2011-2013 Land Cruiser · Service Manual Drivetrain

DISASSEMBLY

Removal / installation · Vehicles built from Sep 2011


1. REMOVE PROPELLER SHAFT HEAT INSULATOR BRACKET SUB-ASSEMBLY

  1. C174577
    Remove the bolt and bracket.


2. REMOVE TRANSFER OIL PUMP PLATE

  1. C159613
    Remove the 4 bolts, oil pump plate and oil pump driven rotor.

    NOTICE:
    Do not drop the oil pump driven rotor.

  1. Remove the O-ring from the oil pump plate.

  1. C173490
    Remove the transfer oil seal ring from the input shaft.

  1. C173598E01
    Remove the oil pump drive rotor from the input shaft.


3. REMOVE TRANSFER CASE STRAIGHT PIN

  1. C162213E01
    Remove the 2 straight pins.

    NOTICE:
    Do not drop the straight pins.


4. REMOVE TRANSFER CASE PLUG

  1. C177450
    Using a 10 mm hexagon wrench, remove the case plug, compression spring, ball and relief valve seat.


5. REMOVE TRANSFER OIL PUMP PLATE OIL SEAL

  1. C173329
    Using a screwdriver, pry out the oil seal from the oil pump plate.

    NOTICE:
    Be careful not to damage the oil seal and oil pump plate contact surfaces.

    HINT:
    Tape the screwdriver tip before use.


6. REMOVE FRONT OUTPUT SHAFT COMPANION FLANGE SUB-ASSEMBLY

  1. C173330E01
    Using SST and a hammer, release the staked part of the nut.
    SST
    09930-00010   (09931-00010, 09931-00020)

    NOTICE:
    1. Be sure to use SST with the tapered surface facing the shaft.
    2. Do not grind the tip of SST with a grinder, etc.
    3. Completely loosen the staked part of the nut when removing it.
    4. Do not damage the threads of the transfer driven sprocket.

  1. C173331E01
    Using SST to hold the companion flange, remove the lock nut.
    SST
    09330-00021  

  1. C173332E01
    Using SST, remove the companion flange.
    SST
    09950-40011   (09951-04020, 09952-04010, 09953-04030, 09954-04010, 09955-04051, 09957-04010, 09958-04011)

  1. Remove the O-ring from the companion flange.


7. REMOVE TRANSFER CASE FRONT OIL SEAL

  1. C172371E01
    Using SST, tap out the oil seal.
    SST
    09308-00010  

    NOTICE:
    Be careful not to damage the oil seal and front transfer case contact surface.


8. REMOVE REAR OUTPUT SHAFT COMPANION FLANGE SUB-ASSEMBLY

  1. C173333E01
    Using SST and a hammer, release the staked part of the nut.
    SST
    09930-00010   (09931-00010, 09931-00020)

    NOTICE:
    1. Be sure to use SST with the tapered surface facing the shaft.
    2. Do not grind the tip of SST with a grinder, etc.
    3. Completely loosen the staked part of the nut when removing it.
    4. Do not damage the threads of the rear transfer output shaft.

  1. C173334E01
    Using SST to hold the companion flange, remove the lock nut.
    SST
    09330-00021  

  1. C173335E01
    Using SST, remove the companion flange.
    SST
    09950-40011   (09951-04020, 09952-04010, 09953-04030, 09954-04010, 09955-04051, 09957-04010, 09958-04011)

  1. Remove the O-ring from the companion flange.


9. REMOVE TRANSFER CASE REAR OIL SEAL

  1. C172373E01
    Using SST, tap out the oil seal.
    SST
    09308-00010  

    NOTICE:
    Be careful not to damage the oil seal and rear transfer case contact surface.


10. REMOVE NO. 1 TRANSFER CASE PLUG

  1. C176791
    Remove the plug, compression spring and pin.


11. REMOVE TRANSFER CASE PLUG

  1. C173336
    Using a 6 mm hexagon wrench, remove the plug.


12. REMOVE REAR TRANSFER CASE ASSEMBLY

  1. C173337
    Remove the 14 bolts.

  1. Remove the rear transfer case.

    HINT:
    If necessary, tap the rear transfer case with a plastic-faced hammer to remove it.


13. REMOVE FRONT TRANSFER OUTPUT SHAFT NEEDLE ROLLER BEARING

C173595E01
  1. Remove the needle roller bearing and spacer from the output shaft.


14. REMOVE NO. 2 TRANSFER GEAR SHIFT FORK

  1. C173338
    Using 2 screwdrivers and a hammer, tap out the 4 shift fork shaft snap rings.

  1. C173339
    Remove the bolt. Then remove the No. 2 gear shift fork together with the high and low clutch sleeve from the shift actuator.


15. REMOVE TRANSFER SHIFT ACTUATOR ASSEMBLY

  1. C173373
    Remove the No. 1 gear shift fork bolt.

  1. C173374
    Remove the 3 bolts.

  1. C241090E01
    Remove the shift actuator and No. 1 gear shift fork from the rear transfer case.

    NOTICE:
    Take care not to drop the No. 1 gear shift fork.

