TERMINALS OF ECU
System information · Vehicles built from Jan 2012
Versions by build date: Sep 2011 – Dec 2011 from Jan 2012
| CHECK AIR CONDITIONING AMPLIFIER ASSEMBLY (w/ Rear Heater) |


Disconnect the E36 and E35 air conditioning amplifier assembly connectors.
Measure the voltage and resistance according to the value(s) in the table below.
Terminal No. (Symbol)
Wiring Color
Terminal Description
Condition
Specified Condition
E36-6 (+B1) - E36-1 (GND)
R - W-B
Battery power supply
Always
11 to 14 V
E36-7 (+B2) - E36-1 (GND)
R - W-B
Battery power supply
Always
11 to 14 V
E36-5 (IG+) - E36-1 (GND)
G - W-B
Ignition power supply
Engine switch on (IG)
11 to 14 V
Engine switch off
Below 1 V
E36-2 (E1) - Body ground
W-B - Body ground
Ground
Always
Below 1 Ω
E36-1 (GND) - Body ground
W-B - Body ground
Ground
Always
Below 1 Ω
E35-6 (E2) - Body ground
W-B - Body ground
Ground
Always
Below 1 Ω
- If the result is not as specified, there may be a malfunction on the wire harness side.
- If the result is not as specified, there may be a malfunction on the wire harness side.
Reconnect the E36 and E35 air conditioning amplifier assembly connectors.
Measure the voltage and waveform according to the value(s) in the table below.
Terminal No. (Symbol)
Wiring Color
Terminal Description
Condition
Specified Condition
z53-3 (B BUS) - z53-1 (BUS G)
-
Power supply for BUS IC (for front)
Always
11 to 14 V
z53-10 (B BUS) - z53-8 (BUS G)
-
Power supply for BUS IC (for front)
Always
11 to 14 V
E36-14 (RBBU) - E36-12 (RBUG)
L - BR
Power supply for BUS IC (for rear)
Always
11 to 14 V
E35-25 (TR3) - Body ground
V - Body ground
Power supply for driver side duct sensor
Engine switch on (IG)
Driver side duct sensor temperature: 25°C (77°F)
4.8 to 5.2 kΩ
E35-26 (TR4) - Body ground
W - Body ground
Power supply for front passenger side duct sensor
Engine switch on (IG)
Front passenger side duct sensor temperature: 25°C (77°F)
4.8 to 5.2 kΩ
E35-16 (SG-2) - Body ground
G - Body ground
Ground for pressure sensor
Always
Below 1 Ω
E35-29 (SG-5) - Body ground
G - Body ground
Ground for compressor signal
Always
Below 1 Ω
E35-32 (SG-1) - Body ground
B - Body ground
Ground for room temperature sensor (for front)
Always
Below 1 Ω
z53-6 (SGA) - Body ground
-
Ground for evaporator temperature sensor
Always
Below 1 Ω
z53-1 (BUS G) - Body ground
-
Ground for BUS IC (for front)
Always
Below 1 Ω
z53-8 (BUS G) - Body ground
-
Ground for BUS IC (for front)
Always
Below 1 Ω
E35-34 (SGND) - Body ground
BR - Body ground
Ground for driver side duct sensor
Always
Below 1 Ω
E35-12 (SG-9) - Body ground
L - Body ground
Ground for front passenger side duct sensor
Always
Below 1 Ω
E35-2 (SG-6) - Body ground
G - Body ground
Ground for room temperature sensor signal (for Rear LH and Rear RH)
Always
Below 1 Ω
E36-12 (RBUG) - Body ground
BR - Body ground
Ground for BUS IC (for rear)
Always
Below 1 Ω
E35-1 (SG) - Body ground
P - Body ground
Ground for evaporator temperature sensor signal (for Rear)
Always
Below 1 Ω
E36-25 (CFN+) - Body ground*1
R - Body ground
Condenser fan operation signal
