2011-2013 Land Cruiser · Service Manual Engine / Hybrid / EV System

DISASSEMBLY

Removal / installation · Vehicles built Sep 2011 – Dec 2011

Versions by build date: Sep 2011 – Dec 2011 from Jan 2012


1. REMOVE OIL PRESSURE SENSOR

  1. A175289
    Using a 24 mm deep socket wrench, remove the oil pressure sensor.


2. REMOVE ENGINE COOLANT TEMPERATURE SENSOR

  1. A175290
    Remove the engine coolant temperature sensor and gasket.


3. REMOVE CYLINDER BLOCK WATER DRAIN COCK SUB-ASSEMBLY

  1. A158568
    Remove the 2 water drain cocks.


4. REMOVE VVT SENSOR

  1. A158546E02
    Remove the 2 bolts and 2 VVT sensors from the cylinder head LH and RH.


5. REMOVE CRANKSHAFT POSITION SENSOR

  1. A158545
    Remove the bolt and crankshaft position sensor.


6. REMOVE CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY RH

  1. A158547E02
    Remove the bolt and camshaft timing oil control valve from the cylinder head.

  1. Remove the O-ring.


7. REMOVE CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY LH
  1. Remove the bolt and camshaft timing oil control valve from the cylinder head.

  1. Remove the O-ring.


8. REMOVE OIL CONTROL VALVE FILTER

  1. A072942E06
    Remove the 2 unions, 2 filters and 2 gaskets from the cylinder head LH and RH.


9. REMOVE OIL FILTER SUB-ASSEMBLY
  1. Remove the drain pipe cap.

  1. A174331E01
    Using SST, remove the oil filter.
    SST
    09228-07501  

    HINT:
    1. Put the disposal container beneath the drain hose to collect the oil from the oil filter cover.
    2. Drain hose inside diameter: 8 mm (0.315 in.)
    3. Drain hose length: 900 mm (2.95 ft.)


10. REMOVE OIL COOLER ASSEMBLY

  1. A174351
    Remove the oil cooler hose and No. 2 oil cooler hose.

  1. A174352
    Remove the union bolt, plate washer and oil cooler.

  1. Remove the O-ring from the oil cooler.


11. REMOVE OIL FILTER BRACKET SUB-ASSEMBLY

  1. A151244
    Remove the 3 bolts, 2 nuts, oil filter bracket and O-ring.


12. DISCONNECT NO. 1 WATER BY-PASS HOSE

13. DISCONNECT NO. 2 WATER BY-PASS HOSE

14. DISCONNECT NO. 3 WATER BY-PASS HOSE

15. REMOVE WATER INLET HOUSING

  1. A076337E01
    Remove the 5 bolts and water inlet housing.

  1. Remove the O-ring and gasket from the water outlet pipe and water pump.


16. REMOVE REAR WATER BY-PASS JOINT

  1. A076534E01
    Remove the 2 bolts, 4 nuts, rear water by-pass joint and 2 gaskets.

  1. Remove the O-ring from the No. 1 water outlet pipe.


17. REMOVE OIL FILLER CAP SUB-ASSEMBLY

A158574

18. REMOVE OIL FILLER CAP HOUSING
  1. Remove the 2 nuts, oil filler cap housing and gasket.


19. REMOVE SPARK PLUG
  1. Remove the 6 spark plugs.


20. REMOVE CYLINDER HEAD COVER SUB-ASSEMBLY RH

  1. A072943E01
    Remove the 10 bolts, 3 seal washers, 2 nuts, cylinder head cover and gasket.


21. REMOVE VENTILATION VALVE SUB-ASSEMBLY
  1. Remove the ventilation valve.


22. REMOVE CYLINDER HEAD COVER SUB-ASSEMBLY LH

  1. A072944E01
    Remove the 10 bolts, 3 seal washers, 2 nuts, cylinder head cover and gasket.


23. REMOVE CRANKSHAFT PULLEY

  1. A072945E01
    Turn the crankshaft pulley, and align the notch with the timing mark "0" of the timing chain cover.

  1. G038065E10
    Check that the timing marks of the camshaft timing gears and sprockets are aligned with the timing marks of the bearing caps as shown in the illustration.

