2011-2013 Land Cruiser · Service Manual Vehicle Interior

DATA LIST / ACTIVE TEST

System information · Vehicles built Sep 2011 – Dec 2011

Versions by build date: Sep 2011 – Dec 2011 from Jan 2012

HINT:
Using the intelligent tester to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.

NOTICE:
In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.


DATA LIST
  1. Connect the intelligent tester to the DLC3.

  2. Turn the ignition switch to ON.

  3. Turn the intelligent tester on.

  4. Enter the following menus: Body / Air Conditioner / Data List.

  5. Enter the following menus: Powertrain / Engine and ECT / Data List.

  6. According to the display on the intelligent tester, read the Data List.

    Air Conditioner 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Ambient Temp Sensor
    Cooler thermistor (ambient temperature sensor) /
    Min.: -23.3°C (-9.94°F)
    Max.: 65.95°C (150.71°F)
    Actual ambient temperature displayed
    Open in the circuit: -23.3°C (-9.94°F).
    Short in the circuit: 65.95°C (150.71°F).
    Adjusted Ambient Temp
    Adjusted ambient temperature /
    Min.: -30.8°C (-23.44°F)
    Max.: 50.8°C (123.44°F)
    Adjusted ambient temperature displayed
    -
    Evaporator Fin Thermistor
    No. 1 cooler thermistor /
    Min.: -29.7°C (-21.46°F)
    Max.: 59.55°C (139.19°F)
    Actual evaporator temperature displayed
    Open in the circuit: -29.7°C (-21.46°F).
    Short in the circuit: 59.55°C (139.19°F).
    Engine Coolant Temp
    Engine coolant temperature /
    Min.: 1.3°C (34.34°F)
    Max.: 90.55°C (194.99°F)
    Actual engine coolant temperature displayed while engine warmed up
    -
    Blower Motor Speed Level
    Blower with fan motor sub-assembly speed level /
    Min.: 0 level,
    Max.: 31 level
    Increases in range between 0 and 31 as blower with fan motor sub-assembly speed increases
    -
    Regulator Pressure Sensor
    Air conditioner pressure sensor /
    Min.: -0.4566 MPaG
    Max.: 3.2943 MPaG
    Actual refrigerant pressure displayed
    -
    Air Mix Servo Targ Pulse(D)
    No. 1 air conditioning radiator damper servo sub-assembly (air mix damper servo) target pulse /
    Min.: 0, Max.: 255
    for LHD
    1. MAX. COOL: 90 (pulse)
    2. MAX. HOT: 8 (pulse)
    for RHD
    1. MAX. COOL: 8 (pulse)
    2. MAX. HOT: 90 (pulse)
    -
    Air Outlet Servo Pulse(D)
    No. 1 air conditioning radiator damper servo sub-assembly (mode damper servo) target pulse /
    Min.: 0, Max.: 255
    1. FACE: 117 (pulse)
    2. B/L: 93 (pulse)
    3. FOOT: 41 (pulse)
    4. F/D: 18 (pulse)
    5. DEF: 6 (pulse)
    -
    Air Inlet Damper Targ Pulse
    No. 1 blower damper servo sub-assembly target pulse /
    Min.: 0, Max.: 255
    for LHD
    1. Recirculation: 37 (pulse)
    2. Fresh: 9 (pulse)
    for RHD
    1. Recirculation: 9 (pulse)
    2. Fresh: 37 (pulse)
    -
    Cool Air Bypass Pulse
    No. 1 air conditioning radiator damper servo sub-assembly (cooler bypass damper servo) target pulse /
    Min.: 0, Max.: 255
    1. Shut and DEF mode: 6 (pulse)
    2. Shut: 28 (pulse)
    3. Open: 57 (pulse)
    -
    Button Press Buzzer
    Button press buzzer / ON or OFF
    Customized value displayed
    -
    Ambient Temperature Shift
    Ambient temperature shift / +3 C, +2 C, +1 C, NORMAL, -1 C, -2 C, -3 C
    Customized value displayed
    -
    Pls Servo Test Sts
    Pulse servo motor test status / 00, 01, 02, 03, 04
    1. Not in effect: 00
    2. During test: 01
    3. Completed without malfunction: 02
    4. Completed with malfunction: 03
    5. Interrupted: 04
    -
    Number of Trouble Codes
    Number of trouble codes /
    Min.: 0, Max.: 255
    Number of DTCs displayed
    -
    Engine 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    A/C Signal
    Air conditioning signal / ON or OFF
    1. ON: A/C switch on
    2. OFF: A/C switch off
    -


ACTIVE TEST

HINT:
Using the intelligent tester to perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.

  1. Connect the intelligent tester to the DLC3.

  2. Turn the ignition switch to ON.

  3. Turn the intelligent tester on.

  4. Enter the following menus: Body / Air Conditioner / Active Test.

  5. According to the display on the intelligent tester, perform the Active Test.

    Tester Display
    Test Part
    Control Range
    Diagnostic Note
    Blower Motor
    Blower with fan motor sub-assembly
    Min.: 0, Max.: 31
    -
    Magnetic Clutch Relay
    Magnet clutch relay
    OFF or ON
    -
    Air Mix Servo Targ Pulse(D)
    No. 1 air conditioning radiator damper servo sub-assembly (air mix damper servo)
    Min.: 0, Max.: 255
    -
    Air Outlet Servo Pulse(D)
    No. 1 air conditioning radiator damper servo sub-assembly (mode damper servo)
    Min.: 0, Max.: 255
    -
    Air Inlet Damper Targ Pulse
    No. 1 blower damper servo sub-assembly
    Min.: 0, Max.: 255
    -
    Cool Air Bypass Pulse
    No. 1 air conditioning radiator damper servo sub-assembly (cooler bypass damper servo)
    Min.: 0, Max.: 255
    -

← DTC CHECK / CLEAR (from Sep 2011)DATA LIST / ACTIVE TEST (from Jan 2012) →