Microphone Circuit between Microphone and Radio Receiver
Circuit diagnosis · Vehicles built from Jan 2012
Versions by build date: Sep 2011 – Dec 2011 from Jan 2012
DESCRIPTION
This circuit sends the microphone signal from the map light assembly (telephone microphone assembly) to the radio receiver assembly.It also supplies power source from the radio receiver assembly to the map light assembly (telephone microphone assembly).
WIRING DIAGRAM


INSPECTION PROCEDURE
| 1. INSPECT RADIO RECEIVER ASSEMBLY |
Disconnect the F54 radio receiver assembly connector.

Measure the voltage according to the value(s) in the table below.
- Standard Voltage:
Tester Connection
Switch Condition
Specified Condition
F54-3 (MACC) - Body ground
Engine switch on (IG)
4 to 6 V
- Standard Resistance:
Tester Connection
Condition
Specified Condition
F54-6 (SGND) - Body ground
Always
Below 1 Ω
F54-5 (MIN-) - Body ground
Always
Below 1 Ω
Text in Illustration *1
Component without harness connected
(Radio Receiver Assembly)
|
|
||||
| OK | |
| 2. CHECK HARNESS AND CONNECTOR (MAP LIGHT ASSEMBLY - RADIO RECEIVER ASSEMBLY) |
Disconnect the R7 map light assembly and F54 radio receiver assembly connectors.
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Condition
Specified Condition
R7-20 (SNS2) - F54-1 (SNS2)
Always
Below 1 Ω
R7-27 (MI1+) - F54-2 (MIN+)
Always
Below 1 Ω
R7-26 (MIC-) - F54-5 (MIN-)
Always
Below 1 Ω
R7-25 (ACC) - F54-3 (MACC)
Always
Below 1 Ω
R7-20 (SNS2) - Body ground
Always
10 kΩ or higher
R7-27 (MI1+) - Body ground
Always
10 kΩ or higher
R7-26 (MIC-) - Body ground
Always
10 kΩ or higher
R7-25 (ACC) - Body ground
Always
10 kΩ or higher
F54-6 (SGND) - Body ground
Always
10 kΩ or higher
|
|
||||
| OK | |
| 3. INSPECT MAP LIGHT ASSEMBLY |
Measure the resistance according to the value(s) in the table below.

- Standard Resistance:
Tester Connection
Condition
Specified Condition
R7-20 (SNS2) - R7-26 (MIC-)
Always
Below 1 Ω
Text in Illustration *1
Component without harness connected
(Map Light Assembly)
|
|
||||
| OK | |
| 4. INSPECT MAP LIGHT ASSEMBLY |
Reconnect the radio receiver assembly connector.

Reconnect the map light assembly connector.
Turn the engine switch on (ACC).
Connect an oscilloscope to terminals R7-27 (MI1+) and R7-26 (MIC-) of the map light assembly connector.
Check the waveform of the telephone microphone assembly using an oscilloscope.
Result Result
Proceed to
A waveform synchronized with the voice input to the telephone microphone assembly is output
A
A waveform synchronized with the voice input to the telephone microphone assembly is not output
B
| *1 |
Component with harness connected (Map Light Assembly) |
|
|
||||
| A | ||
| ||
| 5. REPLACE TELEPHONE MICROPHONE ASSEMBLY |
Replace the telephone microphone assembly (Click here).
Check if the same malfunction recurs.
Result Result
Proceed to
Malfunction does not recur
(returns to normal)
A
Malfunction recurs
B
|
|
||||
| A | ||
| ||
