2011-2013 Land Cruiser · Service Manual Engine / Hybrid / EV System

REMOVAL

Removal / installation · Vehicles built from Jan 2012

Versions by build date: Sep 2011 – Dec 2011 from Jan 2012


1. REMOVE TIMING CHAIN COVER SUB-ASSEMBLY
(Click here)

2. SET NO. 1 CYLINDER TO TDC/COMPRESSION
  1. Temporarily install the pulley set bolt.

  1. A222172E01
    Turn the crankshaft clockwise to align the timing mark on the crank angle sensor plate with the RH block bore center line (TDC/compression).
    Text in Illustration 
    *1
    Center Line
    *2
    Timing Mark
    *3
    Sensor Plate

  1. A225378E01
    Check that the timing marks of the camshaft timing gears are aligned with the timing marks of the bearing caps as shown in the illustration.
    If not, turn the crankshaft clockwise 1 revolution (360°) and align the timing marks as above.
    Text in Illustration 
    *1
    Timing Mark


3. REMOVE NO. 1 CHAIN TENSIONER ASSEMBLY

  1. A124589E05
    Move the stopper plate upward to release the lock, and push the plunger deep into the tensioner.
    Text in Illustration 
    *1
    Plunger
    *2
    Stopper Plate
    *3
    Pin

  1. Move the stopper plate downward to set the lock, and insert a pin with a diameter of 1.27 mm (0.0500 in.) into the stopper plate hole.

  1. A095165E02
    Remove the 2 bolts and No. 1 chain tensioner assembly.


4. REMOVE CHAIN TENSIONER SLIPPER

  1. A223730
    Remove the chain tensioner slipper.


5. REMOVE CHAIN SUB-ASSEMBLY

  1. A221173E01
    Turn the crankshaft counterclockwise 10° to loosen the chain of the crankshaft timing sprocket.
    Text in Illustration 
    *1
    Center Line
    *2
    Timing Mark
    *3
    Sensor Plate

  1. Remove the pulley set bolt.

  1. A221174
    Remove the chain sub-assembly from the crankshaft timing sprocket and place it on the crankshaft.

  1. A095682E12
    Turn the camshaft timing gear assembly on bank 1 clockwise approximately 60° so that it is as shown in the illustration. Be sure to loosen the chain sub-assembly between the banks.

  1. Remove the chain sub-assembly.

    Text in Illustration 
    *A
    for Bank 1


6. REMOVE NO. 1 IDLE GEAR SHAFT

  1. A221175
    Using a 10 mm hexagon wrench, remove the No. 2 idle gear shaft, No. 1 idle gear and No. 1 idle gear shaft.


7. REMOVE NO. 1 CHAIN VIBRATION DAMPER

  1. A223642
    Remove the 2 bolts and No. 1 chain vibration damper.


8. REMOVE NO. 2 CHAIN VIBRATION DAMPER

  1. A221176
    Remove the 2 No. 2 chain vibration dampers.


9. REMOVE CRANKSHAFT TIMING SPROCKET

  1. A158530E01
    Remove the crankshaft timing sprocket.


10. REMOVE CAMSHAFT TIMING GEARS AND NO. 2 CHAIN (for Bank 1)

  1. A221132E01
    While raising the No. 2 chain tensioner assembly, insert a pin with a diameter of 1.0 mm (0.0394 in.) into the hole to hold the No. 2 chain tensioner assembly.
    Text in Illustration 
    *1
    Pin
    *2
    Plunger
    *a
    Push

  1. A221177E01
    Using SST to hold the hexagonal portion of each camshaft, loosen the bolts of the camshaft timing gear assembly and camshaft timing exhaust gear assembly.
    SST
    09922-10010  
    Text in Illustration 
    *a
    Turn
    *b
    Hold

    NOTICE:
    Do not loosen the other 4 bolts. If any of the 4 bolts is loosened, replace the camshaft timing gear assembly and/or camshaft timing exhaust gear assembly with a new one.

  1. Remove the 2 bolts and camshaft timing gear assembly together with the No. 2 chain.


11. REMOVE NO. 2 CHAIN TENSIONER ASSEMBLY

  1. A221178
    Remove the bolt and No. 2 chain tensioner assembly.


12. REMOVE CAMSHAFT BEARING CAP (for Bank 1)

  1. A129700E06
    Check that the camshafts are positioned as shown in the illustration.
    Text in Illustration 
    *1
    Knock Pin
    *a
    Front View

  1. A221179E01
    Uniformly loosen and remove the 8 bearing cap bolts in several steps in the sequence shown in the illustration.

  1. A221180E01
    Uniformly loosen and remove the 12 bearing cap bolts in several steps in the sequence shown in the illustration.

    NOTICE:
    Uniformly loosen the bolts while keeping the camshaft level.

