2011-2013 Land Cruiser · Service Manual Engine / Hybrid / EV System

REMOVAL

Removal / installation · Vehicles built Sep 2011 – Dec 2011

Versions by build date: Sep 2011 – Dec 2011 from Jan 2012


1. REMOVE ENGINE ASSEMBLY
  1. Remove the engine assembly (Click here).


2. REMOVE IGNITION COIL ASSEMBLY
  1. Disconnect the 6 ignition coil connectors.

  1. A175728
    Remove the 6 bolts and 6 ignition coils.


3. REMOVE SPARK PLUG
  1. Remove the 6 spark plugs.


4. REMOVE VVT SENSOR (for Bank 1)

  1. A176575
    Disconnect the sensor connector.

  1. Remove the bolt and sensor.


5. REMOVE VVT SENSOR (for Bank 2)

  1. A176576
    Disconnect the sensor connector.

  1. Remove the bolt and sensor.


6. REMOVE CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY RH

A111699E01
  1. Disconnect the oil control valve connector.

  1. Remove the bolt and oil control valve.

  1. Remove the O-ring from the oil control valve.


7. REMOVE CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY LH

A111700E01
  1. Disconnect the oil control valve connector.

  1. Remove the bolt and oil control valve.

  1. Remove the O-ring from the oil control valve.


8. REMOVE CYLINDER HEAD COVER SUB-ASSEMBLY RH

  1. A072943E01
    Remove the 10 bolts, 3 seal washers, 2 nuts, cylinder head cover and gasket.


9. REMOVE CYLINDER HEAD COVER SUB-ASSEMBLY LH

  1. A072944E01
    Remove the 10 bolts, 3 seal washers, 2 nuts, cylinder head cover and gasket.


10. REMOVE ENGINE OIL LEVEL DIPSTICK GUIDE

  1. A175286
    Remove the bolt and dipstick guide.

  1. Remove the O-ring from the dipstick guide.


11. DISCONNECT WATER HOSE SUB-ASSEMBLY (for Automatic Transmission)

  1. A179580
    Remove the 2 bolts and disconnect the 3 water hoses.


12. DISCONNECT WATER HOSE SUB-ASSEMBLY (for Manual Transmission)

  1. A179581E01
    Remove the 2 bolts and disconnect the 2 water hoses.


13. REMOVE REAR WATER BY-PASS JOINT
  1. Disconnect the engine coolant temperature sensor connector.

  1. A076534E01
    Remove the 2 bolts, 4 nuts, rear water by-pass joint and 2 gaskets.

  1. A076535E01
    Remove the O-ring from the No. 1 water outlet pipe.


14. REMOVE OIL CONTROL VALVE FILTER

  1. A072942E06
    Remove the 2 unions, 2 filters and 2 gaskets from the cylinder head LH and RH.


15. REMOVE V-RIBBED BELT TENSIONER ASSEMBLY

  1. A175285
    Remove the 5 bolts and V-ribbed belt tensioner.


16. REMOVE NO. 2 IDLER PULLEY SUB-ASSEMBLY

  1. A191314E01
    w/ Pulley Cover Plate:
    Remove the 2 bolts, 2 No. 2 idler pulley cover plate, 2 idler pulley and 2 idler pulley cover plate.

  1. A076338E01
    w/o Pulley Cover Plate:
    Remove the 2 bolts and 2 No. 2 idler pulleys.


17. REMOVE NO. 1 IDLER PULLEY SUB-ASSEMBLY

  1. A239030
    Remove the bolt and No. 1 idler pulley.


18. REMOVE CRANKSHAFT PULLEY

  1. A072945E01
    Turn the crankshaft pulley, and align the notch with the timing mark "0" of the timing chain cover.

  1. G038065E10
    Check that the timing marks of the camshaft timing gears and sprockets are aligned with the timing marks of the bearing caps as shown in the illustration.

  1. A072947E03
    Using SST, hold the crankshaft pulley and loosen the pulley set bolt.
    SST
    09213-54015   (91651-60855)
    09330-00021  

  1. A072948E01
    Using the pulley set bolt and SST, remove the crankshaft pulley.
    SST
    09950-50013   (09951-05010, 09952-05010, 09953-05020, 09954-05030)


19. REMOVE NO. 2 OIL PAN SUB-ASSEMBLY

  1. A174340E01
    Remove the 10 bolts and 2 nuts.

  1. A174341E01
    Insert the blade of an oil pan seal cutter between the oil pans. Cut through the applied sealer and remove the No. 2 oil pan.


