CRANKSHAFT TIMING SPROCKET

  1. A158530E01
    Remove the crankshaft timing sprocket.


45. REMOVE CAMSHAFT TIMING GEARS AND NO. 2 CHAIN (for Bank 1)

  1. A221132E01
    While raising the No. 2 chain tensioner assembly, insert a pin with a diameter of 1.0 mm (0.0394 in.) into the hole to hold the No. 2 chain tensioner assembly.
    Text in Illustration 
    *1
    Pin
    *2
    Plunger
    *a
    Push

  1. A221177E01
    Using SST to hold the hexagonal portion of each camshaft, loosen the bolts of the camshaft timing gear assembly and camshaft timing exhaust gear assembly.
    SST
    09922-10010  
    Text in Illustration 
    *a
    Turn
    *b
    Hold

    NOTICE:
    Do not loosen the other 4 bolts. If any of the 4 bolts is loosened, replace the camshaft timing gear assembly and/or camshaft timing exhaust gear assembly with a new one.

  1. Remove the 2 bolts and camshaft timing gear assembly together with the No. 2 chain.


46. REMOVE NO. 2 CHAIN TENSIONER ASSEMBLY

  1. A221178
    Remove the bolt and No. 2 chain tensioner assembly.


47. REMOVE CAMSHAFT BEARING CAP (for Bank 1)

  1. A129700E06
    Check that the camshafts are positioned as shown in the illustration.
    Text in Illustration 
    *1
    Knock Pin
    *a
    Front View

  1. A221179E01
    Uniformly loosen and remove the 8 bearing cap bolts in several steps in the sequence shown in the illustration.

  1. A221180E01
    Uniformly loosen and remove the 12 bearing cap bolts in several steps in the sequence shown in the illustration.

    NOTICE:
    Uniformly loosen the bolts while keeping the camshaft level.

  1. Remove the 5 camshaft bearing caps.

  1. Remove the camshaft and No. 2 camshaft.


48. REMOVE CAMSHAFT HOUSING SUB-ASSEMBLY RH

  1. A221181E01
    Remove the camshaft housing sub-assembly RH by prying between the cylinder head and camshaft housing sub-assembly RH with a screwdriver.
    Text in Illustration 
    *1
    Protective Tape

    NOTICE:
    Be careful not to damage the contact surfaces of the cylinder head and camshaft housing sub-assembly RH.

    HINT:
    Tape the screwdriver tip before use.


49. REMOVE CAMSHAFT TIMING GEARS AND NO. 2 CHAIN (for Bank 2)

  1. A221182E01
    While pushing down the No. 3 chain tensioner assembly, insert a pin with a diameter of 1.0 mm (0.0394 in.) into the hole to hold the No. 3 chain tensioner assembly.
    Text in Illustration 
    *1
    Pin
    *2
    Plunger
    *a
    Push

  1. A223637E01
    Using SST to hold the hexagonal portion of each camshaft, loosen the bolts of the camshaft timing gear assembly and camshaft timing exhaust gear assembly.
    SST
    09922-10010  
    Text in Illustration 
    *a
    Turn
    *b
    Hold

    NOTICE:
    Do not loosen the other 4 bolts. If any of the 4 bolts is loosened, replace the camshaft timing gear assembly and/or camshaft timing exhaust gear assembly with a new one.

  1. Remove the 2 bolts and camshaft timing gear together with the No. 2 chain.


50. REMOVE NO. 3 CHAIN TENSIONER ASSEMBLY

  1. A221183
    Remove the bolt and No. 3 chain tensioner assembly.


51. REMOVE CAMSHAFT BEARING CAP (for Bank 2)

  1. A223636E01
    Check that the camshafts are positioned as shown in the illustration.
    Text in Illustration 
    *1
    Knock Pin
    *a
    Front View

  1. A221184E01
    Uniformly loosen and remove the 8 bearing cap bolts in several steps in the sequence shown in the illustration.