  1. Remove the 5 camshaft bearing caps.

  1. Remove the camshaft and No. 2 camshaft.


13. REMOVE CAMSHAFT HOUSING SUB-ASSEMBLY RH

  1. A221181E01
    Remove the camshaft housing sub-assembly RH by prying between the cylinder head and camshaft housing sub-assembly RH with a screwdriver.
    Text in Illustration 
    *1
    Protective Tape

    NOTICE:
    Be careful not to damage the contact surfaces of the cylinder head and camshaft housing sub-assembly RH.

    HINT:
    Tape the screwdriver tip before use.


14. REMOVE CAMSHAFT TIMING GEARS AND NO. 2 CHAIN (for Bank 2)

  1. A221182E01
    While pushing down the No. 3 chain tensioner assembly, insert a pin with a diameter of 1.0 mm (0.0394 in.) into the hole to hold the No. 3 chain tensioner assembly.
    Text in Illustration 
    *1
    Pin
    *2
    Plunger
    *a
    Push

  1. A223637E01
    Using SST to hold the hexagonal portion of each camshaft, loosen the bolts of the camshaft timing gear assembly and camshaft timing exhaust gear assembly.
    SST
    09922-10010  
    Text in Illustration 
    *a
    Turn
    *b
    Hold

    NOTICE:
    Do not loosen the other 4 bolts. If any of the 4 bolts is loosened, replace the camshaft timing gear assembly and/or camshaft timing exhaust gear assembly with a new one.

  1. Remove the 2 bolts and camshaft timing gear together with the No. 2 chain.


15. REMOVE NO. 3 CHAIN TENSIONER ASSEMBLY

  1. A221183
    Remove the bolt and No. 3 chain tensioner assembly.


16. REMOVE CAMSHAFT BEARING CAP (for Bank 2)

  1. A223636E01
    Check that the camshafts are positioned as shown in the illustration.
    Text in Illustration 
    *1
    Knock Pin
    *a
    Front View

  1. A221184E01
    Uniformly loosen and remove the 8 bearing cap bolts in several steps in the sequence shown in the illustration.

  1. A221185E01
    Uniformly loosen and remove the 13 bearing cap bolts in several steps in the sequence shown in the illustration.

    NOTICE:
    Uniformly loosen the bolts while keeping the camshaft level.

  1. Remove the 5 camshaft bearing caps.

  1. Remove the No. 3 camshaft and No. 4 camshaft.


17. REMOVE CAMSHAFT HOUSING SUB-ASSEMBLY LH

  1. A221186E01
    Remove the camshaft housing sub-assembly LH by prying between the cylinder head and camshaft housing sub-assembly LH with a screwdriver.
    Text in Illustration 
    *1
    Protective Tape

    NOTICE:
    Be careful not to damage the contact surfaces of the cylinder head and camshaft housing sub-assembly LH.

    HINT:
    Tape the screwdriver tip before use.


18. REMOVE NO. 1 VALVE ROCKER ARM SUB-ASSEMBLY
  1. Remove the 24 valve rocker arms from the cylinder head.

    HINT:
    Arrange the removed parts in the correct order.


19. REMOVE VALVE LASH ADJUSTER ASSEMBLY
  1. Remove the 24 valve lash adjusters from the cylinder head.

    HINT:
    Arrange the removed parts in the correct order.


20. REMOVE VALVE STEM CAP
  1. Remove the 24 valve stem caps from the cylinder head.

    HINT:
    Arrange the removed parts in the correct order.


21. REMOVE REAR WATER BY-PASS JOINT

  1. A076534E01
    Remove the 2 bolts, 4 nuts, rear water by-pass joint and 2 gaskets.

  1. Remove the O-ring from the No. 1 water outlet pipe.


22. REMOVE CYLINDER HEAD SUB-ASSEMBLY

  1. A221092E01
    Using a 10 mm bi-hexagon wrench, uniformly loosen the 8 cylinder head bolts in the sequence shown in the illustration. Remove the 8 cylinder head bolts and plate washers.

    NOTICE:
    1. Be careful not to drop washers into the cylinder head sub-assembly.
    2. Cylinder head warpage or cracking could result from removing bolts in an incorrect order.

    HINT:
    Arrange the removed parts in the correct order.

  1. Remove the cylinder head sub-assembly.


23. REMOVE CYLINDER HEAD LH

  1. A221093E01
    Uniformly loosen and remove the 2 bolts in several steps in the sequence shown in the illustration.

  1. A221094E01
    Using a 10 mm bi-hexagon wrench, uniformly loosen the 8 bolts in the sequence shown in the illustration. Remove the 8 cylinder head bolts and plate washers.

    NOTICE:
    1. Be careful not to drop washers into the cylinder head sub-assembly.
    2. Cylinder head warpage or cracking could result from removing bolts in an incorrect order.

    HINT:
    Be sure to keep the removed parts for each installation position separate.

  1. Remove the cylinder head LH.


24. REMOVE CYLINDER HEAD GASKET

25. REMOVE NO. 2 CYLINDER HEAD GASKET
← REMOVAL (Sep 2011 – Dec 2011)INSTALLATION (Sep 2011 – Dec 2011) →