Engine switch on (IG)
11 to 14 V
E36-33 (COOL) - Body ground
W - Body ground
Cool box operation signal
Engine switch on (IG)
Cool box switch: On
11 to 14 V
E36-29 (AC1) - Body ground
L - Body ground
Compressor operation signal
Engine switch on (IG)
Blower switch: Lo
A/C switch: Off
11 to 14 V
Engine switch on (IG)
Blower switch: Lo
A/C switch: On
Below 1 V
E36-22 (ACT) - Body ground
G - Body ground
Compressor operation signal
Engine switch on (IG)
Blower switch: Lo
A/C switch: Off or on (magnet clutch off)
Below 1 V
Engine switch on (IG)
Blower switch: Lo
A/C switch: On (magnet clutch on)
11 to 14 V
E35-28 (LOCK) - E35-29 (SG-5)
L - G
Air compressor lock sensor signal
Engine idling
A/C switch: On (magnet clutch on)
Blower switch: Lo
Pulse generation
(see waveform 1)
E35-10 (TAM) - E35-16 (SG-2)
V - G
Ambient temperature sensor signal
Engine switch on (IG)
Ambient temperature:
25°C (77°F)
1.6 to 1.8 V
Engine switch on (IG)
Ambient temperature:
50°C (122°F)
0.5 to 0.7 V
E35-27 (S5-1) - E35-16 (SG-2)
LG - G
Power supply for pressure sensor
Engine switch on (IG)
4.5 to 5.5 V
E35-20 (PRE) - E35-16 (SG-2)
R - G
Air conditioning pressure sensor signal
Refrigerant pressure:
Normal
1.0 to 4.8 V
Refrigerant pressure:
Abnormal (less than 0.392 MPa [4.0 kgf/cm2, 57 psi])
Below 1 V
Refrigerant pressure:
Abnormal (less than 3.187 MPa [32.5 kgf/cm2, 463 psi])
4.8 V or higher
E36-18 (MGC) - E36-1 (GND)
R - W-B
Compressor magnet clutch operation signal
Engine idling
Blower switch: Lo
A/C switch: On (magnet clutch on permitted)
Below 1 V
E36-3 (BLW) - E36-1 (GND)
R - W-B
Blower motor control signal
Engine switch on (IG)
Blower switch: Lo
Pulse generation
(see waveform 2)
E35-9 (TR) - E35-32 (SG-1)
W - B
Room temperature sensor signal (for front)
Engine switch on (IG)
Front side interior temperature: 25°C (77°F)
1.6 to 1.8 V
Room temperature sensor signal (for front)
Engine switch on (IG)
Front side interior temperature: 50°C (122°F)
0.5 to 0.7 V
E35-7 (TSD) - Body ground
LG - Body ground
Driver side solar sensor signal
Engine switch on (IG)
Solar sensor subjected to electric light
0.8 to 4.3 V
E35-8 (TSP) - Body ground
GR - Body ground
Passenger side solar sensor signal
Engine switch on (IG)
Solar sensor subjected to electric light
0.8 to 4.3 V
z53-7 (TEA) - z53-6 (SGA)
-
Evaporator temperature sensor signal
Engine switch on (IG)
Evaporator temperature: 15°C (59°F)
1.4 to 1.8 V
z53-2 (BUS) - z53-1 (BUS G)
-
BUS IC control signal (for front)
Engine switch on (IG)
Pulse generation
z53-9 (BUS) - z53-8 (BUS G)
-
BUS IC control signal (for front)
Engine switch on (IG)
Pulse generation
E35-18 (TR) - E35-2 (SG-6)
R - G
Room temperature sensor signal (for Rear LH)
Engine switch on (IG)
Vehicle interior temperature: 25°C (77°F)
1.6 to 1.8 V
Engine switch on (IG)
Vehicle interior temperature: 50°C (122°F)
0.5 to 0.7 V
E35-19 (TR7) - E35-2 (SG-6)
R - G
Room temperature sensor signal (for Rear RH)
Engine switch on (IG)
Vehicle interior temperature: 25°C (77°F)
1.6 to 1.8 V
Engine switch on (IG)
Vehicle interior temperature: 50°C (122°F)
0.5 to 0.7 V
