2011-2013 Land Cruiser · Service Manual Vehicle Interior

TERMINALS OF ECU

System information · Vehicles built Sep 2011 – Dec 2011

Versions by build date: Sep 2011 – Dec 2011 from Jan 2012


CHECK AIR CONDITIONING AMPLIFIER (w/ Rear Heater)
E132519E08
  1. Disconnect the E36, E35 and z53 air conditioning amplifier assembly connectors.

  2. Measure the voltage and resistance according to the value(s) in the table below.

    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    E36-6 (+B1) - E36-1 (GND)
    R - W-B
    Battery power source
    Always
    11 to 14 V
    E36-7 (+B2) - E36-1 (GND)
    R - W-B
    Battery power source
    Always
    11 to 14 V
    z53-3 (B BUS) - z53-1 (BUS G)
    -
    Power supply for BUS IC (for front)
    Always
    11 to 14 V
    z53-10 (B BUS) - z53-8 (BUS G)
    -
    Power supply for BUS IC (for front)
    Always
    11 to 14 V
    E36-5 (IG+) - E36-1 (GND)
    G - W-B
    Ignition power supply
    Engine switch on (IG)
    11 to 14 V
    Engine switch off
    Below 1 V
    E36-14 (RBBU) - E36-12 (RBUG)
    L - BR
    Power supply for BUS IC (for rear)
    Always
    11 to 14 V
    E35-25 (TR3) - Body ground
    V - Body ground
    Ground
    Engine switch on (IG)
    Driver side duct sensor temperature: 25°C (77°F)
    5000 +/-150 Ω
    E35-26 (TR4) - Body ground
    W - Body ground
    Ground
    Engine switch on (IG)
    Passenger side duct sensor temperature: 25°C (77°F)
    5000 +/-150 Ω
    E35-16 (SG-2) - Body ground
    G - Body ground
    Ground for pressure sensor
    Always
    Below 1 Ω
    E35-29 (SG-5) - Body ground
    G - Body ground
    Ground for compressor signal
    Always
    Below 1 Ω
    E36-2 (E1) - Body ground
    W-B - Body ground
    Ground
    Always
    Below 1 Ω
    E36-1 (GND) - Body ground
    W-B - Body ground
    Ground
    Always
    Below 1 Ω
    E35-6 (E2) - Body ground
    W-B - Body ground
    Ground
    Always
    Below 1 Ω
    E35-32 (SG-1) - Body ground
    B - Body ground
    Ground for room temperature sensor (for front)
    Always
    Below 1 Ω
    z53-6 (SGA) - Body ground
    -
    Ground for evaporator temperature sensor
    Always
    Below 1 Ω
    z53-1 (BUS G) - Body ground
    -
    Ground for BUS IC (for front)
    Always
    Below 1 Ω
    z53-8 (BUS G) - Body ground
    -
    Ground for BUS IC (for front)
    Always
    Below 1 Ω
    E35-34 (SGND) - Body ground
    BR - Body ground
    Ground for duct sensor (for driver side)
    Always
    Below 1 Ω
    E35-12 (SG-9) - Body ground
    L - Body ground
    Ground for duct sensor (for passenger side)
    Always
    Below 1 Ω
    E35-2 (SG-6) - Body ground
    G - Body ground
    Ground for room temperature sensor signal (for Rear LH and Rear RH)
    Always
    Below 1 Ω
    E36-12 (RBUG) - Body ground
    BR - Body ground
    Ground for BUS IC (for rear)
    Always
    Below 1 Ω
    E35-1 (SG) - Body ground
    P - Body ground
    Ground for evaporator temperature sensor signal (for Rear)
    Always
    Below 1 Ω
    1. If the result is not as specified, there may be a malfunction on the wire harness side.

