2011-2013 Land Cruiser · Service Manual Vehicle Interior

B1421/21 Solar Sensor Circuit (Passenger Side)

Diagnostic trouble codes · Vehicles built Sep 2011 – Dec 2011

DESCRIPTION

E132508E01
The automatic light control sensor (solar sensor), which is installed on the upper side of the instrument panel, detects sunlight and controls the air conditioning in auto mode. The output current from the solar sensor varies according to the amount of sunlight. When the sunlight increases, the output current increases. As the sunlight decreases, the output current decreases. The air conditioning amplifier assembly detects output current from the solar sensor.
DTC Code
DTC Detection Condition
Trouble Area
B1421/21
An open or short in the passenger side solar sensor circuit.
  1. Automatic light control sensor (solar sensor)
  2. Harness or connector between solar sensor and air conditioning amplifier assembly
  3. Harness or connector between solar sensor and main body ECU (cowl side junction block LH)
  4. Main body ECU (cowl side junction block LH)
  5. Air conditioning amplifier assembly

HINT:
If DTC B1244 is output at the same time, troubleshoot DTC B1244 first.


WIRING DIAGRAM

E160577E09
E160577E12

INSPECTION PROCEDURE


1. READ VALUE USING INTELLIGENT TESTER (PASSENGER SIDE SOLAR SENSOR)
  1. Use the Data List to check if the front passenger side solar sensor is functioning properly.

    Air Conditioner 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Solar Sensor (P Side)
    Passenger side solar sensor /
    Min.: 0, Max.: 255
    Passenger side solar sensor voltage increases as brightness increases
    Open in the circuit: 0.
    Short in the circuit: 255.

    OK:
    The display is as specified in the normal condition.



NG
Go to step 2
OK

REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY (Click here)

2. CHECK HARNESS AND CONNECTOR (AIR CONDITIONING AMPLIFIER - AUTOMATIC LIGHT CONTROL SENSOR)
E157179E03
  1. w/ Rear Heater

    1. Disconnect the F9 sensor connector.

    2. Disconnect the E35 amplifier connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      E35-8 (TSP) - F9-2 (TSR)*1
      Always
      Below 1 Ω
      E35-8 (TSP) - F9-1 (TSL)*2
      Always
      Below 1 Ω
      E35-8 (TSP) - Body ground
      Always
      10 kΩ or higher

      HINT:
      *1: for LHD
      *2: for RHD

  1. E160313E01
    w/o Rear Heater
    1. Disconnect the F9 sensor connector.

    2. Disconnect the E81 amplifier connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      E81-32 (TSP) - F9-2 (TSR)*1
      Always
      Below 1 Ω
      E81-32 (TSP) - F9-1 (TSL)*2
      Always
      Below 1 Ω
      E81-32 (TSP) - Body ground
      Always
      10 kΩ or higher

      HINT:
      *1: for LHD
      *2: for RHD



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


3. INSPECT AUTOMATIC LIGHT CONTROL SENSOR (TSR, TSL - CLTE VOLTAGE)
E108193E22
  1. Remove the automatic light control sensor (Click here).

  1. Apply battery voltage between terminals 6 (CLTB) and 3 (CLTE) of the solar sensor.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    2 (TSR) - 3 (CLTE)*1
    Sensor exposed to electric light
    0.8 to 4.3 V
    Sensor covered with a cloth
    Below 0.8 V
    1 (TSL) - 3 (CLTE)*2
    Sensor exposed to electric light
    0.8 to 4.3 V
    Sensor covered with a cloth
    Below 0.8 V

    HINT:
    1. As the inspection light is moved away from the sensor, the voltage decreases.
    2. Use an incandescent light for inspection. Bring it about 300 mm (11.8 in.) from the solar sensor.
    3. *1: for LHD
    4. *2: for RHD



NG
REPLACE AUTOMATIC LIGHT CONTROL SENSOR (Click here)
OK


4. CHECK HARNESS AND CONNECTOR (MAIN BODY ECU - AUTOMATIC LIGHT CONTROL SENSOR)
E157041E01
  1. Disconnect the E2 ECU connector.

  1. Disconnect the F9 sensor connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    E2-20 (CLTB) - F9-6 (CLTB)
    Always
    Below 1 Ω
    E2-19 (CLTS) - F9-5 (CLTS)
    E2-18 (CLTE) - F9-3 (CLTE)
    E2-20 (CLTB) - Body ground
    Always
    10 kΩ or higher
    E2-19 (CLTS) - Body ground
    E2-18 (CLTE) - Body ground



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE MAIN BODY ECU (COWL SIDE JUNCTION BLOCK LH)


← B1419/19 Rear Room Temperature Sensor Circuit (from Jan 2012)B1422/22 Compressor Lock Sensor Circuit (Sep 2011 – Dec 2011) →