2011-2013 Land Cruiser · Service Manual Vehicle Interior

INSTALLATION

Removal / installation · Vehicles built from Jan 2012

Versions by build date: Sep 2011 – Dec 2011 from Jan 2012

HINT:
  1. Use the same procedure for the RH and LH sides.
  2. The procedure listed below is for the LH side.
  3. A bolt without a torque specification is shown in the standard bolt chart (Click here).


1. INSTALL FRONT SHOULDER BELT ANCHOR ADJUSTER ASSEMBLY

B184509
  1. Align the adjuster positioning hole with the claw, and install the adjuster with the 2 bolts.

    HINT:
    First install the lower bolt, and then install the upper bolt.

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }


2. INSTALL FRONT SEAT OUTER BELT ASSEMBLY

B180625E01

NOTICE:
When installing the retractor, make sure the claws of the vehicle (labeled "a" in the illustration) only contact the installation areas of the retractor.

  1. Align the claws of the vehicle with the seat belt retractor positioning holes.

  1. Install the seat belt with the bolt.

    Torque:
    8.5 N*m{ 87 kgf*cm , 75 in.*lbf }

  1. B180626E01
    Connect the pretensioner connector labeled A as shown in the illustration.

  1. Connect the tension reducer connector labeled B.

  1. w/ Pre-Crash Safety System:
    Connect the pre-crash safety connector labeled C.

  1. B180622
    Install the shoulder anchor to the shoulder belt anchor adjuster with the nut.

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }


3. INSTALL CENTER PILLAR GARNISH LH

B181681
  1. Pass the seat belt anchor through the center pillar garnish.

  1. Attach the 2 clips and 2 guides to install the center pillar garnish.

  1. Install the bolt.


4. INSTALL REAR ASSIST GRIP ASSEMBLY

B181680

HINT:
Use the same procedure to install the rear assist grip on the other side.

  1. Attach the 2 claws to install the rear assist grip.

  1. Install the 2 bolts.

  1. B181679
    Attach the 4 claws to install the 2 assist grip plugs.


5. INSTALL CENTER LOWER PILLAR GARNISH

B181678

HINT:
  1. for Manual Seat:
    When installing the center lower pillar garnish, move the front seat and seatback to the foremost upright position.
  2. for Power Seat:
    When installing the center pillar garnish cover, connect the cable to the negative (-) battery terminal and operate the power seat switch to move the front seat and seatback to the foremost upright position.
  3. for Manual Seat:
    After moving the front seat, disconnect the cable from the negative (-) battery terminal.

  1. Attach the 2 claws and 7 clips to install the center lower pillar garnish.

  1. B181677
    Install the seat belt anchor with the bolt.

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }


6. INSTALL CENTER PILLAR GARNISH COVER

HINT:
  1. for Manual Seat:
    When installing the center lower pillar garnish, move the front seat and seatback to the foremost upright position.
  2. for Power Seat:
    When installing the center lower pillar garnish, connect the cable to the negative (-) battery terminal and operate the power seat switch to move the front seat and seatback to the foremost upright position.
  3. for Power Seat:
    After moving the front seat, disconnect the cable from the negative (-) battery terminal.

  1. B181678
    Attach the 2 claws and 7 clips to install the center lower pillar garnish.

  1. B181677
    Install the seat belt anchor with the bolt.

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }


7. INSTALL REAR DOOR SCUFF PLATE

B181682
  1. Attach the 7 claws and 4 clips to install the scuff plate.


8. INSTALL REAR STEP COVER

B181673

HINT:
Use the same procedure to install the step cover on the other side.

  1. Attach the 2 claws to install the step cover.


9. INSTALL FRONT DOOR SCUFF PLATE

B181682
  1. Attach the 7 claws and 4 clips to install the scuff plate.


10. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

NOTICE:
When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).


11. CHECK SRS WARNING LIGHT
(Click here)
← INSTALLATION (Sep 2011 – Dec 2011)DISPOSAL (Sep 2011 – Dec 2011) →