  3. Reconnect the E36, E35 and z53 air conditioning amplifier assembly connectors.

  4. Measure the voltage and waveform according to the value(s) in the table below.

    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    E36-25 (CFN+) - Body ground
    R - Body ground
    Condenser FAN operation signal
    Engine switch on (IG)
    11 to 14 V
    E36-33 (COOL) - Body ground
    W - Body ground
    Cool box operation signal
    Engine switch on (IG)
    Cool box switch: ON
    11 to 14 V
    E36-29 (AC1) - Body ground
    L - Body ground
    Compressor operation signal
    Engine switch on (IG)
    A/C switch: OFF
    11 to 14 V
    Engine switch on (IG)
    A/C switch: ON
    Below 1 V
    E36-22 (ACT) - Body ground
    G - Body ground
    Compressor operation signal
    Engine switch on (IG)
    A/C switch: OFF
    Below 1 V
    Engine switch on (IG)
    A/C switch: ON
    11 to 14 V
    E35-28 (LOCK) - E35-29 (SG-5)
    L - G
    Air compressor lock sensor signal
    Engine idling
    A/C switch: ON
    Blower switch LO
    Pulse generation
    (see waveform 1)
    E35-10 (TAM) - E35-16 (SG-2)
    V - G
    Ambient temperature sensor signal
    Engine switch on (IG)
    Ambient temperature:
    25°C (77°F)
    1.6 to 1.8 V
    Engine switch on (IG)
    Ambient temperature:
    50°C (122°F)
    0.5 to 0.7 V
    E35-27 (S5-1) - E35-16 (SG-2)
    LG - G
    Power supply for pressure sensor
    Engine switch on (IG)
    4.5 to 5.5 V
    E35-20 (PRE) - E35-16 (SG-2)
    R - G
    Air conditioning pressure sensor signal
    Refrigerant pressure:
    Normal
    1.0 to 4.8 V
    Refrigerant pressure:
    Abnormal (less than 0.392 MPa [4.0 kgf/cm2, 57 psi])
    Below 1 V
    Refrigerant pressure:
    Abnormal (less than 3.187 MPa [32.5 kgf/cm2, 463 psi])
    4.8 V or higher
    E36-18 (MGC) - E36-1 (GND)
    R - W-B
    A/C compressor magnetic clutch operation signal
    Engine idling
    Blower switch LO
    A/C switch: ON
    Below 1 V
    E36-3 (BLW) - E36-1 (GND)
    R - W-B
    Blower motor control signal
    Engine switch on (IG)
    Blower switch LO
    Pulse generation
    (see waveform 2)
    E35-9 (TR) - E35-32 (SG-1)
    W - B
    Room temperature sensor signal (for front)
    Engine switch on (IG)
    Front side interior temperature: 25°C (77°F)
    1.6 to 1.8 V
    Room temperature sensor signal (for front)
    Engine switch on (IG)
    Front side interior temperature: 50°C (122°F)
    0.5 to 0.7 V
    E35-7 (TSD) - Body ground
    LG - Body ground
    Driver side solar sensor signal
    Engine switch on (IG)
    Solar sensor subjected to electric light
    0.8 to 4.3 V
    E35-8 (TSP) - Body ground
    GR - Body ground
    Passenger side solar sensor signal
    Engine switch on (IG)
    Solar sensor subjected to electric light
    0.8 to 4.3 V
    z53-7 (TEA) - z53-6 (SGA)
    -
    Evaporator temperature sensor signal
    Engine switch on (IG)
    Evaporator temperature: 15°C (59°F)
    1.4 to 1.8 V
    z53-2 (BUS) - z53-1 (BUS G)
    -
    BUS IC control signal (for front)
    Engine switch on (IG)
    Pulse generation
    z53-9 (BUS) - z53-8 (BUS G)
    -
    BUS IC control signal (for front)
    Engine switch on (IG)
    Pulse generation
    E35-18 (TR) - E35-2 (SG-6)
    R - G
    Room temperature sensor signal (for Rear LH)
    Engine switch on (IG)
    Vehicle interior temperature: 25°C (77°F)
    1.6 to 1.8 V
    Engine switch on (IG)
    Vehicle interior temperature: 50°C (122°F)
    0.5 to 0.7 V
    E35-19 (TR7) - E35-2 (SG-6)
    R - G
    Room temperature sensor signal (for Rear RH)
    Engine switch on (IG)
    Vehicle interior temperature: 25°C (77°F)
    1.6 to 1.8 V
    Engine switch on (IG)
    Vehicle interior temperature: 50°C (122°F)
    0.5 to 0.7 V
    E36-13 (RBUS) - E36-12 (RBUG)
    R - BR
    BUS IC control signal (for rear)
    Engine switch on (IG)
    Pulse generation
    E35-17 (TEC) - E35-1 (SG)
    W - P
    Evaporator temperature sensor signal (for Rear)
    Engine switch on (IG)
    Evaporator temperature:
    15°C (59°F)
    1.4 to 1.8 V
    E36-31 (ALT) - Body ground
    R - Body ground
    Generator signal
    Engine idling
    Pulse generation
    E36-32 (SW1) - Body ground
    BR - Body ground
    Idle up operation signal
    Engine switch on (IG)
    Idle up switch OFF
    Below 1 V
    Engine switch on (IG)
    Idle up switch ON
    11 to 14 V
    E36-20 (LIN1) - E36-1 (GND)
    Y - W-B
    LIN communication signal
    (for Front A/C switch)
    Engine switch on (IG)
    Pulse generation
    E36-21 (RLIN) - E36-1 (GND)
    L - W-B
    LIN communication signal
    (for Rear A/C switch)
    Engine switch on (IG)
    Pulse generation
    E36-27 (PTC1) - Body ground
    R - Body ground
    PTC1 heater relay operation signal
    Engine idling
    Set temperature: MAX HOT
    Engine coolant temperature: Below 65°C (149°F)
    Ambient temperature: Below 10°C (50°F)
    Blower switch off → LO
    Below 1 V → 11 to 14 V
    E36-26 (PTC2) - Body ground
    R - Body ground
    PTC2 heater relay operation signal
    E36-35 (PTC3) - Body ground
    R - Body ground
    PTC3 heater relay operation signal
    E36-17 (BLWH) - E36-1 (GND)
    L - W-B
    Blower motor control signal (for rear)
    Engine switch on (IG)
    Blower switch LO
    Pulse generation
    (see waveform 3)
    E36-19 (RMGV) - E36-1 (GND)
    B - W-B
    Rear cooling unit expansion valve signal
    Engine switch on (IG)
    11 to 14 V
    1. If the result is not as specified, the air conditioning amplifier assembly may have a malfunction.

