2011-2013 Land Cruiser · Service Manual Engine / Hybrid / EV System

INSTALLATION

Removal / installation · Vehicles built Sep 2011 – Dec 2011


1. INSTALL AIR FUEL RATIO SENSOR (for Bank 1 Sensor 1)

  1. A158663
    Temporarily install the sensor to the exhaust pipe by hand.

  1. A168888E01
    Using SST, tighten the sensor.
    SST
    09224-00010  

    Torque:
    without SST:
    44 N*m{ 449 kgf*cm , 32 ft.*lbf }
    with SST:
    40 N*m{ 408 kgf*cm , 30 ft.*lbf }

    HINT:
    1. Use a torque wrench with a fulcrum length of 30 cm (11.8 in.). If using a torque wrench with a length that is not 30 cm (11.8 in.), calculate the torque specification for the torque wrench and SST based on the "without SST" torque specification (Click here).
    2. Make sure SST and the wrench are connected in a straight line.


2. INSTALL AIR FUEL RATIO SENSOR (for Bank 2 Sensor 1)

  1. A158663
    Temporarily install the sensor to the exhaust pipe by hand.

  1. A168888E01
    Using SST, tighten the sensor.
    SST
    09224-00010  

    Torque:
    without SST:
    44 N*m{ 449 kgf*cm , 32 ft.*lbf }
    with SST:
    40 N*m{ 408 kgf*cm , 30 ft.*lbf }

    HINT:
    1. Use a torque wrench with a fulcrum length of 30 cm (11.8 in.). If using a torque wrench with a length that is not 30 cm (11.8 in.), calculate the torque specification for the torque wrench and SST based on the "without SST" torque specification (Click here).
    2. Make sure SST and the wrench are connected in a straight line.


3. INSTALL NO. 2 HEATED OXYGEN SENSOR (for Bank 1 Sensor 2)

  1. A158663
    Temporarily install the sensor to the exhaust pipe by hand.

  1. A148589E01
    Using SST, tighten the sensor.
    SST
    09224-00010  

    Torque:
    without SST:
    44 N*m{ 449 kgf*cm , 32 ft.*lbf }
    with SST:
    40 N*m{ 408 kgf*cm , 30 ft.*lbf }

    HINT:
    1. Use a torque wrench with a fulcrum length of 30 cm (11.8 in.). If using a torque wrench with a length that is not 30 cm (11.8 in.), calculate the torque specification for the torque wrench and SST based on the "without SST" torque specification (Click here).
    2. Make sure SST and the wrench are connected in a straight line.


4. INSTALL HEATED OXYGEN SENSOR (for Bank 2 Sensor 2)

  1. A158663
    Temporarily install the sensor to the exhaust pipe by hand.

  1. A148589E01
    Using SST, tighten the sensor.
    SST
    09224-00010  

    Torque:
    without SST:
    44 N*m{ 449 kgf*cm , 32 ft.*lbf }
    with SST:
    40 N*m{ 408 kgf*cm , 30 ft.*lbf }

    HINT:
    1. Use a torque wrench with a fulcrum length of 30 cm (11.8 in.). If using a torque wrench with a length that is not 30 cm (11.8 in.), calculate the torque specification for the torque wrench and SST based on the "without SST" torque specification (Click here).
    2. Make sure SST and the wrench are connected in a straight line.


5. INSTALL FRONT EXHAUST PIPE ASSEMBLY
  1. Install a new gasket and the front exhaust pipe to the exhaust manifold with 3 new nuts.

    Torque:
    54 N*m{ 554 kgf*cm , 40 ft.*lbf }

  1. Connect the air fuel ratio sensor connector.

  1. Connect the heated oxygen sensor connector.

  1. Attach the heated oxygen sensor wire clamp.


6. INSTALL FRONT NO. 2 EXHAUST PIPE ASSEMBLY
  1. Install a new gasket and the front No. 2 exhaust pipe to the exhaust manifold LH with 3 new nuts.

    Torque:
    54 N*m{ 554 kgf*cm , 40 ft.*lbf }

  1. Connect the air fuel ratio sensor connector.

  1. Connect the heated oxygen sensor connector.


7. INSTALL CENTER EXHAUST PIPE ASSEMBLY
  1. Install the center exhaust pipe to the 3 exhaust pipe supports.

  1. Install 2 new gaskets to the front exhaust pipe and front No. 2 exhaust pipe.

  1. Install the 4 bolts.

    Torque:
    48 N*m{ 489 kgf*cm , 35 ft.*lbf }


8. INSTALL TAILPIPE ASSEMBLY
  1. Install the tailpipe to the 2 exhaust pipe supports.

  1. Install a new gasket to the center exhaust pipe.

  1. A167906E02
    Connect the tailpipe and center exhaust pipe with a new clamp.

    Torque:
    32 N*m{ 326 kgf*cm , 24 ft.*lbf }

    HINT:
    Install the clamp within the angle range shown in the illustration.


9. INSPECT FOR EXHAUST GAS LEAK
If gas is leaking, tighten the areas necessary to stop the leak. Replace damaged parts as necessary.

10. INSTALL NO. 2 ENGINE UNDER COVER

  1. A178462
    Install the No. 2 engine under cover with the 2 bolts.

    Torque:
    29 N*m{ 296 kgf*cm , 21 ft.*lbf }

← REMOVAL (Sep 2011 – Dec 2011)PRECAUTION (from Sep 2011) →