E36-13 (RBUS) - E36-12 (RBUG)
R - BR
BUS IC control signal (for rear)
Engine switch on (IG)
Pulse generation
E35-17 (TEC) - E35-1 (SG)
W - P
Evaporator temperature sensor signal (for Rear)
Engine switch on (IG)
Evaporator temperature:
15°C (59°F)
1.4 to 1.8 V
E36-31 (ALT) - Body ground
R - Body ground
Generator signal
Engine idling
Pulse generation
E36-32 (SW1) - Body ground
BR - Body ground
Idle up operation signal
Engine switch on (IG)
Idle up switch: Off
Below 1 V
Engine switch on (IG)
Idle up switch: On
11 to 14 V
E36-20 (LIN1) - E36-1 (GND)
Y - W-B
LIN communication signal
(for A/C switch)
Engine switch on (IG)
Pulse generation
E36-21 (RLIN) - E36-1 (GND)
L - W-B
LIN communication signal
(for Rear A/C switch)
Engine switch on (IG)
Pulse generation
E36-27 (PTC1) - Body ground*2
W - Body ground
PTC1 heater relay operation signal
Engine idling
Set temperature: MAX HOT
Engine coolant temperature: Below 65°C (149°F)
Ambient temperature: Below 10°C (50°F)
Blower switch: Off → Lo
Below 1 V → 11 to 14 V
E36-26 (PTC2) - Body ground*2
R - Body ground
PTC2 heater relay operation signal
E36-35 (PTC3) - Body ground*2
R - Body ground
PTC3 heater relay operation signal
E36-17 (BLWH) - E36-1 (GND)
L - W-B
Blower motor control signal (for rear)
Engine switch on (IG)
Blower switch: Lo
Pulse generation
(see waveform 3)
E36-19 (RMGV) - E36-1 (GND)
B - W-B
Rear cooling unit expansion valve signal
Engine switch on (IG)
11 to 14 V
- *1: w/ Condenser Fan
- *2: w/ PTC Heater
- *1: w/ Condenser Fan
Using an oscilloscope, check waveform 1.

Compressor Lock Sensor Signal Item
Content
Terminal No. (Symbol)
E35-28 (LOCK) - E35-29 (SG-5)
Tool Setting
200 mV/DIV., 10 ms/DIV.
Condition
Engine idling
Blower switch: Lo
A/C switch: On
- HINT:
- When the rear blower level is increased, the duty ratio changes accordingly.
Using an oscilloscope, check waveform 2.

Blower Motor Control Signal Item
Content
Terminal No. (Symbol)
E36-3 (BLW) - E36-1 (GND)
Tool Setting
1 V/DIV., 500 μs/DIV.
Condition
Engine switch on (IG)
Blower switch: Lo
- HINT:
- When the blower level is increased, the duty ratio changes accordingly.
Using an oscilloscope, check waveform 3.

Rear Blower Motor Control Signal Item
Content
Terminal No. (Symbol)
E36-17 (BLWH) - E36-1 (GND)
Tool Setting
1 V/DIV., 500 μs/DIV.
Condition
Engine switch on (IG)
Blower switch: Lo
- HINT:
- When the rear blower level is increased, the duty ratio changes accordingly.
| CHECK AIR CONDITIONING AMPLIFIER ASSEMBLY (w/o Rear Heater) |


Disconnect the E81 air conditioning amplifier assembly connector.
Measure the resistance and voltage according to the value(s) in the table below.
Terminal No. (Symbol)
Wiring Color
Terminal Description
Condition
Specified Condition
E81-21 (+B1) - E81-14 (GND)
R - W-B
Battery power supply
Always
11 to 14 V
E81-1 (IG+) - E81-14 (GND)
G - W-B
Ignition power supply
Engine switch on (IG)
11 to 14 V
Engine switch off
Below 1 V
E81-14 (GND) - Body ground
W-B - Body ground
Ground
Always
Below 1 Ω
- If the result is not as specified, there may be a malfunction on the wire harness side.