  5. E157042E01
    Using an oscilloscope, check waveform 1.
    A/C Compressor Lock Sensor Signal 
    Item
    Content
    Terminal No. (Symbol)
    E35-28 (LOCK) - E35-29 (SG-5)
    Tool Setting
    200 mV/DIV., 10 ms/DIV.
    Condition
    Engine running
    Blower switch LO
    A/C switch on

    HINT:
    When the rear blower level is increased, the duty ratio changes accordingly.

  6. E103396E12
    Using an oscilloscope, check waveform 2.
    Blower Motor Control Signal 
    Item
    Content
    Terminal No. (Symbol)
    E36-3 (BLW) - E36-1 (GND)
    Tool Setting
    1 V/DIV., 500 μs/DIV.
    Condition
    Engine switch on (IG)
    Blower switch LO

    HINT:
    When the blower level is increased, the duty ratio changes accordingly.

  7. E103396E12
    Using an oscilloscope, check waveform 3.
    Rear Blower Motor Control Signal 
    Item
    Content
    Terminal No. (Symbol)
    E36-17 (BLWH) - E36-1 (GND)
    Tool Setting
    1 V/DIV., 500 μs/DIV.
    Condition
    Engine switch on (IG)
    Blower switch LO

    HINT:
    When the rear blower level is increased, the duty ratio changes accordingly.


CHECK AIR CONDITIONING AMPLIFIER ASSEMBLY (w/o Rear Heater)
B160781E04
  1. Disconnect the E81 and z54 air conditioning amplifier assembly connectors.

