2011-2013 Land Cruiser · Service Manual Engine / Hybrid / EV System

INSPECTION

Inspection · Vehicles built Sep 2011 – Dec 2011


INSPECT STARTER ASSEMBLY

NOTICE:
The following tests must be done within 3 to 5 seconds to prevent the coil from burning out.

  1. Perform the pull-in test.

    1. A159733E01
      Remove the nut, then disconnect the lead wire from terminal C.

    2. Connect the battery to the starter as shown in the illustration. Check that the clutch pinion gear moves outward.
      If the clutch pinion gear does not move, replace the magnet starter switch assembly.

  1. A159734E01
    Perform the holding test.

    1. With the battery connected as above with the clutch pinion gear out, disconnect the negative (-) lead from terminal C. Check that the pinion gear remains out.
      If the clutch pinion gear returns inward, replace the magnet starter switch assembly.

  1. A159735E01
    Inspect the clutch pinion gear return.

    1. Disconnect the negative (-) lead from the starter housing. Check that the clutch pinion gear returns inward.
      If the clutch pinion gear does not return inward, replace the magnet starter switch assembly.

  1. A159736E02
    Perform the operation test without load.

    1. Connect the lead wire to terminal C.

      Torque:
      5.9 N*m{ 60 kgf*cm , 52 in.*lbf }

    2. Grip the starter in a vise.

    3. Connect the battery and an ammeter to the starter as shown in the illustration.

    4. Check that the starter rotates smoothly and steadily while the pinion gear is moving out. Then measure the current.

      Specified current:
      90 A or less at 11.5 V

      If the result is not as specified, replace the starter assembly.


INSPECT STARTER ARMATURE ASSEMBLY

  1. S000054E07
    Inspect the commutator for an open circuit.

    1. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      Commutator
      Always
      Below 1 Ω

      If the result is not as specified, replace the armature assembly.

  1. S000055E08
    Inspect the commutator for a short circuit.

    1. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      Commutator - Armature core
      Always
      10 kΩ or higher

      If the result is not as specified, replace the armature assembly.

  1. Inspect the commutator circle runout.

    1. A115025
      Place the commutator on V-blocks.

    2. Using a dial indicator, measure the circle runout.

      Maximum circle runout:
      0.05 mm (0.00197 in.)

      If the runout is more than the maximum, correct it with sandpaper (#400) or replace the armature assembly.

  1. A115026
    Using a vernier caliper, measure the commutator diameter.

    Standard diameter:
    30.0 mm (1.18 in.)

    Minimum diameter:
    29.0 mm (1.14 in.)

    If the diameter is less than the minimum, replace the armature assembly.

  1. A115027
    Measure the undercut depth of the commutator.

    Standard undercut depth:
    0.6 mm (0.0236 in.)

    Minimum undercut depth:
    0.2 mm (0.00787 in.)

    If the undercut depth is less than the minimum, increase the depth using a hacksaw blade.


INSPECT STARTER YOKE ASSEMBLY

  1. A139614E02
    Inspect for an open circuit.

    1. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      Terminal C wire - Brushes
      Always
      Below 1 Ω

      If the result is not as specified, replace the starter yoke assembly.

  1. P000299E05
    Inspect for a short circuit.

    1. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      Brushes - Starter yoke body
      Always
      10 kΩ or higher

      If the result is not as specified, replace the starter yoke assembly.


INSPECT BRUSH

  1. A062430E06
    Using a vernier caliper, measure the brush length.

    Standard length:
    15.5 mm (0.610 in.)

    Minimum length:
    8.5 mm (0.335 in.)

    If the length is less than the minimum, replace the brush holder and starter yoke assembly.


INSPECT STARTER BRUSH HOLDER ASSEMBLY

  1. A115033
    Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    Positive brush holder - Negative brush holder
    Always
    10 kΩ or higher

    If the result is not as specified, replace the brush holder assembly.

  1. A115032
    Inspect the load of the brush spring.

    1. Take a pull scale reading immediately after the brush spring separates from the brush.

      Standard spring installed load:
      18 to 24 N (1.8 to 2.4 kgf, 4.0 to 5.3 lbf)

      Minimum spring installed load:
      12 N (1 kgf, 2.7 lbf)

      If the installed load is less than the minimum, replace the brush holder assembly.


INSPECT STARTER CLUTCH SUB-ASSEMBLY

  1. A115056E01
    Check that the starter clutch cannot be rotated counterclockwise, and can be rotated clockwise.
    If the starter clutch is not as specified, replace the starter clutch sub-assembly.

  1. Turn the bearing by hand while applying inward force.
    If resistance is felt or the bearing sticks, replace the starter clutch sub-assembly.


INSPECT MAGNET STARTER SWITCH ASSEMBLY

  1. A115057E03
    Inspect the pull-in coil.

    1. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      Terminal 50 - Terminal C
      Always
      Below 1 Ω

      If the result is not as specified, replace the magnet starter switch assembly.

  1. A115034E03
    Inspect the holding coil.

    1. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      Terminal 50 - Switch body
      Always
      Below 2 Ω

      If the result is not as specified, replace the magnet starter switch assembly.

← DISASSEMBLY (Sep 2011 – Dec 2011)REASSEMBLY (Sep 2011 – Dec 2011) →