INSTALLATION
Removal / installation · Vehicles built from Sep 2011
| 1. INSTALL NO. 2 HEATED OXYGEN SENSOR (for Bank 1 Sensor 2) |
Temporarily install the sensor to the exhaust pipe by hand.

Using SST, tighten the sensor.

- SST
- 09224-00010
- Torque:
- without SST:
- 44 N*m{ 449 kgf*cm , 32 ft.*lbf }
- with SST:
- 40 N*m{ 408 kgf*cm , 30 ft.*lbf }
Text in Illustration *1
Fulcrum Length
- HINT:
- Use a torque wrench with a fulcrum length of 300 mm (11.8 in.). If using a torque wrench with a length that is not 300 mm (11.8 in.), calculate the torque specification for the torque wrench and SST based on the "without SST" torque specification (Click here).
- Make sure SST and the wrench are connected in a straight line.
- Use a torque wrench with a fulcrum length of 300 mm (11.8 in.). If using a torque wrench with a length that is not 300 mm (11.8 in.), calculate the torque specification for the torque wrench and SST based on the "without SST" torque specification (Click here).
| 2. INSTALL HEATED OXYGEN SENSOR (for Bank 2 Sensor 2) |
Temporarily install the sensor to the exhaust pipe by hand.
Using SST, tighten the sensor.

- SST
- 09224-00010
- Torque:
- without SST:
- 44 N*m{ 449 kgf*cm , 32 ft.*lbf }
- with SST:
- 40 N*m{ 408 kgf*cm , 30 ft.*lbf }
Text in Illustration *1
Fulcrum Length
- HINT:
- Use a torque wrench with a fulcrum length of 300 mm (11.8 in.). If using a torque wrench with a length that is not 300 mm (11.8 in.), calculate the torque specification for the torque wrench and SST based on the "without SST" torque specification (Click here).
- Make sure SST and the wrench are connected in a straight line.
- Use a torque wrench with a fulcrum length of 300 mm (11.8 in.). If using a torque wrench with a length that is not 300 mm (11.8 in.), calculate the torque specification for the torque wrench and SST based on the "without SST" torque specification (Click here).
| 3. INSTALL FRONT EXHAUST PIPE ASSEMBLY |
Install a new gasket and the front exhaust pipe to the exhaust manifold RH with 2 new nuts.
- Torque:
- 54 N*m{ 551 kgf*cm , 40 ft.*lbf }
Install the wire harness clamp bracket of the oxygen sensor to the transmission with the bolt.
- Torque:
- 29 N*m{ 296 kgf*cm , 21 ft.*lbf }
Connect the heated oxygen sensor connector.
| 4. INSTALL FRONT NO. 2 EXHAUST PIPE ASSEMBLY |
Install a new gasket and the front No. 2 exhaust pipe to the exhaust manifold LH with 2 new nuts.
- Torque:
- 54 N*m{ 551 kgf*cm , 40 ft.*lbf }
Install the wire harness clamp bracket of the oxygen sensor to the transmission with the bolt.
- Torque:
- 29 N*m{ 296 kgf*cm , 21 ft.*lbf }
Connect the heated oxygen sensor connector.
| 5. INSTALL CENTER EXHAUST PIPE ASSEMBLY |
Install 2 new gaskets to the front exhaust pipe and front No. 2 exhaust pipe.
Install the center exhaust pipe to the 3 exhaust pipe supports, and then install the 4 bolts.
- Torque:
- 48 N*m{ 489 kgf*cm , 35 ft.*lbf }
| 6. INSTALL EXHAUST PIPE DAMPER |
Install the exhaust pipe damper to the tailpipe with the 2 bolts.
- Torque:
- 19 N*m{ 194 kgf*cm , 14 ft.*lbf }
| 7. INSTALL TAILPIPE ASSEMBLY |
Install the tailpipe to the 2 exhaust pipe supports.
Install a new gasket to the center exhaust pipe.
Connect the tailpipe to the center exhaust pipe.
Attach a new clamp to the tailpipe and center exhaust pipe. Then install the bolt to the clamp.

- Torque:
- 32 N*m{ 326 kgf*cm , 24 ft.*lbf }
Text in Illustration *1
Gasket
*a
Top
*b
LH Side
*c
Front
- HINT:
- Install the clamp within the angle range shown in the illustration.
| 8. INSPECT FOR EXHAUST GAS LEAK |
| 9. INSTALL NO. 2 ENGINE UNDER COVER |
Install the No. 2 engine under cover with the 2 bolts.
- Torque:
- 29 N*m{ 296 kgf*cm , 21 ft.*lbf }
