2011-2013 Land Cruiser · Service Manual Vehicle Exterior

REMOVAL

Removal / installation · Vehicles built from Jan 2012

HINT:
  1. Use the same procedure for the RH and LH sides.
  2. The procedure listed below is for the LH side.


1. REMOVE OUTER REAR VIEW MIRROR LH
(Click here)

2. REMOVE OUTER MIRROR LH

B180587
  1. Push the upper part of the mirror surface and tilt it.

  1. Using a moulding remover, detach the 4 claws and separate the outer mirror LH from the mirror body.

    HINT:
    Apply protective tape to the outer rear mirror LH to prevent it from being damaged.

  1. B189668
    w/ EC Mirror:
    Disconnect the connector and remove the outer mirror LH.

  1. B189669
    w/ Mirror Heater:
    Disconnect the 2 connectors and remove the outer mirror LH.


3. REMOVE OUTER MIRROR COVER LH

B241698E02

HINT:
Be sure to detach the claws of the outer mirror cover in the order shown in the illustration.

  1. B245779E01
    Using 2 screwdrivers, detach the 2 claws.

    HINT:
    Tape the screwdriver tip before use.

    Text in Illustration 
    *1
    Protective Tape

  1. Insert a screwdriver into the slot as shown in the illustration and push on the outer mirror body to create a space between the outer mirror body and outer mirror cover.

    NOTICE:
    Be careful not to break the ribs.

    HINT:
    Tape the screwdriver tip before use.


    B245757E01
    Text in Illustration  
    *1
    Protective Tape
    *2
    Rib
    *a
    Inner Side of Outer Mirror Cover
    -
    -

  1. B302378E01
    Apply protective tape to the areas of the body cover and outer mirror cover as shown in the illustration.

    HINT:
    Tape the moulding remover before use.

    Text in Illustration  
    *1
    Protective Tape

  1. Insert a moulding remover into the space made between the outer mirror body and outer mirror cover.

    NOTICE:
    Do not insert the moulding remover more than 4 mm (0.157 in.).

    Standard:
    Area
    Specified Condition
    a
    4mm

  1. B302379E01
    Slide the moulding remover downwards as shown in the illustration to detach the 2 claws.

    NOTICE:
    1. Do not insert the moulding remover more than 4 mm (0.157 in.).
    2. Do not slide the moulding remover past the point approximately 40 mm (1.57 in.) from the bottom edge of the outer mirror cover as the outer mirror body will become damaged.

    Text in Illustration  
    *1
    Protective Tape

    Standard:
    Area
    Specified Condition
    a
    40mm
    b
    4mm

  1. Remove the moulding remover B.

  1. B245762E02
    Apply protective tape to the areas of the body cover and outer mirror cover as shown in the illustration.
    Text in Illustration  
    *1
    Protective Tape
    *a
    Lower Side

  1. Insert a moulding remover B between the outer mirror cover and outer mirror body as shown in the illustration and detach the claw.

  1. B245633E01
    Using a screwdriver, detach the claw.
    Text in Illustration  
    *1
    Protective Tape

  1. B245761
    Detach the 2 claws and remove the outer mirror cover.

    NOTICE:
    When removing the cover, be careful not to damage the side turn signal light assembly or cover.


4. REMOVE SIDE TURN SIGNAL LIGHT ASSEMBLY LH

  1. E199248
    Remove the 3 screws and light.

  1. Disconnect the connector.

← COMPONENTS (from Jan 2012)INSPECTION (from Jan 2012) →