2011-2013 Land Cruiser · Service Manual Engine / Hybrid / EV System

INSTALLATION

Removal / installation · Vehicles built Sep 2011 – Dec 2011

Versions by build date: Sep 2011 – Dec 2011 from Jan 2012


1. INSTALL FRONT CRANKSHAFT OIL SEAL

  1. A134551E01
    Using SST and a hammer, tap in a new oil seal until its surface is flush with the timing chain cover edge.
    SST
    09226-10010  

    NOTICE:
    1. Keep the lip free from foreign matter.
    2. Do not tap the oil seal at an angle.

  1. Apply MP grease to the lip of the oil seal.


2. INSTALL TIMING CHAIN COVER SUB-ASSEMBLY
  1. Remove any old packing (FIPG) material and be careful not to drop any oil on the contact surfaces of the timing chain cover, cylinder head and cylinder block.

  1. A134563E01
    Install a new O-ring to the cylinder head for bank 2 as shown in the illustration.

  1. A174347E01
    Apply seal packing as shown in the illustration.

    Seal packing:
    Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent

    Standard seal diameter:
    3.0 to 4.0 mm (0.118 to 0.157 in.)

  1. Apply seal packing in a continuous line to the timing chain cover as shown in the illustration.

    A158650E02

    Seal packing:
    for water related part:
    Toyota Genuine Seal Packing 1282B, Three Bond 1282B or equivalent
    for oil related part:
    Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent

    Standard seal diameter:
    3.5 to 4.5 mm (0.138 to 0.177 in.)

    HINT:
    Water related parts are labeled "B" in the illustration.

    NOTICE:
    1. Install the timing chain cover within 3 minutes after applying seal packing. After installing it, the timing chain cover bolts and nuts must be tightened within 15 minutes. Otherwise the seal packing must be removed and reapplied.
    2. Do not apply seal packing to "A" shown in the illustration.

  1. A076304E03
    Align the keyway of the oil pump drive rotor with the rectangular portion of the crankshaft timing gear, and slide the timing chain cover into place.

  1. A174345E01
    Install the timing chain cover with the 24 bolts labeled A and B, and the 2 nuts. Tighten the bolts and nuts uniformly in several steps.

    Torque:
    23 N*m{ 235 kgf*cm , 17 ft.*lbf }

    NOTICE:
    1. Make sure not to wrap the No. 1 chain and slipper over the timing chain cover seal line.
    2. Install the timing chain cover 15 minutes or more after installing the water pump.

    Standard Bolt:
    Item
    Quantity
    Length
    Bolt A
    9
    25 mm (0.984 in.)
    Bolt B
    15
    55 mm (2.17 in.)

    NOTICE:
    Make sure that there is no oil on the bolt threads.


3. INSTALL OIL FILTER BRACKET SUB-ASSEMBLY
  1. Set a new O-ring to the timing chain cover.

  1. A151244
    Install the oil filter bracket with the 3 bolts and 2 nuts.

    Torque:
    19 N*m{ 194 kgf*cm , 14 ft.*lbf }


4. INSTALL WATER INLET HOUSING

  1. A134567E01
    Apply soapy water to a new O-ring, install it to the water outlet pipe.

  1. Install a new O-ring to the water pump.

  1. Install a new gasket to the water pump.

  1. A134568
    Install the water inlet with the 5 bolts.

    Torque:
    9.0 N*m{ 92 kgf*cm , 80 in.*lbf }


5. INSTALL NO. 2 OIL COOLER HOSE
  1. Install the oil cooler hose.


6. INSTALL OIL COOLER HOSE

  1. A180468
    Install the oil cooler hose.


7. INSTALL OIL PAN SUB-ASSEMBLY
  1. Remove any old packing (FIPG) material and be careful not to drop any oil on the contact surfaces of the cylinder block, rear oil seal retainer and oil pan.

  1. A076306E04
    Install a new O-ring to the timing chain cover.
    Text in Illustration 
    *1
    New O-Ring

  1. A174348E02
    Apply seal packing in a continuous line as shown in the illustration.

    Seal packing:
    Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent

    Standard seal diameter:
    3 to 4 mm (0.118 to 0.157 in.)

    Text in Illustration 
    *1
    Seal Packing

    NOTICE:
    1. Remove any oil from the contact surface.
    2. Install the oil pan within 3 minutes after applying seal packing.
    3. Do not start the engine for at least 2 hours after installing.

  1. A265406
    Install the oil pan with the 17 bolts (A, B and C) and 2 nuts. Tighten the bolts and nuts uniformly in several steps.