  1. A221185E01
    Uniformly loosen and remove the 13 bearing cap bolts in several steps in the sequence shown in the illustration.

    NOTICE:
    Uniformly loosen the bolts while keeping the camshaft level.

  1. Remove the 5 camshaft bearing caps.

  1. Remove the No. 3 camshaft and No. 4 camshaft.


52. REMOVE CAMSHAFT HOUSING SUB-ASSEMBLY LH

  1. A221186E01
    Remove the camshaft housing sub-assembly LH by prying between the cylinder head and camshaft housing sub-assembly LH with a screwdriver.
    Text in Illustration 
    *1
    Protective Tape

    NOTICE:
    Be careful not to damage the contact surfaces of the cylinder head and camshaft housing sub-assembly LH.

    HINT:
    Tape the screwdriver tip before use.


53. REMOVE NO. 1 VALVE ROCKER ARM SUB-ASSEMBLY
  1. Remove the 24 valve rocker arms from the cylinder head.

    HINT:
    Arrange the removed parts in the correct order.


54. REMOVE VALVE LASH ADJUSTER ASSEMBLY
  1. Remove the 24 valve lash adjusters from the cylinder head.

    HINT:
    Arrange the removed parts in the correct order.


55. REMOVE VALVE STEM CAP
  1. Remove the 24 valve stem caps from the cylinder head.

    HINT:
    Arrange the removed parts in the correct order.


56. REMOVE CYLINDER HEAD SUB-ASSEMBLY

  1. A221092E01
    Using a 10 mm bi-hexagon wrench, uniformly loosen the 8 cylinder head bolts in the sequence shown in the illustration. Remove the 8 cylinder head bolts and plate washers.

    NOTICE:
    1. Be careful not to drop washers into the cylinder head sub-assembly.
    2. Cylinder head warpage or cracking could result from removing bolts in an incorrect order.

    HINT:
    Arrange the removed parts in the correct order.

  1. Remove the cylinder head sub-assembly.


57. REMOVE CYLINDER HEAD LH

  1. A221093E01
    Uniformly loosen and remove the 2 bolts in several steps in the sequence shown in the illustration.

  1. A221094E01
    Using a 10 mm bi-hexagon wrench, uniformly loosen the 8 bolts in the sequence shown in the illustration. Remove the 8 cylinder head bolts and plate washers.

    NOTICE:
    1. Be careful not to drop washers into the cylinder head sub-assembly.
    2. Cylinder head warpage or cracking could result from removing bolts in an incorrect order.

    HINT:
    Be sure to keep the removed parts for each installation position separate.

  1. Remove the cylinder head LH.


58. REMOVE CYLINDER HEAD GASKET

59. REMOVE NO. 2 CYLINDER HEAD GASKET

60. REMOVE NO. 1 WATER OUTLET PIPE

  1. A227937
    Detach the 3 wire harness clamps.

  1. Remove the 2 nuts, bolt and water outlet pipe.


61. REMOVE KNOCK CONTROL SENSOR

  1. A075662
    Disconnect the 2 sensor connectors.

  1. Remove the 2 bolts and 2 sensors.


62. REMOVE CYLINDER BLOCK WATER JACKET SPACER

A225372
  1. Remove the 2 water jacket spacers from the cylinder head.

    NOTICE:
    Be sure to remove the water jacket spacers. If not, they may fall and become damaged when the cylinder block is inverted.


63. REMOVE TAPER SCREW PLUG

NOTICE:
It is not necessary to remove a taper screw plug unless it is being replaced.


64. REMOVE STRAIGHT PIN

NOTICE:
It is not necessary to remove a straight pin unless it is being replaced.


65. REMOVE RING PIN

NOTICE:
It is not necessary to remove a ring pin unless it is being replaced.


66. REMOVE STUD BOLT

NOTICE:
It is not necessary to remove a stud bolt unless it is being replaced.

← DISASSEMBLY (Sep 2011 – Dec 2011)INSPECTION (Sep 2011 – Dec 2011) →