  1. C160356E02
    Remove the O-ring from the shift actuator.


16. REMOVE REAR TRANSFER OUTPUT SHAFT ASSEMBLY

  1. C173484
    Using a snap ring expander, expand the snap ring as shown in the illustration.

  1. C175777
    Using a plastic-faced hammer, carefully tap the rear transfer case, and remove the output shaft together with the drive chain and driven sprocket.

  1. Remove the output shaft and driven sprocket from the drive chain.

    NOTICE:
    Do not drop the output shaft washers.

  1. C174066
    Using a snap ring expander, remove the snap ring from the rear transfer case.


17. REMOVE FRONT DRIVE CLUTCH SLEEVE

C174057
  1. Remove the clutch sleeve from the output shaft.


18. REMOVE SIDE GEAR SHAFT HOLDER BEARING

  1. C160519
    Using a screwdriver, remove the snap ring.

  1. C173485E01
    Using SST, remove the bearing.
    SST
    09308-00010  


19. REMOVE TRANSFER OIL SEPARATOR SUB-ASSEMBLY

  1. C173486
    Remove the 3 bolts and oil separator.

  1. Remove the O-ring from the oil separator.


20. REMOVE TRANSFER CASE MAGNET

C174062
  1. Remove the magnet from the oil separator.


21. REMOVE TRANSFER INPUT SHAFT ASSEMBLY

  1. C159719
    Using a 14 mm hexagon wrench, remove the 2 case plugs from the front transfer case.

  1. C176062
    Using a snap ring expander, expand the snap ring as shown in the illustration. Then remove the input shaft from the front transfer case.


22. REMOVE TRANSFER LOW PLANETARY RING GEAR

  1. C173488
    Using a screwdriver, remove the snap ring. Then remove the low planetary ring gear from the front transfer case.

  1. C174065
    Using a snap ring expander, remove the snap ring from the front transfer case.


23. REMOVE TRANSFER DRIVEN SPROCKET BEARING

  1. C173489
    Using a screwdriver, remove the snap ring. Then remove the bearing from the front transfer case.


24. REMOVE NO. 1 SYNCHRONIZER RING (for Manual Transmission)

C174150
  1. Remove the synchronizer ring from the input shaft.


25. REMOVE NO. 1 TRANSFER INPUT SHAFT SEAL RING

  1. C173492E01
    Remove the seal ring from the input shaft.


26. REMOVE TRANSFER INPUT SHAFT BEARING

  1. C173491
    Using a snap ring expander, remove the snap ring.

  1. C173493E01
    Using SST and a press, press out the bearing.
    SST
    09555-55010  
    09950-60010   (09951-00490)
    09950-70010   (09951-07100)

    NOTICE:
    Be careful not to drop or damage the input shaft, low planetary gear and low planetary gear bearings.

    HINT:
    When the bearing is removed, the input shaft, low planetary gear, and 2 low planetary gear bearings will come off.


27. REMOVE TRANSFER INPUT SHAFT BIMETAL FORMED BUSH

  1. C173631E01
    Using SST, remove the bush.
    SST
    09387-00041   (09387-01021, 09387-01030, 09387-01040)


28. REMOVE TRANSFER INPUT SHAFT PLUG

  1. C173494E01
    Using SST and a hammer, tap out the input shaft plug.
    SST
    09950-70010   (09951-07150)
    09950-60010   (09951-00300)


29. REMOVE TRANSFER OUTPUT SHAFT WASHER

  1. C173600
    Remove the 2 output shaft washers from the output shaft.


30. REMOVE NO. 1 TRANSFER OUTPUT SHAFT SPACER

  1. C173602
    Using 2 screwdrivers and a hammer, tap out the snap ring.

  1. C173603
    Remove the output shaft spacer from the output shaft.

  1. C173604
    Remove the seal ring from the output shaft spacer.

  1. C173605E01
    Remove the straight pin from the output shaft.


31. REMOVE CENTER DIFFERENTIAL CASE

  1. C173606
    Remove the center differential case from the output shaft.

  1. C173607
    for Manual Transmission:
    Using a snap ring expander, remove the snap ring.

  1. C173608
    for Manual Transmission:
    Remove the synchromesh shifting key spring and No. 2 synchromesh shifting keys from the center differential case.

  1. C173609E01
    Using SST, remove the needle roller bearing.
    SST
    09308-00010  

  1. C173630E01
    Using SST, remove the needle roller bearing.
    SST
    09387-00041   (09387-01021, 09387-01030, 09387-01040)


32. REMOVE TRANSFER OUTPUT SHAFT SPACER

  1. C173610
    Using 2 screwdrivers and a hammer, tap out the snap ring.

  1. C173611
    Remove the output shaft spacer from the output shaft.

  1. C173612E01
    Remove the straight pin from the output shaft.


33. REMOVE TRANSFER DRIVE SPROCKET SUB-ASSEMBLY

  1. C173613
    Remove the drive sprocket from the output shaft.


34. REMOVE TRANSFER DRIVE SPROCKET BEARING

  1. C173614
    Remove the bearing from the output shaft.


35. REMOVE REAR TRANSFER OUTPUT SHAFT

  1. C173616E01
    Using SST and a press, press out the bearing.
    SST
    09527-10011  

    NOTICE:
    Be careful not to drop or damage the output shaft.

  1. C173615
    Remove the needle roller bearing from the output shaft.

← REMOVAL (from Jan 2012)INSPECTION (from Sep 2011) →