2011-2013 Land Cruiser · Service Manual General

SERVICE DATA

Specifications · Vehicles built Sep 2011 – Dec 2011

Versions by build date: Sep 2011 – Dec 2011 from Jan 2012


MAF meter:
Tester Connection
Condition
Specified Condition
4 (THA) - 5(E2)
-20°C (-4°F)
12.5 to 16.9 kΩ
20°C (68°F)
2.19 to 2.67 kΩ
60°C (140°F)
0.50 to 0.68 kΩ


Camshaft position sensor:
Tester Connection
Condition
Specified Condition
1 - 2
Hot
835 to 1400Ω
Cold
1060 to 1645Ω


Crankshaft position sensor:
Tester Connection
Condition
Specified Condition
1 - 2
Hot
1630 to 2740Ω
Cold
2065 to 3225Ω


Engine coolant temperature sensor:
Tester Connection
Condition
Specified Condition
1 - 2
Approximately. 20°C (68°F)
2.32 to 2.59 kΩ
Approximately. 80°C (176°F)
0.310 to 0.326 kΩ


Intake air temperature sensor:
Tester Connection
Condition
Specified Condition
1 - 2
Approximately. 20°C (68°F)
2.21 to 2.65 kΩ
Approximately. 60°C (140°F)
0.55 to 0.61 kΩ


Integration relay (IG2):
Tester Connection
Condition
Specified Condition
IG2 MAIN fuse
Always
Below 1 Ω
1C-1 - 1B-8
Battery voltage is not applied to terminals 1B-6 and 1B-7
10 kΩ or higher
Battery voltage is applied to terminals 1B- 6 and 1B-7
Below 1 Ω


Integration relay (EFI MAIN):
Tester Connection
Condition
Specified Condition
EFI No. 1 fuse
Always
Below 1 Ω
1C-1 - 1B-4
Battery voltage is not applied to terminals 1B-2 and 1B-3)
10 kΩ or higher
Battery voltage is applied to terminals 1B- 2 and 1B-3)
Below 1 Ω


Integration relay (EFI MAIN 2):
Tester Connection
Condition
Specified Condition
EFI No. 1 fuse
Always
Below 1 Ω
1C-1 - 1A-4
Battery voltage is not applied to terminals 1A-2 and 1A-3
10 kΩ or higher
Battery voltage is applied to terminals 1A-2 and 1A-3
Below 1 Ω


Fuel pump relay (SUB PUMP):
Tester Connection
Condition
Specified Condition
3 - 5
Battery voltage is not applied to terminals 1 and 2
10 kΩ or higher
Battery voltage is applied to terminals 1 and 2
Below 1 Ω


EDU relay (EDU1, EDU2):
Tester Connection
Condition
Specified Condition
3 - 5
Battery voltage is not applied to terminals 1 and 2
10 kΩ or higher
Battery voltage is applied to terminals 1 and 2
Below 1 Ω


Main body ECU (IG1 No.1):
Tester Connection
Condition
Specified Condition
2A-1 - 2B-17
Battery voltage is not applied to terminals 2B-5 and 2D-43
10 kΩ or higher
Battery voltage is applied to terminals 2B-5 and 2D-43
Below 1 Ω


No.1 vacuum switching valve:
Tester Connection
Condition
Specified Condition
1-2
20 °C
37 to 44 Ω
1 - Body ground
2 - Body ground
Always
10 kΩ or higher


Diesel turbo pressure sensor:
Tester Connection
Switch Condition
Specified Condition
C80-3 (VC) - C80-1 (E2)
Engine switch on (IG)
4.5 to 5.5V


Accelerator pedal:
Tester Display
Condition
Specified Condition
Accel Sens. No.1 Volt %
Released
10 to 22%
Depressed
52 to 90%
Accel Sens. No.2 Volt %
Released
24 to 40%
Depressed
68 to 99%

← TORQUE SPECIFICATIONS (Sep 2011 – Dec 2011)SERVICE DATA (from Jan 2012) →