    Torque:
    for bolt A, B and nut:
    21 N*m{ 214 kgf*cm , 15 ft.*lbf }
    for bolt C:
    10 N*m{ 102 kgf*cm , 7 ft.*lbf }

    Text in Illustration 
    V100135
    Bolt A
    V100136
    Bolt B
    V100137
    Bolt C
    V100138
    Nut

    Standard Bolt:
    Item
    Quantity
    Length
    A
    6
    25 mm (0.984 in.)
    B
    9
    45 mm (1.77 in.)
    C
    2
    14 mm (0.551 in.)


8. INSTALL OIL STRAINER SUB-ASSEMBLY

  1. A264938E01
    Install a new gasket to the oil strainer.
    Text in Illustration 
    *1
    Groove
    *2
    Protrusion

    HINT:
    Align the protrusion of the gasket with the groove of the oil strainer.

  1. Install the oil strainer with the 2 nuts.

    Torque:
    9.0 N*m{ 92 kgf*cm , 80 in.*lbf }


9. INSTALL NO. 2 OIL PAN SUB-ASSEMBLY

  1. A174349E01
    Apply seal packing in a continuous line as shown in the illustration.

    Seal packing:
    Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent

    Standard seal diameter:
    3 to 4 mm (0.118 to 0.157 in.)

    NOTICE:
    1. Remove any oil from the contact surface.
    2. Install the No. 2 oil pan within 3 minutes after applying seal packing.
    3. Do not start the engine for at least 2 hours after the installation.

  1. A174340E01
    Install the No. 2 oil pan with the 10 bolts and 2 nuts. Tighten the bolts and nuts uniformly in several steps.

    Torque:
    for bolt:
    9.0 N*m{ 92 kgf*cm , 81 in.*lbf }
    for nut:
    10 N*m{ 102 kgf*cm , 7 ft.*lbf }


10. INSTALL CRANKSHAFT PULLEY

  1. A076309E03
    Using SST, install the crankshaft pulley with the pulley set bolt.
    SST
    09213-54015   (91651-60855)
    09330-00021  

    Torque:
    250 N*m{ 2549 kgf*cm , 184 ft.*lbf }


11. INSTALL NO. 1 IDLER PULLEY SUB-ASSEMBLY

  1. A238828
    Install the No. 1 idler pulley with the bolt.

    Torque:
    54 N*m{ 551 kgf*cm , 40 ft.*lbf }

    HINT:
    "DOUBLE" is marked on the No. 1 idler pulley to distinguish it from the No. 2 idler pulley.


12. INSTALL NO. 2 IDLER PULLEY SUB-ASSEMBLY

A238835E01

  1. w/ Pulley Cover Plate:

    1. A191314E01
      Install the idler pulley cover plate, idler pulley and No. 2 idler pulley cover plate with the bolt.

      Torque:
      54 N*m{ 551 kgf*cm , 40 ft.*lbf }

      NOTICE:
      If it is necessary to replace the pulley or either plate, replace the No. 2 idler pulley cover plate, No. 2 idler pulley and idler pulley cover plate as a set with new parts.

  1. w/o Pulley Cover Plate:
    Install the 2 No. 2 idler pulleys with the 2 bolts.

    Torque:
    54 N*m{ 551 kgf*cm , 40 ft.*lbf }


13. INSTALL V-RIBBED BELT TENSIONER ASSEMBLY

  1. A175285E01
    Temporarily install the V-ribbed belt tensioner with the 5 bolts.

  1. Tighten bolt 1 and 2 in numerical order.

    Torque:
    36 N*m{ 367 kgf*cm , 27 ft.*lbf }

  1. Tighten the other bolts.

    Torque:
    36 N*m{ 367 kgf*cm , 27 ft.*lbf }

    Standard Bolt:
    Item
    Length
    A
    70 mm (2.76 in.)
    B
    33 mm (1.30 in.)


14. INSTALL ENGINE OIL LEVEL DIPSTICK GUIDE

  1. A158543E01
    Install a new O-ring to the dipstick guide.

  1. Apply a light coat of engine oil to the O-ring.

  1. Push the dipstick guide end into the guide hole.

  1. Install the dipstick guide with the bolt.

    Torque:
    9.0 N*m{ 92 kgf*cm , 80 in.*lbf }


15. INSTALL CYLINDER HEAD COVER SUB-ASSEMBLY LH
  1. Remove any old packing (FIPG) material and be careful not to drop any oil on the contact surfaces of the cylinder head, timing chain cover and cylinder head cover.