- If the result is not as specified, there may be a malfunction on the wire harness side.
Reconnect the E81 air conditioning amplifier assembly connector.
Measure the voltage and waveform according to the value(s) in the table below.
Terminal No. (Symbol)
Wiring Color
Terminal Description
Condition
Specified Condition
z54-4 (B BUS) - z54-2 (BUS G)
-
Power supply for BUS IC (for front)
Always
11 to 14 V
E81-35 (SG-5) - Body ground
G - Body ground
Ground for compressor signal
Always
Below 1 Ω
E81-13 (SG-2) - Body ground
G - Body ground
Ground for pressure sensor
Always
Below 1 Ω
E81-34 (SG-1) - Body ground
B - Body ground
Ground for room temperature sensor (for front)
Always
Below 1 Ω
z54-2 (BUS G) - Body ground
-
Ground for BUS IC (for front)
Always
Below 1 Ω
z54-5 (SGA) - Body ground
-
Ground for evaporator temperature sensor
Always
Below 1 Ω
E81-8 (LOCK) - E81-35 (SG-5)
L - G
Air compressor lock sensor signal
Engine idling
A/C switch: On (magnet clutch on)
Blower switch: Lo
Pulse generation
(see waveform 1)
E81-39 (CFN+) - Body ground*1
R - Body ground
Condenser fan operation signal
Engine switch on (IG)
A/C switch: Off
Below 1 V
Engine switch on (IG)
A/C switch: On
11 to 14 V
E81-15 (COOL) - Body ground
W - Body ground
Cool box operation signal
Engine switch on (IG)
Cool box switch: Off
Below 1 V
Engine switch on (IG)
Cool box switch: On
11 to 14 V
E81-17 (AC1) - Body ground
L - Body ground
Compressor operation signal
Engine switch on (IG)
Blower switch: Lo
A/C switch: Off
Below 1 V
Engine switch on (IG)
Blower switch: Lo
A/C switch: On
11 to 14 V
E81-27 (ACT) - Body ground
G - Body ground
Compressor operation signal
Engine switch on (IG)
Blower switch: Lo
A/C switch: Off or on (magnet clutch off)
Below 1 V
Engine switch on (IG)
Blower switch: Lo
A/C switch: On (magnet clutch on)
11 to 14 V
E81-5 (TAM) - E81-13 (SG-2)
V - G
Ambient temperature sensor signal
Engine switch on (IG)
Ambient temperature: 25°C (77°F)
1.6 to 1.8 V
Engine switch on (IG)
Ambient temperature: 50°C (122°F)
0.5 to 0.7 V
E81-30 (S5-1) - E81-13 (SG-2)
LG - G
Power supply for pressure sensor
Engine switch on (IG)
4.5 to 5.5 V
E81-9 (PRE) - E81-13 (SG-2)
R - G
Air conditioning pressure sensor signal
Refrigerant pressure: Normal
1.0 to 4.8 V
Refrigerant pressure: Abnormal (less than 0.392 MPa [4.0 kgf/cm2, 57 psi])
Below 1 V
Refrigerant pressure: Abnormal (less than 3.187 MPa [32.5 kgf/cm2, 463 psi])
4.8 V or higher
E81-20 (MGC) - E81-14 (GND)
R - W-B
Compressor magnet clutch operation signal
Engine idling
Blower switch: Lo
A/C switch: On (magnet clutch on permitted)
Below 1 V
E81-18 (RCRL) - E81-14 (GND)
B - Body ground
Rear cooler control relay operation signal
Engine switch on (IG)
Rear blower switch: Off
Below 1 V
Engine switch on (IG)
Rear blower switch: Lo
11 to 14 V
E81-23 (BLW) - E81-14 (GND)
R - W-B
Blower motor control signal
Engine switch on (IG)
Blower switch: Lo
Pulse generation
(see waveform 2)
E81-29 (TR) - E81-34 (SG-1)
W - B
Room temperature sensor signal (for front)
Engine switch on (IG)