20. REMOVE OIL STRAINER SUB-ASSEMBLY

  1. A264937
    Remove the 2 nuts, oil strainer and gasket.


21. REMOVE OIL PAN SUB-ASSEMBLY

  1. A265404
    Remove the 17 bolts and 2 nuts.

  1. A174344E02
    Using a screwdriver, remove the oil pan by prying between the oil pan and cylinder block as shown in the illustration.
    Text in Illustration 
    *a
    Pry
    *b
    LH Side
    *c
    RH Side

    NOTICE:
    Be careful not to damage the contact surfaces of the cylinder block and oil pan.

  1. A076306E01
    Remove the O-ring from the timing chain cover.


22. REMOVE NO. 2 OIL COOLER HOSE

  1. A180468
    Remove the oil cooler hose.


23. REMOVE OIL COOLER HOSE
  1. Remove the oil cooler hose.


24. REMOVE WATER INLET HOUSING

  1. A076337E01
    Remove the 5 bolts and water inlet housing.

  1. Remove the O-ring and gasket from the water outlet pipe and water pump.


25. REMOVE OIL FILTER BRACKET SUB-ASSEMBLY

  1. A151244
    Remove the 3 bolts, 2 nuts, oil filter bracket and O-ring.


26. REMOVE TIMING CHAIN COVER SUB-ASSEMBLY

  1. A174345E01
    Remove the 24 bolts labeled A and B, and the 2 nuts.

  1. G038102E01
    Remove the timing chain cover by prying between the timing chain cover and cylinder head or cylinder block with a screwdriver.

    NOTICE:
    Be careful not to damage the contact surfaces of the timing chain cover, cylinder block and cylinder head.

  1. Remove the O-ring from the cylinder head LH side.


27. REMOVE FRONT CRANKSHAFT OIL SEAL
  1. If the timing chain case is removed:

    1. Using a screwdriver and wooden block, pry out the oil seal.

      HINT:
      Tape the screwdriver tip before use.

      NOTICE:
      Do not damage the surface of the oil seal press fit hole and crankshaft.


28. SET NO. 1 CYLINDER TO TDC/COMPRESSION

  1. A076530E01
    Turn the crankshaft pulley, and align its groove with the timing mark "0" of the timing chain cover.

  1. G038065E10
    Check that the timing marks of the camshaft timing gears and sprockets are aligned with the timing marks of the bearing caps as shown in the illustration.
    If not, turn the crankshaft 1 complete revolution (360°) and align the timing marks as above.


29. REMOVE NO. 1 CHAIN TENSIONER ASSEMBLY

NOTICE:
  1. Never rotate the crankshaft with the chain tensioner removed.
  2. When rotating the camshaft with the timing chain removed, rotate the crankshaft counterclockwise 40° from the TDC first.

  1. A158627E01
    While turning the stopper plate of the tensioner clockwise, push in the plunger of the chain tensioner as shown in the illustration.

  1. While turning the stopper plate of the tensioner counterclockwise, insert a bar of φ3.5 mm (0.138 in.) into the holes on the stopper plate and tensioner to fix the stopper plate in place.

  1. Remove the 2 bolts and chain tensioner.


30. REMOVE CHAIN TENSIONER SLIPPER
  1. Remove the chain tensioner slipper.


31. REMOVE NO. 1 IDLE GEAR SHAFT

  1. A072959E01
    Using a 10 mm hexagon wrench, remove the No. 2 idle gear shaft, No. 1 idle gear and No. 1 idle gear shaft.


32. REMOVE NO. 2 CHAIN VIBRATION DAMPER

  1. G036844E01
    Remove the 2 No. 2 chain vibration dampers.


33. REMOVE NO. 1 CHAIN SUB-ASSEMBLY
  1. Remove the No. 1 chain.


34. REMOVE NO. 1 CHAIN VIBRATION DAMPER

  1. A076292E01
    Remove the 2 bolts and No. 1 chain vibration damper.


35. REMOVE CAMSHAFT TIMING GEARS AND NO. 2 CHAIN

  1. G038067E01
    While raising the No. 2 chain tensioner, insert a pin of φ1.0 mm (0.0394 in.) into the hole to fix the tensioner in place.