  1. A076311E06
    Apply seal packing as shown in the illustration.

    Seal packing:
    Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent

    Standard seal diameter:
    2 to 3 mm (0.0787 to 0.118 in.)

    NOTICE:
    1. Remove any oil from the contact surface.
    2. Install the head cover within 3 minutes after applying seal packing.
    3. Do not start the engine for at least 2 hours after the installation.

  1. Install a new gasket to the cylinder head cover.

  1. Install the seal washers to the bolts.

  1. A072944E02
    Temporarily install the cylinder head cover with the 10 bolts and 2 nuts. Tighten the bolts and nuts uniformly in several steps.

    Torque:
    for bolt A:
    10 N*m{ 102 kgf*cm , 7 ft.*lbf }
    for bolt B and nut:
    9.0 N*m{ 92 kgf*cm , 80 in.*lbf }


16. INSTALL CYLINDER HEAD COVER SUB-ASSEMBLY
  1. Remove any old packing (FIPG) material and be careful not to drop any oil on the contact surfaces of the cylinder head, timing chain cover and cylinder head cover.

  1. A076310E07
    Apply seal packing as shown in the illustration.

    Seal packing:
    Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent

    Standard seal diameter:
    2 to 3 mm (0.0787 to 0.118 in.)

    NOTICE:
    1. Remove any oil from the contact surface.
    2. Install the head cover within 3 minutes after applying seal packing.
    3. Do not start the engine for at least 2 hours after the installation.

  1. Install a new gasket to the cylinder head cover.

  1. Install the seal washers to the bolts.

  1. A072943E02
    Temporarily install the cylinder head cover with the 10 bolts and 2 nuts. Tighten the bolts and nuts uniformly in several steps.

    Torque:
    for bolt A:
    10 N*m{ 102 kgf*cm , 7 ft.*lbf }
    for bolt B and nut:
    9.0 N*m{ 92 kgf*cm , 80 in.*lbf }


17. INSTALL CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY LH

  1. A185217E01
    Apply a light coat of engine oil to a new O-ring and install it to the oil control valve.

  1. A111700E01
    Install the oil control valve with the bolt.

    Torque:
    10 N*m{ 102 kgf*cm , 7 ft.*lbf }

    NOTICE:
    1. Do not allow foreign matter to contact the oil seal face of the oil control valve (connecting surface with cylinder head).
    2. Be careful that the O-ring is not cracked when installing the oil control valve.

  1. Connect the oil control valve connector.


18. INSTALL CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY RH

  1. A185216E02
    Apply a light coat of engine oil to a new O-ring and install it to the oil control valve.

  1. A111699E01
    Install the oil control valve with the bolt.

    Torque:
    10 N*m{ 102 kgf*cm , 7 ft.*lbf }

    NOTICE:
    1. Do not allow foreign matter to contact the oil seal face of the oil control valve (connecting surface with cylinder head).
    2. Be careful that the O-ring is not cracked when installing the oil control valve.

  1. Connect the camshaft timing oil control valve connector.


19. INSTALL VVT SENSOR (for Bank 2)

  1. A176576
    Apply a light coat of engine oil to the O-ring of the VVT sensor.

    NOTICE:
    1. When reusing the sensor, inspect the O-ring.
    2. If the O-ring has scratches or cuts, replace the sensor.

  1. Install the VVT sensor with the bolt.

    Torque:
    8.0 N*m{ 82 kgf*cm , 71 in.*lbf }

  1. Connect the sensor connector.


20. INSTALL VVT SENSOR (for Bank 1)

  1. A176575
    Apply a light coat of engine oil to the O-ring of the sensor.

    NOTICE:
    1. When reusing the sensor, inspect the O-ring.
    2. If the O-ring has scratches or cuts, replace the sensor.

  1. Install the sensor with the bolt.

    Torque:
    8.0 N*m{ 82 kgf*cm , 71 in.*lbf }

  1. Connect the sensor connector.


21. INSTALL SPARK PLUG
  1. Install the 6 spark plugs.

    Torque:
    20 N*m{ 204 kgf*cm , 15 ft.*lbf }


22. INSTALL IGNITION COIL ASSEMBLY

  1. A175728
    Install the 6 ignition coils with the 6 bolts.

    Torque:
    9.0 N*m{ 92 kgf*cm , 80 in.*lbf }

  1. Connect the 6 ignition coil connectors.


23. INSTALL ENGINE ASSEMBLY
(Click here)
← REASSEMBLY (from Jan 2012)INSTALLATION (from Jan 2012) →