2011-2013 Land Cruiser · Service Manual Engine / Hybrid / EV System

INSPECTION

Inspection · Vehicles built Sep 2011 – Dec 2011

NOTICE:
The following tests must be done within 3 to 5 seconds to prevent the coil from burning out.


INSPECT STARTER ASSEMBLY

  1. G036244E03
    Perform pull-in test.

    1. Remove the nut, then disconnect the lead wire from terminal C.

    2. Connect the battery to the starter as shown in the illustration. Check that the clutch pinion gear moves outward.
      If the clutch pinion gear does not move, replace the magnet starter switch assembly.

  1. G036245E03
    Perform holding test.

    1. When the battery is connected as above with the clutch pinion gear out, disconnect the negative (-) lead from terminal C. Check that the pinion gear remains out.
      If the clutch pinion gear returns inward, replace the magnet starter switch assembly.

  1. G036246E03
    Inspect clutch pinion gear return.

    1. Disconnect the negative (-) lead from the starter body. Check that the clutch pinion gear returns inward.
      If the clutch pinion gear does not return inward, replace the magnet starter switch assembly.

  1. A075961E03
    Perform the operation test without load.

    1. Connect the lead wire to terminal C with the nut.

      Torque:
      5.9 N*m{ 60 kgf*cm , 52 in.*lbf }

    2. Grip the starter in a vise.

    3. Connect the battery and an ammeter to the starter as shown.

    4. Check that the starter rotates smoothly and steadily with the clutch pinion gear extended.

    5. Check that the ammeter reads the specified current.

      Standard current:
      100 A or less at 11.5 V

      If the result is not as specified, replace the starter assembly.


INSPECT STARTER ARMATURE ASSEMBLY

  1. P010584E02
    Inspect the commutator for an open circuit.

    1. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      Commutator
      Always
      Below 1 Ω

      If the result is not as specified, replace the starter armature assembly.

  1. P010585E02
    Inspect the commutator for a short circuit.

    1. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      Commutator - Armature
      Always
      10 kΩ or higher

      If the result is not as specified, replace the starter armature assembly.

  1. Check the commutator surface for dirt and burns.
    If the surface is dirty or burnt, correct it with sandpaper (#400) or a lathe.

  1. P010586E01
    Inspect the commutator circle runout.

    1. Place the commutator on V-blocks.

    2. Using a dial indicator, measure the circle runout.

      Maximum circle runout:
      0.05 mm (0.00197 in.)

      If the runout is more than the maximum, correct it with sandpaper (#400) or replace the starter armature assembly.

  1. P010587E01
    Using a vernier caliper, measure the commutator diameter.

    Standard diameter:
    35.0 mm (1.38 in.)

    Minimum diameter:
    34.0 mm (1.34 in.)

    If the diameter is less than the minimum, replace the starter armature assembly.

  1. A115027
    Measure the undercut depth of the commutator.

    Standard undercut depth:
    0.7 mm (0.0276 in.)

    Minimum undercut depth:
    0.2 mm (0.00787 in.)

    If the undercut depth is less than the minimum, increase the depth using a hacksaw blade.

  1. Inspect the bearings.

    1. Check that the bearing rotates smoothly.


INSPECT BRUSH

  1. A062430E06
    Using a vernier caliper, measure the brush length.

    Standard brush length:
    15.0 mm (0.591 in.)

    Minimum brush length:
    9.0 mm (0.354 in.)

    If the length is less than the minimum, replace the starter brush holder assembly and starter yoke assembly.


INSPECT STARTER BRUSH HOLDER ASSEMBLY

  1. A177673
    Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    Positive brush holder - Negative brush holder
    Always
    10 kΩ or higher

    If the result is not as specified, replace the starter brush holder assembly.

  1. A115032
    Inspect the load of the brush spring.

    1. Take the pull scale reading immediately after the brush spring separates from the brush.

      Standard spring installed load:
      21.5 to 27.5 N (2.2 to 2.8 kgf, 4.8 to 6.2 lbf)

      Minimum spring installed load:
      12.7 N (1.3 kgf, 2.9 lbf)

      If the spring load is less than the minimum, replace the starter brush holder assembly.


INSPECT STARTER YOKE ASSEMBLY

  1. P010588E03
    Inspect for an open circuit.

    1. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      Terminal C wire - Brush
      Always
      Below 1 Ω

      If the result is not as specified, replace the starter yoke assembly.

    2. A076125E02
      Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester connection
      Condition
      Specified Condition
      Shunt coil terminal (A) - Shunt coil terminal (B)
      20°C (68°F)
      1.5 to 1.9 Ω

      If the result is not as specified, replace the starter yoke assembly.


INSPECT STARTER CLUTCH SUB-ASSEMBLY

  1. A115056E01
    Check that the starter clutch cannot be rotated counterclockwise, and can be rotated clockwise.
    If the starter clutch is not as specified, replace the starter clutch sub-assembly.


INSPECT MAGNET STARTER SWITCH ASSEMBLY

  1. A076119E03
    Inspect the pull-in coil.

    1. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      Terminals 50 - Terminal C
      Always
      Below 1 Ω

      If the result is not as specified, replace the magnet starter switch assembly.

  1. A076120E03
    Inspect the holding coil.

    1. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      Terminal 50 - Switch body
      Always
      Below 2 Ω

      If the result is not as specified, replace the magnet starter switch assembly.

← DISASSEMBLY (Sep 2011 – Dec 2011)REASSEMBLY (Sep 2011 – Dec 2011) →