SERVICE DATA
Specifications · Vehicles built from Jan 2012
Versions by build date: Sep 2011 – Dec 2011 from Jan 2012
MASS AIR FLOW METER (w/o DPF)
Tester Connection
|
Condition
|
Specified Condition
|
4 (THA) - 5(E2)
|
-20°C (-4°F)
|
12.5 to 16.9 kΩ
|
20°C (68°F)
|
2.19 to 2.67 kΩ
|
60°C (140°F)
|
0.50 to 0.68 kΩ
|
CAMSHAFT POSITION SENSOR
Tester Connection
|
Condition
|
Specified Condition
|
1 - 2
|
Hot
|
835 to 1400Ω
|
Cold
|
1060 to 1645Ω
|
CRANKSHAFT POSITION SENSOR
Tester Connection
|
Condition
|
Specified Condition
|
1 - 2
|
Hot
|
1630 to 2740Ω
|
Cold
|
2065 to 3225Ω
|
ENGINE COOLANT TEMPERATURE SENSOR
Tester Connection
|
Condition
|
Specified Condition
|
1 - 2
|
Approximately. 20°C (68°F)
|
2.32 to 2.59 kΩ
|
Approximately. 80°C (176°F)
|
0.310 to 0.326 kΩ
|
AIR FUEL RATIO SENSOR
Tester Connection
|
Condition
|
Specified Condition
|
1 - 2
|
20°C (68°F)
|
1.8 to 3.4 Ω
|
INTAKE AIR TEMPERATURE SENSOR
Tester Connection
|
Condition
|
Specified Condition
|
1 - 2
|
Approximately. 20°C (68°F)
|
2.21 to 2.65 kΩ
|
Approximately. 60°C (140°F)
|
0.55 to 0.61 kΩ
|
Integration relay (IG2)
Tester Connection
|
Condition
|
Specified Condition
|
IG2 MAIN fuse
|
Always
|
Below 1 Ω
|
1C-1 - 1B-8
|
Battery voltage is not applied to terminals 1B-6 and 1B-7
|
10 kΩ or higher
|
Battery voltage is applied to terminals 1B- 6 and 1B-7
|
Below 1 Ω
|
Integration relay (EFI MAIN)
Tester Connection
|
Condition
|
Specified Condition
|
EFI No. 1 fuse
|
Always
|
Below 1 Ω
|
1C-1 - 1B-4
|
Battery voltage is not applied to terminals 1B-2 and 1B-3)
|
10 kΩ or higher
|
Battery voltage is applied to terminals 1B- 2 and 1B-3)
|
Below 1 Ω
|
Integration relay (EFI MAIN 2)
Tester Connection
|
Condition
|
Specified Condition
|
EFI No. 1 fuse
|
Always
|
Below 1 Ω
|
1C-1 - 1A-4
|
Battery voltage is not applied to terminals 1A-2 and 1A-3
|
10 kΩ or higher
|
Battery voltage is applied to terminals 1A-2 and 1A-3
|
Below 1 Ω
|
FUEL PUMP RELAY (SUB PUMP)
Tester Connection
|
Condition
|
Specified Condition
|
3 - 5
|
Battery voltage is not applied to terminals 1 and 2
|
10 kΩ or higher
|
Battery voltage is applied to terminals 1 and 2
|
Below 1 Ω
|
EDU relay (EDU1)
Tester Connection
|
Condition
|
Specified Condition
|
3 - 5
|
Battery voltage is not applied to terminals 1 and 2
|
10 kΩ or higher
|
Battery voltage is applied to terminals 1 and 2
|
Below 1 Ω
|
EDU relay (EDU2)
Tester Connection
|
Condition
|
Specified Condition
|
3 - 5
|
Battery voltage is not applied to terminals 1 and 2
|
10 kΩ or higher
|
Battery voltage is applied to terminals 1 and 2
|
Below 1 Ω
|
AIR FUEL RATIO SENSOR RELAY (A/F)
Tester Connection
|
Condition
|
Specified Condition
|
3 - 5
|
Battery voltage is not applied to terminals 1 and 2
|
10 kΩ or higher
|
Battery voltage is applied to terminals 1 and 2
|
Below 1 Ω
|
MAIN BODY ECU (IG1 No.1)
Tester Connection
|
Condition
|
Specified Condition
|
2A-1 - 2B-17
|
Battery voltage is not applied to terminals 2B-5 and 2D-43
|
10 kΩ or higher
|
Battery voltage is applied to terminals 2B-5 and 2D-43
|
Below 1 Ω
|
No.1 VACUUM SWITCHING VALVE
Tester Connection
|
Condition
|
Specified Condition
|
1-2
|
20 °C
|
37 to 44 Ω
|
1 - Body ground 2 - Body ground
|
Always
|
10 kΩ or higher
|
DIESEL TURBO PRESSURE SENSOR
Tester Connection
|
Switch Condition
|
Specified Condition
|
C80-3 (VC) - C80-1 (E2)
|
Engine switch on (IG)
|
4.5 to 5.5V
|
ACCELERATOR PEDAL
Tester Display
|
Condition
|
Specified Condition
|
Accel Sens. No.1 Volt %
|
Released
|
10 to 22%
|
Depressed
|
52 to 90%
|
Accel Sens. No.2 Volt %
|
Released
|
24 to 40%
|
Depressed
|
68 to 99%
|