  2. Measure the resistance and voltage according to the value(s) in the table below.

    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    E81-21 (+B1) - E81-14 (GND)
    R - W-B
    Battery power source
    Always
    11 to 14 V
    z54-4 (B BUS) - z54-2 (BUS G)
    -
    Power supply for BUS IC (for front)
    Always
    11 to 14 V
    E81-1 (IG+) - E81-14 (GND)
    G - W-B
    Ignition power supply
    Engine switch on (IG)
    11 to 14 V
    Engine switch off
    Below 1 V
    E81-35 (SG-5) - Body ground
    G - Body ground
    Ground for compressor signal
    Always
    Below 1 Ω
    E81-13 (SG-2) - Body ground
    G - Body ground
    Ground for pressure sensor
    Always
    Below 1 Ω
    E81-14 (GND) - Body ground
    W-B - Body ground
    Ground
    Always
    Below 1 Ω
    E81-34 (SG-1) - Body ground
    B - Body ground
    Ground for room temperature sensor (for front)
    Always
    Below 1 Ω
    z54-5 (SGA) - Body ground
    -
    Ground for evaporator temperature sensor
    Always
    Below 1 Ω
    z54-2 (BUS G) - Body ground
    -
    Ground for BUS IC (for front)
    Always
    Below 1 Ω
    1. If the result is not as specified, there may be a malfunction on the wire harness side.

  3. Reconnect the E81 and z54 air conditioning amplifier assembly connectors.

  4. Measure the voltage and waveform according to the value(s) in the table below.

    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    E81-8 (LOCK) - E81-35 (SG-5)
    L - G
    Air compressor lock sensor signal
    Engine idling
    A/C switch: ON
    Blower switch LO
    Pulse generation
    (see waveform 1)
    E81-39 (CFN+) - Body ground
    R - Body ground
    Condenser FAN operation signal
    Engine switch on (IG)
    A/C switch: OFF
    Below 1 V
    Engine switch on (IG)
    A/C switch: ON
    11 to 14 V
    E81-15 (COOL) - Body ground
    W - Body ground
    Cool box operation signal
    Engine switch on (IG)
    Cool box switch: OFF
    Below 1 V
    Engine switch on (IG)
    Cool box switch: ON
    11 to 14 V
    E81-17 (AC1) - Body ground
    L - Body ground
    Compressor operation signal
    Engine switch on (IG)
    A/C switch: OFF
    Below 1 V
    Engine switch on (IG)
    A/C switch: ON
    11 to 14 V
    E81-27 (ACT) - Body ground
    G - Body ground
    Compressor operation signal
    Engine switch on (IG)
    A/C switch: OFF
    Below 1 V
    Engine switch on (IG)
    A/C switch: ON
    11 to 14 V
    E81-5 (TAM) - E81-13 (SG-2)
    V - G
    Ambient temperature sensor signal
    Engine switch on (IG)
    Ambient temperature: 25°C (77°F)
    1.6 to 1.8 V
    Engine switch on (IG)
    Ambient temperature: 50°C (122°F)
    0.5 to 0.7 V
    E81-30 (S5-1) - E81-13 (SG-2)
    LG - G
    Power supply for pressure sensor
    Engine switch on (IG)
    4.5 to 5.5 V
    E81-9 (PRE) - E81-13 (SG-2)
    R - G
    Air conditioning pressure sensor signal
    Refrigerant pressure: Normal
    1.0 to 4.8 V
    Refrigerant pressure: Abnormal (less than 0.392 MPa [4.0 kgf/cm2, 57 psi])
    Below 1 V
    Refrigerant pressure: Abnormal (less than 3.187 MPa [32.5 kgf/cm2, 463 psi])
    4.8 V or higher
    E81-20 (MGC) - E81-14 (GND)
    R - W-B
    A/C compressor magnetic clutch operation signal
    Engine idling
    Blower switch LO
    A/C switch: ON
    Below 1 V
    E81-18 (RCRL) - E81-14 (GND)
    B - Body ground
    Rear cooler control relay operation signal
    Engine switch on (IG)
    Rear blower switch OFF
    Below 1 V
    Engine switch on (IG)
    Rear blower switch ON
    11 to 14 V
    E81-23 (BLW) - E81-14 (GND)
    R - W-B
    Blower motor control signal
    Engine switch on (IG)
    Blower switch ON
    Pulse generation
    (see waveform 2)
    E81-29 (TR) - E81-34 (SG-1)
    W - B
    Room temperature sensor signal (for front)
    Engine switch on (IG)
    Front side interior temperature: 25°C (77°F)
    1.6 to 1.8 V
    Engine switch on (IG)
    Front side interior temperature: 50°C (122°F)
    0.5 to 0.7 V
    E81-32 (TSP) - Body ground
    GR - Body ground
    Passenger side solar sensor signal
    Engine switch on (IG)
    Solar sensor subjected to electric light
    0.8 to 4.3 V
    E81-33 (TSD) - Body ground
    LG - Body ground
    Driver side solar sensor signal
    Engine switch on (IG)
    Solar sensor subjected to electric light
    0.8 to 4.3 V
    E81-36 (SW1) - Body ground
    BR - Body ground
    Idle up operation signal
    Engine switch on (IG)
    Idle up switch OFF
    Below 1 V
    Engine switch on (IG)
    Idle up switch ON
    11 to 14 V
    z54-6 (TEA) - z54-5 (SGA)
    -
    Evaporator temperature sensor signal
    Engine switch on (IG)
    Evaporate temperature: 15°C (59°F)
    1.4 to 1.8 V
    z54-3 (BUS) - z54-2 (BUS G)
    -
    BUS IC control signal (for front)
    Engine switch on (IG)
    Pulse generation
    E81-37 (LIN1) - E81-14 (GND)
    Y - W-B
    LIN communication signal
    Engine switch on (IG)
    Pulse generation
    E81-25 (ALT) - Body ground
    R - Body ground
    Generator signal
    Engine idling
    Pulse generation
    E81-3 (PTC1) - Body ground
    R - Body ground
    PTC1 heater relay operation signal
    Engine idling
    Set temperature: MAX HOT
    Engine coolant temperature: Below 65°C (149°F)
    Ambient temperature: Below 10°C (50°F)
    Below 1 V → 11 to 14 V
    E81-22 (PTC2) - Body ground
    R - Body ground
    PTC2 heater relay operation signal
    E81-4 (PTC3) - Body ground
    R - Body ground
    PTC3 heater relay operation signal
    E81-24 (MGCA) - E81-14 (GND)
    Y - W-B
    Viscous with magnetic clutch operation signal
    Engine idling
    Idle up switch ON
    Below 1 V
    1. If the result is not as specified, the air conditioning amplifier or fuse may have a malfunction.