  1. A072947E03
    Using SST, hold the crankshaft pulley and loosen the pulley set bolt.
    SST
    09213-54015   (91651-60855)
    09330-00021  

  1. A072948E01
    Using the pulley set bolt and SST, remove the crankshaft pulley.
    SST
    09950-50013   (09951-05010, 09952-05010, 09953-05020, 09954-05030)


24. REMOVE OIL PAN DRAIN PLUG
  1. Remove the drain plug and gasket.


25. REMOVE NO. 2 OIL PAN SUB-ASSEMBLY

  1. A174340E01
    Remove the 10 bolts and 2 nuts.

  1. A174341E01
    Insert the blade of an oil pan seal cutter between the oil pans. Cut through the applied sealer and remove the No. 2 oil pan.


26. REMOVE OIL STRAINER SUB-ASSEMBLY

  1. A264937
    Remove the 2 nuts, oil strainer and gasket.


27. REMOVE OIL PAN SUB-ASSEMBLY

  1. A174343E01
    Remove the 17 bolts (A, B, C) and 2 nuts.

  1. A174344E01
    Using a screwdriver, remove the oil pan by prying between the oil pan and cylinder block as shown in the illustration.

    NOTICE:
    Be careful not to damage the contact surfaces of the cylinder block and oil pan.

  1. A076306E01
    Remove the O-ring from the timing chain cover.

  1. Remove the 4 stud bolts from the oil pan.


28. REMOVE ENGINE REAR OIL SEAL RETAINER

  1. A076247E02
    Remove the 5 bolts and 2 nuts.

  1. Using a screwdriver, remove the oil seal retainer by prying between the oil seal retainer and crankshaft bearing cap.


29. REMOVE REAR CRANKSHAFT OIL SEAL

  1. A076248E03
    Using a screwdriver and hammer, tap out the oil seal.

    NOTICE:
    Be careful not to damage the rear oil seal retainer.


30. REMOVE TIMING CHAIN COVER SUB-ASSEMBLY

  1. A174345E01
    Remove the 24 bolts labeled A and B, and the 2 nuts.

  1. G038102E01
    Remove the timing chain cover by prying between the timing chain cover and cylinder head or cylinder block with a screwdriver.

    NOTICE:
    Be careful not to damage the contact surfaces of the timing chain cover, cylinder block and cylinder head.

  1. Remove the O-ring from the cylinder head LH side.


31. REMOVE WATER PUMP ASSEMBLY

  1. A179596
    Remove the 8 bolts, water pump and gasket.


32. REMOVE FRONT CRANKSHAFT OIL SEAL
  1. If the timing chain case is removed:

    1. Using a screwdriver and wooden block, pry out the oil seal.

      HINT:
      Tape the screwdriver tip before use.

      NOTICE:
      Do not damage the surface of the oil seal press fit hole and crankshaft.


33. REMOVE NO. 1 CHAIN TENSIONER ASSEMBLY

NOTICE:
  1. Never rotate the crankshaft with the chain tensioner removed.
  2. When rotating the camshaft with the timing chain removed, rotate the crankshaft counterclockwise 40° from the TDC first.

  1. A158627E01
    While turning the stopper plate of the tensioner clockwise, push in the plunger of the chain tensioner as shown in the illustration.

  1. While turning the stopper plate of the tensioner counterclockwise, insert a bar of φ3.5 mm (0.138 in.) into the holes on the stopper plate and tensioner to fix the stopper plate in place.

  1. Remove the 2 bolts and chain tensioner.


34. REMOVE CHAIN TENSIONER SLIPPER
  1. Remove the chain tensioner slipper.


35. REMOVE NO. 1 IDLE GEAR SHAFT

  1. A072959E01
    Using a 10 mm hexagon wrench, remove the No. 2 idle gear shaft, No. 1 idle gear and No. 1 idle gear shaft.


36. REMOVE NO. 2 CHAIN VIBRATION DAMPER

  1. G036844E01
    Remove the 2 No. 2 chain vibration dampers.


37. REMOVE NO. 1 CHAIN SUB-ASSEMBLY
  1. Remove the No. 1 chain.


38. REMOVE CRANKSHAFT TIMING SPROCKET

  1. A158530
    Remove the crankshaft timing sprocket.


39. REMOVE NO. 1 CHAIN VIBRATION DAMPER

  1. A076292E01
    Remove the 2 bolts and No. 1 chain vibration damper.


40. REMOVE CAMSHAFT TIMING GEARS AND NO. 2 CHAIN (for Bank 1)

  1. G038067E01
    While raising the No. 2 chain tensioner, insert a pin of φ1.0 mm (0.0394 in.) into the hole to fix the tensioner in place.