  1. G038110E01
    Hold the hexagonal portion of the camshaft with a wrench, and remove the 2 bolts, camshaft timing gear, camshaft timing sprocket and No. 2 chain.

    NOTICE:
    1. Be careful not to damage the cylinder head and valve lifter with the wrench.
    2. Do not disassemble the camshaft timing gear.


36. REMOVE NO. 2 CHAIN TENSIONER ASSEMBLY

  1. A072962E01
    Remove the bolt and No. 2 chain tensioner.


37. REMOVE NO. 1 CAMSHAFT AND NO. 2 CAMSHAFT

NOTICE:
As the thrust clearance of the camshaft is small, the camshaft must be kept level while it is being removed. If the camshaft is not kept level, the portion of the cylinder head which receives the shaft thrust may crack or be damaged, causing the camshaft to seize or break. To avoid this, the following steps should be carried out.

  1. A072966E03
    Rotate the camshafts counterclockwise using a wrench so that the cam lobes of the No. 1 cylinder face each direction as shown in the illustration.

  1. A072967E17
    Uniformly loosen and remove the 16 bearing cap bolts in the sequence shown in the illustration.

  1. Remove the 8 bearing caps and 2 camshafts.


38. REMOVE CYLINDER HEAD SUB-ASSEMBLY RH

  1. A076273E03
    Using a 10 mm bi-hexagon wrench, uniformly loosen the 8 cylinder head bolts in the sequence shown in the illustration. Remove the 8 cylinder head bolts and plate washers.

    NOTICE:
    1. Be careful not to drop the plate washers into the cylinder head.
    2. Cylinder head warpage or cracking could result from removing bolts in the incorrect order.

  1. A076805E01
    Lift the cylinder head from the dowels on the cylinder block, and place the cylinder head on wooden blocks on a bench.

    NOTICE:
    Be careful not to damage the contact surfaces of the cylinder head and cylinder block.

    HINT:
    If the cylinder head is difficult to lift off, pry between the cylinder head and cylinder block with a screwdriver.


39. REMOVE NO. 1 CAMSHAFT BEARING

A158703

40. REMOVE NO. 2 CAMSHAFT BEARING

A158539

41. REMOVE CYLINDER HEAD GASKET

42. REMOVE NO. 3 CHAIN TENSIONER ASSEMBLY

  1. A072965E01
    Remove the bolt and No. 3 chain tensioner.


43. REMOVE NO. 3 CAMSHAFT AND NO. 4 CAMSHAFT

NOTICE:
As the thrust clearance of the camshaft is small, the camshaft must be kept level while it is being removed. If the camshaft is not kept level, the portion of the cylinder head which receives the shaft thrust may crack or be damaged, causing the camshaft to seize or break. To avoid this, the following steps should be carried out.

  1. A072968E17
    Uniformly loosen and remove the 16 bearing cap bolts in the sequence shown in the illustration.

  1. Remove the 8 bearing caps and 2 camshafts.


44. REMOVE CYLINDER HEAD SUB-ASSEMBLY LH

  1. A072969E11
    Uniformly loosen and remove the 2 cylinder head bolts in the sequence shown in the illustration.

  1. A076277E02
    Using a 10 mm bi-hexagon wrench, uniformly loosen the 8 cylinder head bolts in the sequence shown in the illustration. Remove the 8 cylinder head bolts and plate washers.

    NOTICE:
    1. Be careful not to drop the plate washers into the cylinder head.
    2. Cylinder head warpage or cracking could result from removing bolts in the incorrect order.

  1. A076804E01
    Lift the cylinder head from the dowels on the cylinder block, and place the cylinder head on wooden blocks on a bench.

    NOTICE:
    Be careful not to damage the contact surfaces of the cylinder head and cylinder block.

    HINT:
    If the cylinder head is difficult to lift off, pry between the cylinder head and cylinder block with a screwdriver.


45. REMOVE NO. 2 CYLINDER HEAD GASKET
← COMPONENTS (from Jan 2012)REMOVAL (from Jan 2012) →