2011-2013 Land Cruiser · Service Manual Engine / Hybrid / EV System

DATA LIST / ACTIVE TEST

System information · Vehicles built Sep 2011 – Dec 2011

Versions by build date: Sep 2011 – Dec 2011 from Jan 2012


READ DATA LIST

HINT:
Using the intelligent tester to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.

NOTICE:
In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.

  1. Connect the intelligent tester to the DLC3.

  2. Turn the ignition switch to ON.

  3. Turn the intelligent tester on.

  4. Enter the following menus: Powertrain / Cruise Control / Data List.

  5. According to the display on the intelligent tester, read the "Data List".

    Cruise Control 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    CCS Vehicle Spd
    Vehicle speed / min.: 0 km/h (0 mph), max.: 255 km/h (159 mph)
    Actual vehicle speed displayed
    -
    CCS Mem Vehicle Spd
    Vehicle speed / min.: 0 km/h (0 mph), max.: 200 km/h (125 mph)
    Actual vehicle speed stored in memory
    -
    Cruise Operation Status
    Transmission range sensor signal / ON or OFF
    ON: Shift lever in D
    OFF: Shift lever not in D
    for A/T
    Clutch switch signal / ON or OFF
    ON: Clutch pedal released
    OFF: Clutch pedal depressed
    for M/T
    Cruise Control
    Cruise control / ON or OFF
    ON: Cruise control operating
    OFF: Cruise control not operating
    -
    CCS Indicator M-CPU
    CRUISE main indicator light (Main CPU) / ON or OFF
    ON: CRUISE main indicator light on
    OFF: CRUISE main indicator light off
    -
    CCS Ready M-CPU
    Cruise control system standby condition (Main CPU) / ON or OFF
    ON ←→ OFF: Changes each time main switch pushed
    -
    CCS Main SW M-CPU
    Cruise control main switch (Main CPU) / ON or OFF
    ON: Cruise control main switch (Main CPU) on
    OFF: Cruise control main switch (Main CPU) off
    -
    CCS Main SW S-CPU
    Cruise control main switch (Sub CPU) / ON or OFF
    ON: Cruise control main switch (Sub CPU) on
    OFF: Cruise control main switch (Sub CPU) off
    -
    Cancel Switch
    CANCEL switch / ON or OFF
    ON: CANCEL switch on
    OFF: CANCEL switch off
    -
    SET/COAST Switch
    -SET switch / ON or OFF
    ON: -SET switch on
    OFF: -SET switch off
    -
    RES/ACC Switch
    +RES switch / ON or OFF
    ON: +RES switch on
    OFF: +RES switch off
    -
    Stop Light SW M-CPU
    Stop light switch signal (Main CPU) / ON or OFF
    ON: Brake pedal depressed
    OFF: Brake pedal released
    -
    Throttle Opening Angle
    Cruise throttle opening angle / min.: 0 deg, max.: 125 deg
    Actual demanded throttle angle
    for 2UZ-FE, 1GR-FE
    Fuel injection quantity / min.: 0%, max.: 100%
    Actual demanded fuel injection quantity
    for 1VD-FTV
    # Codes
    Number of trouble codes / Min.: 0, Max.: 255
    -
    -


PERFORM ACTIVE TEST

HINT:
Using the intelligent tester to perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.

  1. Connect the intelligent tester to the DLC3.

  2. Turn the ignition switch to ON.

  3. Turn the intelligent tester on.

  4. Enter the following menus: Body / Combination Meter / Active Test.

  5. According to the display on the intelligent tester, perform the "Active Test".

    Combination Meter 
    Tester Display
    Test Part
    Control Range
    Diagnostic Note
    Indicat. Lamp Cruise
    CRUISE main indicator light operation
    OFF or ON
    -

← FAIL-SAFE CHART (from Jan 2012)DATA LIST / ACTIVE TEST (from Jan 2012) →