2011-2013 Land Cruiser · Service Manual Vehicle Interior

B1411/11 Room Temperature Sensor Circuit

Diagnostic trouble codes · Vehicles built Sep 2011 – Dec 2011

Versions by build date: Sep 2011 – Dec 2011 from Jan 2012

DESCRIPTION

The front room temperature sensor for the front seat is installed in the instrument panel to detect the room temperature and control the heater and air conditioner "auto" mode. The resistance of the room temperature sensor changes in accordance with the front room temperature. As the temperature decreases, the resistance increases. As the temperature increases, the resistance decreases.
The air conditioning amplifier assembly applies voltage (5 V) to the front room temperature sensor and reads voltage changes as the resistance of the front room temperature sensor changes. This sensor also sends the appropriate signals to the air conditioning amplifier assembly.
DTC Code
DTC Detection Condition
Trouble Area
B1411/11
An open or short in the front room temperature sensor circuit.
  1. Front room temperature sensor
  2. Harness or connector between room temperature sensor and air conditioning amplifier assembly
  3. Air conditioning amplifier assembly

WIRING DIAGRAM

E156584E44
E156584E45

INSPECTION PROCEDURE


1. READ VALUE USING INTELLIGENT TESTER (FRONT ROOM TEMPERATURE SENSOR)
  1. Use the Data List to check if the front room temperature sensor is functioning properly.

    Air Conditioner 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Room Temperature Sensor
    Front room temperature sensor /
    Min.: -6.5°C (20.3°F)
    Max.: 57.25°C (135.05°F)
    Actual room temperature for front seat displayed
    Open in the circuit: -6.5°C (20.3°F).
    Short in the circuit: 57.25°C (135.05°F).

    OK:
    The display is as specified in the normal condition.



NG
Go to step 2
OK

REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY (Click here)

2. INSPECT ROOM TEMPERATURE SENSOR
E160595E02
  1. Remove the front room temperature sensor (Click here).

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    1 (+) - 2 (-)
    10°C (50°F)
    3.00 to 3.73 kΩ
    15°C (59°F)
    2.45 to 2.88 kΩ
    20°C (68°F)
    1.95 to 2.30 kΩ
    25°C (77°F)
    1.60 to 1.80 kΩ
    30°C (86°F)
    1.28 to 1.47 kΩ
    35°C (95°F)
    1.00 to 1.22 kΩ
    40°C (104°F)
    0.80 to 1.00 kΩ
    45°C (113°F)
    0.65 to 0.85 kΩ
    50°C (122°F)
    0.50 to 0.70 kΩ
    55°C (131°F)
    0.44 to 0.60 kΩ
    60°C (140°F)
    0.36 to 0.50 kΩ

    NOTICE:
    1. Even slightly touching the sensor may change the resistance value. Be sure to hold the connector of the sensor.
    2. When measuring, the sensor temperature must be the same as the ambient temperature.

    HINT:
    As the temperature increases, the resistance decreases (see the graph).



NG
REPLACE FRONT ROOM TEMPERATURE SENSOR (Click here)
OK


3. CHECK HARNESS AND CONNECTOR (FRONT ROOM TEMPERATURE SENSOR - AIR CONDITIONING AMPLIFIER)

  1. E156619E03
    w/ Rear Heater
    1. Disconnect the E32 sensor connector.

    2. Disconnect the E35 amplifier connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      E32-1 (+) - E35-9 (TR)
      Always
      Below 1 Ω
      E32-2 (-) - E35-32 (SG-1)
      E35-9 (TR) - Body ground
      Always
      10 kΩ or higher
      E35-32 (SG-1) - Body ground

  1. E160288E03
    w/o Rear Heater
    1. Disconnect the E32 sensor connector.

    2. Disconnect the E81 amplifier connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      E32-1 (+) - E81-29 (TR)
      Always
      Below 1 Ω
      E32-2 (-) - E81-34 (SG-1)
      E81-29 (TR) - Body ground
      Always
      10 kΩ or higher
      E81-34 (SG-1) - Body ground



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY (Click here)


← ACTUATOR CHECK (from Sep 2011)B1411/11 Room Temperature Sensor Circuit (from Jan 2012) →