DATA LIST / ACTIVE TEST
System information · Vehicles built from Jan 2012
Versions by build date: Sep 2011 – Dec 2011 from Jan 2012
- HINT:
- Using the intelligent tester to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.
- NOTICE:
- In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.
| DATA LIST |
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Turn the intelligent tester on.
Enter the following menus: Body / Air Conditioner / Data List.
Enter the following menus: Powertrain / Engine and ECT / Data List.
According to the display on the intelligent tester, read the Data List.
Air Conditioner Tester Display
Measurement Item/Range
Normal Condition
Diagnostic Note
Ambient Temp Sensor
Cooler thermistor (ambient temperature sensor) /
Min.: -23.3°C (-9.94°F)
Max.: 65.95°C (150.71°F)
Actual ambient temperature displayed
Open in the circuit: -23.3°C (-9.94°F).
Short in the circuit: 65.95°C (150.71°F).
Adjusted Ambient Temp
Adjusted ambient temperature /
Min.: -30.8°C (-23.44°F)
Max.: 50.8°C (123.44°F)
Adjusted ambient temperature displayed
-
Evaporator Fin Thermistor
No. 1 cooler thermistor /
Min.: -29.7°C (-21.46°F)
Max.: 59.55°C (139.19°F)
Actual evaporator temperature displayed
Open in the circuit: -29.7°C (-21.46°F).
Short in the circuit: 59.55°C (139.19°F).
Engine Coolant Temp
Engine coolant temperature /
Min.: 1.3°C (34.34°F)
Max.: 90.55°C (194.99°F)
Actual engine coolant temperature displayed while engine warmed up
-
Blower Motor Speed Level
Blower with fan motor sub-assembly speed level /
Min.: 0 level,
Max.: 31 level
Increases in range between 0 and 31 as blower with fan motor sub-assembly speed increases
-
Regulator Pressure Sensor
Air conditioner pressure sensor /
Min.: -0.4566 MPaG
Max.: 3.2943 MPaG
Actual refrigerant pressure displayed
-
Air Mix Servo Targ Pulse(D)
No. 1 air conditioning radiator damper servo sub-assembly (air mix damper servo) target pulse /
Min.: 0, Max.: 255
for LHD- MAX. COOL: 90 (pulse)
- MAX. HOT: 8 (pulse)
for RHD- MAX. COOL: 8 (pulse)
- MAX. HOT: 90 (pulse)
-
Air Outlet Servo Pulse(D)
No. 1 air conditioning radiator damper servo sub-assembly (mode damper servo) target pulse /
Min.: 0, Max.: 255
- FACE: 117 (pulse)
- B/L: 93 (pulse)
- FOOT: 41 (pulse)
- F/D: 18 (pulse)
- DEF: 6 (pulse)
-
Air Inlet Damper Targ Pulse
No. 1 blower damper servo sub-assembly target pulse /
Min.: 0, Max.: 255
for LHD- Recirculation: 37 (pulse)
- Fresh: 9 (pulse)
for RHD- Recirculation: 9 (pulse)
- Fresh: 37 (pulse)
-
Cool Air Bypass Pulse
No. 1 air conditioning radiator damper servo sub-assembly (cooler bypass damper servo) target pulse /
Min.: 0, Max.: 255
- Shut and DEF mode: 6 (pulse)
- Shut: 28 (pulse)
- Open: 57 (pulse)
-
Electric Heater Count*
Number of electrical heaters operating /
Min.: 0, Max.: 3
Aetual heater counts displayed
-
Ambient Temperature Shift
Ambient temperature shift / +3 C, +2 C, +1 C, NORMAL, -1 C, -2 C, -3 C
Customized value displayed
-
Pls Servo Test Sts
Pulse servo motor test status / 00, 01, 02, 03, 04
- Not in effect: 00
- During test: 01
- Completed without malfunction: 02
- Completed with malfunction: 03
- Interrupted: 04
-
Number of Trouble Codes
Number of trouble codes /
Min.: 0, Max.: 255
Number of DTCs displayed
-
Engine Tester Display
Measurement Item/Range
Normal Condition
Diagnostic Note
A/C Signal
Air conditioning signal / ON or OFF
- ON: A/C switch on
- OFF: A/C switch off
-
- *: w/ PTC Heater
- MAX. COOL: 90 (pulse)
| ACTIVE TEST |
- HINT:
- Using the intelligent tester to perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Turn the intelligent tester on.
Enter the following menus: Body / Air Conditioner / Active Test.
According to the display on the intelligent tester, perform the Active Test.
Tester Display
Test Part
Control Range
Diagnostic Note
Blower Motor
Blower with fan motor sub-assembly
Min.: 0, Max.: 31
-
Magnetic Clutch Relay
Magnet clutch relay
OFF or ON
-
Heater Active Lerel*
Quick heater assembly
Min.: 0, Max.: 3
Air Mix Servo Targ Pulse(D)
No. 1 air conditioning radiator damper servo sub-assembly (air mix damper servo)
Min.: 0, Max.: 255
-
Air Outlet Servo Pulse(D)
No. 1 air conditioning radiator damper servo sub-assembly (mode damper servo)
Min.: 0, Max.: 255
-
Air Inlet Damper Targ Pulse
No. 1 blower damper servo sub-assembly
Min.: 0, Max.: 255
-
Cool Air Bypass Pulse
No. 1 air conditioning radiator damper servo sub-assembly (cooler bypass damper servo)
Min.: 0, Max.: 255
-
- *: w/ PTC Heater
- *: w/ PTC Heater