2011-2013 Land Cruiser · Service Manual Audio / Visual / Telematics

Microphone Circuit between Microphone and Radio Receiver

Circuit diagnosis · Vehicles built Sep 2011 – Dec 2011

Versions by build date: Sep 2011 – Dec 2011 from Jan 2012

DESCRIPTION

This circuit sends the microphone signal from the map light assembly (telephone microphone assembly) to the radio receiver assembly.
It also supplies power source from the radio receiver assembly to the map light assembly (telephone microphone assembly).

WIRING DIAGRAM

E177629E09

INSPECTION PROCEDURE


1. INSPECT RADIO RECEIVER ASSEMBLY

  1. E163028E18
    Disconnect the F54 radio receiver assembly connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    F54-3 (MACC) - Body ground
    Engine switch on (IG)
    4 to 6 V

    Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    F54-6 (SGND) - Body ground
    Always
    Below 1 Ω
    F54-5 (MIN-) - Body ground
    Always
    Below 1 Ω

    Text in Illustration 
    *1
    Component without harness connected
    (Radio Receiver Assembly)



NG
REPLACE RADIO RECEIVER ASSEMBLY (Click here)
OK


2. CHECK HARNESS AND CONNECTOR (MAP LIGHT ASSEMBLY - RADIO RECEIVER ASSEMBLY)
  1. Disconnect the R7 map light assembly and F54 radio receiver assembly connectors.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    R7-20 (SNS2) - F54-1 (SNS2)
    Always
    Below 1 Ω
    R7-27 (MI1+) - F54-2 (MIN+)
    Always
    Below 1 Ω
    R7-26 (MIC-) - F54-5 (MIN-)
    Always
    Below 1 Ω
    R7-25 (ACC) - F54-3 (MACC)
    Always
    Below 1 Ω
    R7-20 (SNS2) - Body ground
    Always
    10 kΩ or higher
    R7-27 (MI1+) - Body ground
    Always
    10 kΩ or higher
    R7-26 (MIC-) - Body ground
    Always
    10 kΩ or higher
    R7-25 (ACC) - Body ground
    Always
    10 kΩ or higher
    F54-6 (SGND) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


3. INSPECT MAP LIGHT ASSEMBLY

  1. E187245E09
    Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    R7-20 (SNS2) - R7-26 (MIC-)
    Always
    Below 1 Ω

    Text in Illustration 
    *1
    Component without harness connected
    (Map Light Assembly)



NG
Go to step 5
OK


4. INSPECT MAP LIGHT ASSEMBLY

  1. E187250E07
    Reconnect the radio receiver assembly connector.

  1. Reconnect the map light assembly connector.

  1. Turn the engine switch on (ACC).

  1. Connect an oscilloscope to terminals R7-27 (MI1+) and R7-26 (MIC-) of the map light assembly connector.

  1. Check the waveform of the telephone microphone assembly using an oscilloscope.

    Result 
    Result
    Proceed to
    A waveform synchronized with the voice input to the telephone microphone assembly is output
    A
    A waveform synchronized with the voice input to the telephone microphone assembly is not output
    B

Text in Illustration 
*1
Component with harness connected
(Map Light Assembly)


B
Go to step 5
A

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE (Click here)

5. REPLACE TELEPHONE MICROPHONE ASSEMBLY
  1. Replace the telephone microphone assembly (Click here).

  1. Check if the same malfunction recurs.

    Result 
    Result
    Proceed to
    Malfunction does not recur
    (returns to normal)
    A
    Malfunction recurs
    B



B
REPLACE MAP LIGHT ASSEMBLY (Click here)
A

END


← Cellular Phone Voice Circuit between Radio Receiver and Stereo Component Amplifier (from Jan 2012)Microphone Circuit between Microphone and Radio Receiver (from Jan 2012) →