2011-2013 Land Cruiser · Service Manual Vehicle Interior

Back Door Entry Unlock Function does not Operate

Circuit diagnosis · Vehicles built Sep 2011 – Dec 2011

Versions by build date: Sep 2011 – Dec 2011 from Jan 2012

DESCRIPTION

When the back door opener switch is turned on, the certification ECU (smart key ECU assembly) uses the back door electrical key antenna (for outer) and antenna to output a request signal to the outside of the vehicle for a distance of approximately 1.0 m (3.28 ft.) from the back door. A key near the back door detects this request and transmits its ID code. The door control receiver receives the ID code and sends this ID code to the certification ECU (smart key ECU assembly). The certification ECU (smart key ECU assembly) checks if the ID code is valid. When the ID code is valid, the certification ECU (smart key ECU assembly) sends a back door open signal to the main body ECU using the CAN communication line and stops outputting request signals. The main body ECU then unlocks the back door.

WIRING DIAGRAM

B187333E01

INSPECTION PROCEDURE


1. CHECK POWER DOOR LOCK OPERATION
  1. When the door control switch of the master switch assembly is operated, check that the locked doors unlock.

    OK:
    Door locks operate normally.



NG
GO TO POWER DOOR LOCK CONTROL SYSTEM (Click here)
OK


2. READ VALUE USING INTELLIGENT TESTER (DOOR LOCK POSITION SWITCH)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the engine switch on (IG).

  1. Turn the intelligent tester on.

  1. Enter the following menus: Body / Main Body / Data List.

  1. Read the Data List according to the display on the intelligent tester.

    Main Body 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Back Lock Pos switch
    Back door lock position switch signal / ON or OFF
    ON: Back door is unlocked
    OFF: Back door is locked
    -

    OK:
    On the intelligent tester screen, the display changes between ON and OFF as shown in the chart above.



NG
GO TO POWER DOOR LOCK CONTROL SYSTEM (Proceed to Only Back Door LOCK/UNLOCK Functions do not Operate) (Click here)
OK


3. READ VALUE USING INTELLIGENT TESTER (BACK DOOR HANDLE SW)
  1. Using the intelligent tester, read the Data List.

    Main Body 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Back Door Handle SW
    Back door opener switch / ON or OFF
    ON: Back door opener switch is pushed
    OFF: Back door opener switch is not pushed
    -

    OK:
    "ON" (switch is pushed) or "OFF" (switch is not pushed) appears on the screen.



NG
Go to step 4
OK

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

4. CHECK BACK DOOR OPENER SWITCH

  1. B185531E03
    Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    1 (UL) - 2 (L)
    3 (B) - 2 (L)
    Not pushed
    10 kΩ or higher
    1 (UL) - 2 (L)
    Lock switch pushed
    Below 1 Ω
    3 (B) - 2 (L)
    Open switch pushed
    Below 1 Ω



NG
REPLACE BACK DOOR OPENER SWITCH (Click here)
OK


5. CHECK HARNESS AND CONNECTOR (MAIN BODY ECU - BACK DOOR OPENER SWITCH)
B154889E01
  1. Disconnect the E1 ECU connector.

  1. Disconnect the S7 switch connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    E1-26 (BDSU) - S7-3 (B)
    Always
    Below 1 Ω
    E1-26 (BDSU) or S7-3 (B) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)


← Entry Interior Alarm does not Sound (from Jan 2012)Back Door Entry Unlock Function does not Operate (from Jan 2012) →