  5. E157042E01
    Using an oscilloscope, check waveform 1.
    A/C Compressor Lock Sensor Signal 
    Item
    Content
    Terminal No. (Symbol)
    E81-8 (LOCK) - E81-35 (SG-5)
    Tool Setting
    200 mV/DIV., 10 ms/DIV.
    Condition
    Engine running
    Blower switch LO
    A/C switch on

    HINT:
    When the rear blower level is increased, the duty ratio changes accordingly.

  6. E103396E12
    Using an oscilloscope, check waveform 2.
    Blower Motor Control Signal 
    Item
    Content
    Terminal No. (Symbol)
    E81-23 (BLW) - E81-14 (GND)
    Tool Setting
    1 V/DIV., 500 μs/DIV.
    Condition
    Engine switch on (IG)
    Blower switch LO

    HINT:
    When the blower level is increased, the duty ratio changes accordingly.


CHECK AIR CONDITIONING CONTROL ASSEMBLY (w/o Navigation System)
B185502E01
  1. Disconnect the F10 air conditioning control assembly connector.

  2. Measure the resistance and voltage according to the value(s) in the table below.

    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    F10-7 (IG+) - F10-1 (GND)
    G - W-B
    Ignition power supply
    Engine switch on (IG)
    11 to 14 V
    Engine switch off
    Below 1 V
    F10-1 (GND) - Body ground
    W-B - Body ground
    Ground
    Always
    Below 1 Ω
    1. If the result is not as specified, there may be a malfunction on the wire harness side.