Front side interior temperature: 25°C (77°F)
1.6 to 1.8 V
Engine switch on (IG)
Front side interior temperature: 50°C (122°F)
0.5 to 0.7 V
E81-32 (TSP) - Body ground
GR - Body ground
Passenger side solar sensor signal
Engine switch on (IG)
Solar sensor subjected to electric light
0.8 to 4.3 V
E81-33 (TSD) - Body ground
LG - Body ground
Driver side solar sensor signal
Engine switch on (IG)
Solar sensor subjected to electric light
0.8 to 4.3 V
E81-36 (SW1) - Body ground
BR - Body ground
Idle up operation signal
Engine switch on (IG)
Idle up switch: Off
Below 1 V
Engine switch on (IG)
Idle up switch: On
11 to 14 V
z54-6 (TEA) - z54-5 (SGA)
-
Evaporator temperature sensor signal
Engine switch on (IG)
Evaporate temperature: 15°C (59°F)
1.4 to 1.8 V
z54-3 (BUS) - z54-2 (BUS G)
-
BUS IC control signal (for front)
Engine switch on (IG)
Pulse generation
E81-37 (LIN1) - E81-14 (GND)
Y - W-B
LIN communication signal
Engine switch on (IG)
Pulse generation
E81-25 (ALT) - Body ground
R - Body ground
Generator signal
Engine idling
Pulse generation
E81-3 (PTC1) - Body ground*2
W - Body ground
PTC1 heater relay operation signal
Engine idling
Set temperature: MAX HOT
Engine coolant temperature: Below 65°C (149°F)
Ambient temperature: Below 10°C (50°F)
Below 1 V → 11 to 14 V
E81-22 (PTC2) - Body ground*2
R - Body ground
PTC2 heater relay operation signal
E81-4 (PTC3) - Body ground*2
R - Body ground
PTC3 heater relay operation signal
E81-24 (MGCA) - E81-14 (GND)
Y - W-B
Viscous with magnet clutch operation signal
Engine idling
Idle up switch: On
Below 1 V
- *1: w/ Condenser Fan
- *2: w/ PTC Heater
- *1: w/ Condenser Fan
Using an oscilloscope, check waveform 1.

Compressor Lock Sensor Signal Item
Content
Terminal No. (Symbol)
E81-8 (LOCK) - E81-35 (SG-5)
Tool Setting
200 mV/DIV., 10 ms/DIV.
Condition
Engine idling
Blower switch: Lo
A/C switch: On
- HINT:
- When the rear blower level is increased, the duty ratio changes accordingly.
Using an oscilloscope, check waveform 2.

Blower Motor Control Signal Item
Content
Terminal No. (Symbol)
E81-23 (BLW) - E81-14 (GND)
Tool Setting
1 V/DIV., 500 μs/DIV.
Condition
Engine switch on (IG)
Blower switch: Lo
- HINT:
- When the blower level is increased, the duty ratio changes accordingly.
| CHECK AIR CONDITIONING CONTROL ASSEMBLY (w/o Navigation System) |


Disconnect the F10 air conditioning control assembly connector.
Measure the resistance and voltage according to the value(s) in the table below.
Terminal No. (Symbol)
Wiring Color
Terminal Description
Condition
Specified Condition
F10-7 (IG+) - F10-1 (GND)
G - W-B
Ignition power supply
Engine switch on (IG)
11 to 14 V
Engine switch off
Below 1 V
F10-1 (GND) - Body ground
W-B - Body ground
Ground
Always
Below 1 Ω
- If the result is not as specified, there may be a malfunction on the wire harness side.
- If the result is not as specified, there may be a malfunction on the wire harness side.
Reconnect the F10 air conditioning control assembly connector.
Measure the resistance and voltage according to the value(s) in the table below.
