2011-2013 Land Cruiser · Service Manual General

SERVICE DATA

Specifications · Vehicles built Sep 2011 – Dec 2011

Versions by build date: Sep 2011 – Dec 2011 from Jan 2012


Camshaft timing oil control valve:
Tester Connection
Condition
Specified Condition
1 - 2
20°C (68°F)
6.9 to 7.9 Ω


Crankshaft position sensor:
Tester Connection
Condition
Specified Condition
1 - 2
Cold
1630 to 2740 Ω
Hot
2065 to 3225 Ω


Engine coolant temperature sensor:
Tester Connection
Condition
Specified Condition
1 - 2
Approx. 20°C (68°F)
2.32 to 2.59 kΩ
Approx. 80°C (176°F)
0.310 to 0.326 kΩ


Throttle body:
Tester Connection
Condition
Specified Condition
2 (M+) - 1 (M-)
20°C (68°F)
0.3 to 100 Ω


Knock sensor:
Tester Connection
Condition
Specified Condition
1 - 2
20°C (68°F)
120 to 280 kΩ


Ignition relay No. 2:
Tester Connection
Condition
Specified Condition
IG2 MAIN fuse
Always
Below 1 Ω
1C-1 - 1B-8
Battery voltage is not applied to terminals 1B-6 and 1B-7
10 kΩ or higher
Battery voltage is applied to terminals 1B- 6 and 1B-7
Below 1 Ω


EFI relay:
Tester Connection
Condition
Specified Condition
EFI No. 1 fuse
Always
Below 1 Ω
1C-1 - 1B-4
Battery voltage is not applied to terminals 1B-2 and 1B-3)
10 kΩ or higher
Battery voltage is applied to terminals 1B- 2 and 1B-3)
Below 1 Ω


Circuit opening relay:
Tester Connection
Condition
Specified Condition
3 - 5
Battery voltage is not applied to terminals 1 and 2
10 kΩ or higher
Battery voltage is applied to terminals 1 and 2
Below 1 Ω


EFI No. 2 relay:
Tester Connection
Condition
Specified Condition
3 - 5
Battery voltage is not applied to terminals 1 and 2
10 kΩ or higher
Battery voltage is applied to terminals 1 and 2
Below 1 Ω


Accelerator pedal:
Tester display
Condition
Specified Condition
Accel Sens. No. 1 Volt %
Released
10 to 22%
Depressed
54 to 86%
Accel Sens. No. 2 Volt %
Released
12 to 42%
Depressed
66 to 98%


Main body ECU (IG1 No.1):
Tester Connection
Condition
Specified Condition
2A-1 - 2B-17
Battery voltage is not applied to terminals 2B-5 and 2D-43
10 kΩ or higher
Battery voltage is applied to terminals 2B-5 and 2D-43
Below 1 Ω


Air fuel ration sensor (for Bank 1 sensor 1):
Tester Connection
Condition
Specified Condition
1 (HT1A) - 2 (+B)
20°C (68°F)
1.8 to 3.4 Ω


Air fuel ration sensor (for Bank 2 sensor 1):
Tester Connection
Condition
Specified Condition
1 (HT2A) - 2 (+B)
20°C (68°F)
1.8 to 3.4 Ω


Heated oxygen sensor (for Bank 1 sensor 2):
Tester Connection
Condition
Specified Condition
1 (HT1B) - 2 (+B)
20°C (68°F)
11 to 16 Ω


Heated oxygen sensor (for Bank 2 sensor 2):
Tester Connection
Condition
Specified Condition
1 (HT2B) - 2 (+B)
20°C (68°F)
11 to 16 Ω


A/F sensor heater relay:
Tester Connection
Condition
Specified Condition
A/F fuse
Always
Below 1 Ω
1C-1 - 1A-4
Battery voltage is not applied to terminals 1A-2 and 1A-3
10 kΩ or higher
Battery voltage is applied to terminals 1A- 2 and 1A-3
Below 1 Ω


Spark plug:
Recommended spark plug
Correct electrode gap for new spark plug
Maximum electrode gap for used spark plug
Standard insulation resistance
DENSO made: K20HR-U11
Correct electrode gap for new spark plug 1.0 to 1.1 mm (0.0394 to 0.0433in.)
1.3 mm (0.0512 in.)
10 MΩ or higher
NGK made: LFR6C11

← HOW TO DETERMINE NUT STRENGTH (from Sep 2011)SERVICE DATA (from Jan 2012) →