  3. Reconnect the F10 air conditioning control assembly connector.

  4. Measure the resistance and voltage according to the value(s) in the table below.

    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    F10-12 (DTP+) - F10-1 (GND)
    R - W-B
    Temperature up switch signal
    Switch not pressed
    Below 1 V
    Switch pressed
    Alternating between 3.5 V or higher and below 1 V
    F10-10 (PTP+) - F10-1 (GND)
    L - W-B
    Temperature up switch signal
    Switch not pressed
    Below 1 V
    Switch pressed
    Alternating between 3.5 V or higher and below 1 V
    F10-9 (S5) - F10-1 (GND)
    B - W-B
    Signal ground
    Always
    Below 1 Ω
    F10-11 (DTP-) - F10-1 (GND)
    G - W-B
    Temperature down switch signal
    Switch not pressed
    Below 1 V
    Switch pressed
    Alternating between 3.5 V or higher and below 1 V
    F10-3 (PTP-) - F10-1 (GND)
    W - W-B
    Temperature down switch signal
    Switch not pressed
    Below 1 V
    Switch pressed
    Alternating between 3.5 V or higher and below 1 V
    F10-2 (SG) - F10-1 (GND)
    GR - W-B
    Signal ground
    Always
    Below 1 Ω
    1. If the result is not as specified, the air conditioning control assembly may have a malfunction.


CHECK DISPLAY AND NAVIGATION MODULE DISPLAY (w/ Navigation System)
E191986E01
  1. Disconnect the F64 display and navigation module display connector.

  2. Measure the resistance and voltage according to the value(s) in the table below.

    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    F64-3 (IG) - F64-10 (GND1)
    G - W-B
    Ignition power supply
    Engine switch on (IG)
    11 to 14 V
    Engine switch off
    Below 1 V
    F64-1 (+B1) - F64-10 (GND1)
    R - W-B
    Battery power source
    Always
    11 to 14 V
    F64-10 (GND1) - Body ground
    W-B - Body ground
    Ground
    Always
    Below 1 Ω
    1. If the result is not as specified, there may be a malfunction on the wire harness side.

  3. Reconnect the F64 display and navigation module display connector.

  4. Measure the resistance and voltage according to the value(s) in the table below.

    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    F63-2 (TEC+) - F64-10 (GND1)
    R - W-B
    Temperature up switch signal
    Switch not pressed
    Below 1 V
    Switch pressed
    Alternating between 3.5 V or higher and below 1 V
    F63-3 (TES+) - F64-10 (GND1)
    L - W-B
    Temperature up switch signal
    Switch not pressed
    Below 1 V
    Switch pressed
    Alternating between 3.5 V or higher and below 1 V
    F63-6 (AGND) - F64-10 (GND1)
    B - N-B
    Signal ground
    Always
    Below 1 Ω
    F63-7 (TEC-) - F64-10 (GND1)
    G - W-B
    Temperature down switch signal
    Switch not pressed
    Below 1 V
    Switch pressed
    Alternating between 3.5 V or higher and below 1 V
    F63-8 (TES-) - F64-10 (GND1)
    W - W-B
    Temperature down switch signal
    Switch not pressed
    Below 1 V
    Switch pressed
    Alternating between 3.5 V or higher and below 1 V
    F63-9 (BGND) - F64-10 (GND1)
    GR - W-B
    Signal ground
    Always
    Below 1 Ω
    1. If the result is not as specified, the display and navigation module display may have a malfunction.


CHECK NO. 2 AIR CONDITIONING CONTROL ASSEMBLY
E160844E01
  1. Disconnect the E55 switch connector.

  2. Measure the resistance and voltage according to the value(s) in the table below.

    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    E55-6 (IG) - E55-1 (E)
    G - W-B
    Ignition power supply
    Always
    11 to 14 V
    E55-1 (E) - Body ground
    W-B - Body ground
    Ground
    Always
    Below 1 Ω
    If the result is not as specified, there may be a malfunction on the wire harness side.


CHECK MAIN BODY ECU (COWL SIDE JUNCTION BLOCK LH)
C172609E03
  1. Disconnect the 2A, 2B, and 2D ECU connectors.

  2. Measure the voltage and resistance according to the value(s) in the table below.

    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    2B-20 (BATB) - Body ground
    L - Body ground
    Battery power supply
    Always
    11 to 14 V
    2A-1 (ACC) - Body ground
    GR - Body ground
    ACC power supply
    Engine switch on (ACC)
    11 to 14 V
    2A-1 (ACC) - Body ground
    GR - Body ground
    ACC power supply
    Engine switch off
    Below 1 V
    2D-62 (GND2) - Body ground
    W-B - Body ground
    Ground
    Always
    Below 1 Ω
    If the result is not as specified, there may be a malfunction in the wire harness.

← PROBLEM SYMPTOMS TABLE (from Jan 2012)TERMINALS OF ECU (from Jan 2012) →