Terminal No. (Symbol)
Wiring Color
Terminal Description
Condition
Specified Condition
F10-12 (DTP+) - F10-1 (GND)
R - W-B
Temperature up switch signal
Temperature up switch not pressed
Below 1 V
Temperature up switch pressed
Alternating between 3.5 V or higher and below 1 V
F10-10 (PTP+) - F10-1 (GND)
L - W-B
Temperature up switch signal
Temperature up switch not pressed
Below 1 V
Temperature up switch pressed
Alternating between 3.5 V or higher and below 1 V
F10-9 (S5) - F10-1 (GND)
B - W-B
Signal ground
Always
Below 1 Ω
F10-11 (DTP-) - F10-1 (GND)
G - W-B
Temperature down switch signal
Temperature down switch not pressed
Below 1 V
Temperature down switch pressed
Alternating between 3.5 V or higher and below 1 V
F10-3 (PTP-) - F10-1 (GND)
W - W-B
Temperature down switch signal
Temperature down switch not pressed
Below 1 V
Temperature down switch pressed
Alternating between 3.5 V or higher and below 1 V
F10-2 (SG) - F10-1 (GND)
GR - W-B
Signal ground
Always
Below 1 Ω
| CHECK NO. 2 AIR CONDITIONING CONTROL ASSEMBLY |


Disconnect the E55 air conditioning control assembly connector.
Measure the resistance and voltage according to the value(s) in the table below.
If the result is not as specified, there may be a malfunction on the wire harness side.Terminal No. (Symbol)
Wiring Color
Terminal Description
Condition
Specified Condition
E55-6 (IG) - E55-1 (E)
G - W-B
Ignition power supply
Always
11 to 14 V
E55-1 (E) - Body ground
W-B - Body ground
Ground
Always
Below 1 Ω
| CHECK MAIN BODY ECU (COWL SIDE JUNCTION BLOCK LH) |


Disconnect the 2A, 2B, and 2D ECU connectors.
Measure the voltage and resistance according to the value(s) in the table below.
Terminal No. (Symbol)
Wiring Color
Terminal Description
Condition
Specified Condition
2B-20 (BATB) - Body ground
L - Body ground
Battery power supply
Always
11 to 14 V
2A-1 (ACC) - Body ground
B - Body ground
ACC power supply
Engine switch on (ACC)
11 to 14 V
2A-1 (ACC) - Body ground
B - Body ground
ACC power supply
Engine switch off
Below 1 V
2D-62 (GND2) - Body ground
W-B - Body ground
Ground
Always
Below 1 Ω
- If the result is not as specified, there may be a malfunction on the wire harness side.
- If the result is not as specified, there may be a malfunction on the wire harness side.
| MULTI-DISPLAY ASSEMBLY (w/ Navigation System) |
![]() ![]() |
Measure the resistance and voltage according to the value(s) in the table below.
Terminal No. (Symbol)
Wiring Color
Terminal Description
Condition
Specified Condition
F90-2 (TEC+) - Body ground
R - Body ground
Temperature up switch signal
Temperature up switch not pressed
Below 1 V
Temperature up switch pressed
3.5 V or higher
F90-3 (TES+) - Body ground
L - Body ground
Temperature up switch signal
Temperature up switch not pressed
Below 1 V
Temperature up switch pressed
3.5 V or higher
F90-6 (AGND) - Body ground
B - Body ground
Signal ground
Always
Below 1 Ω
F90-7 (TEC-) - Body ground
G - Body ground
Temperature down switch signal
Temperature down switch not pressed
Below 1 V
Temperature down switch pressed
3.5 V or higher
F90-8 (TES-) - Body ground
W - Body ground
Temperature down switch signal
Temperature down switch not pressed
Below 1 V
Temperature down switch pressed
3.5 V or higher
F90-9 (BGND) - Body ground
GR - Body ground
Signal ground
Always
Below 1 Ω
| MULTI-MEDIA MODULE RECEIVER ASSEMBLY (w/ Navigation System) (Click here) |