  1. G038110E01
    Hold the hexagonal portion of the camshaft with a wrench, and remove the 2 bolts, camshaft timing gear, camshaft timing sprocket and No. 2 chain.

    NOTICE:
    1. Be careful not to damage the cylinder head and valve lifter with the wrench.
    2. Do not disassemble the camshaft timing gear.


41. REMOVE NO. 2 CHAIN TENSIONER ASSEMBLY

  1. A072962E01
    Remove the bolt and No. 2 chain tensioner.


42. REMOVE CAMSHAFT TIMING GEARS AND NO. 2 CHAIN (for Bank 2)

  1. G038075E01
    While raising the No. 3 chain tensioner, insert a pin of φ1.0 mm (0.0394 in.) into the hole to fix the tensioner in palace.

  1. G038112E01
    Hold the hexagonal portion of the camshaft with a wrench, and remove the 2 bolts, camshaft timing gear, camshaft timing sprocket and No. 2 chain.

    NOTICE:
    1. Be careful not to damage the cylinder head and valve lifter with the wrench.
    2. Do not disassemble the camshaft timing gear.


43. REMOVE NO. 3 CHAIN TENSIONER ASSEMBLY

  1. A072965E01
    Remove the bolt and No. 3 chain tensioner.


44. REMOVE NO. 1 CAMSHAFT AND NO. 2 CAMSHAFT (for Bank 1)

NOTICE:
As the thrust clearance of the camshaft is small, the camshaft must be kept level while it is being removed. If the camshaft is not kept level, the portion of the cylinder head which receives the shaft thrust may crack or be damaged, causing the camshaft to seize or break. To avoid this, the following steps should be carried out.

  1. A072966E06
    Remove the No. 1 and No. 2 camshafts.

    1. Rotate the camshafts counterclockwise using a wrench so that the cam lobes of the No. 1 cylinder face each direction as shown in the illustration.

    2. A072967E19
      Uniformly loosen and remove the 16 bearing cap bolts in the sequence shown in the illustration.

    3. Remove the 8 bearing caps and 2 camshafts.


45. REMOVE NO. 1 CAMSHAFT BEARING (for Bank 1)

A158703

46. REMOVE NO. 2 CAMSHAFT BEARING (for Bank 1)

A158539

47. REMOVE NO. 3 CAMSHAFT AND NO. 4 CAMSHAFT (for Bank 2)

  1. A072968E19
    Remove the No. 3 and No. 4 camshafts.

    1. Uniformly loosen and remove the 16 bearing cap bolts in the sequence shown in the illustration.

    2. Remove the 8 bearing caps and 2 camshafts.


48. REMOVE CYLINDER HEADS

  1. A072969E13
    Using a 10 mm bi-hexagon wrench, uniformly loosen the 2 bolts in the sequence shown in the illustration. Remove the 2 cylinder head bolts and plate washers.

  1. A072970E08
    Using a 10 mm bi-hexagon wrench, uniformly loosen the 16 bolts in the sequence shown in the illustration. Remove the 16 cylinder head bolts and plate washers.

    NOTICE:
    1. Be careful not to drop the plate washers into the cylinder head.
    2. Cylinder head warpage or cracking could result from removing bolts in the incorrect order.

  1. A072971E01
    Lift the cylinder head from the dowels on the cylinder block, and place the 2 cylinder heads on wooden blocks on a bench.

    NOTICE:
    Be careful not to damage the contact surfaces of the cylinder head and cylinder block.

    HINT:
    If the cylinder head is difficult to lift off, pry between the cylinder head and cylinder block with a screwdriver.


49. REMOVE CYLINDER HEAD GASKET

50. REMOVE NO. 2 CYLINDER HEAD GASKET

51. REMOVE NO. 1 WATER OUTLET PIPE

  1. A151268
    Remove the 3 bolts and water outlet pipe.


52. REMOVE KNOCK SENSOR

  1. A076270E01
    Remove the 2 bolts and 2 knock sensors.

← REMOVAL (from Jan 2012)DISASSEMBLY (from Jan 2012) →