DATA LIST / ACTIVE TEST
System information · Vehicles built from Jan 2012
Versions by build date: Sep 2011 – Dec 2011 from Jan 2012
| READ DATA LIST |
- HINT:
- Using the intelligent tester to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.
- NOTICE:
- In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Turn the intelligent tester on.
Enter the following menus: Powertrain / Cruise Control / Data List.
According to the display on the intelligent tester, read the "Data List".
Cruise Control Tester Display
Measurement Item/Range
Normal Condition
Diagnostic Note
CCS Vehicle Spd
Vehicle speed / min.: 0 km/h (0 mph), max.: 255 km/h (159 mph)
Actual vehicle speed displayed
-
CCS Mem Vehicle Spd
Vehicle speed / min.: 0 km/h (0 mph), max.: 200 km/h (125 mph)
Actual vehicle speed stored in memory
-
Cruise Operation Status
Transmission range sensor signal / ON or OFF
ON: Shift lever in D
OFF: Shift lever not in D
for A/T
Clutch switch signal / ON or OFF
ON: Clutch pedal released
OFF: Clutch pedal depressed
for M/T
Cruise Control
Cruise control / ON or OFF
ON: Cruise control operating
OFF: Cruise control not operating
-
CCS Indicator M-CPU
CRUISE main indicator light (Main CPU) / ON or OFF
ON: CRUISE main indicator light on
OFF: CRUISE main indicator light off
-
CCS Ready M-CPU
Cruise control system standby condition (Main CPU) / ON or OFF
ON ←→ OFF: Changes each time main switch pushed
-
Main SW M-CPU
Cruise control main switch (Main CPU) / ON or OFF
ON: Cruise control main switch (Main CPU) on
OFF: Cruise control main switch (Main CPU) off
-
Stop Light SW M-CPU
Stop light switch signal (Main CPU) / ON or OFF
ON: Brake pedal depressed
OFF: Brake pedal released
-
Cancel Switch
CANCEL switch / ON or OFF
ON: CANCEL switch on
OFF: CANCEL switch off
-
SET/COAST Switch
-SET switch / ON or OFF
ON: -SET switch on
OFF: -SET switch off
-
RES/ACC Switch
+RES switch / ON or OFF
ON: +RES switch on
OFF: +RES switch off
-
Brake Cancel Switch
Stop light switch signal
ON: Brake pedal depressed
OFF: Brake pedal released
for 1GR-FE, 1VD-FTV (w/ DPF), 3UR-FE
Throttle Opening Angle
Cruise throttle opening angle / min.: 0 deg, max.: 125 deg
Actual demanded throttle angle
for 1GR-FE, 1UR-FE, 3UR-FE
Fuel injection quantity / min.: 0%, max.: 100%
Actual demanded fuel injection quantity
for 1VD-FTV
# Codes
Number of trouble codes / Min.: 0, Max.: 255
-
-
| PERFORM ACTIVE TEST |
- HINT:
- Using the intelligent tester to perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Turn the intelligent tester on.
Enter the following menus: Body / Combination Meter / Active Test.
According to the display on the intelligent tester, perform the "Active Test".
Combination Meter Tester Display
Test Part
Control Range
Diagnostic Note
Indicat. Lamp Cruise
Cruise control indicator light operation
ON / OFF
-
Indicat. SET
Cruise control SET indicator light operation
ON / OFF
-