2011-2013 Land Cruiser · Service Manual Vehicle Interior

Rear Blower Motor Circuit

Circuit diagnosis · Vehicles built from Sep 2011

DESCRIPTION

E157361E02
The rear blower motor (w/ rear heater) is operated by signals from the air conditioning amplifier assembly. The rear blower motor speed signals are transmitted by changes in the duty ratio.
Duty Ratio:
The duty ratio is the ratio of the rear blower motor OPEN time (T1) to the total of the rear blower motor OPEN and LO time (T2).
The rear blower motor controller controls the rear blower motor speed.

WIRING DIAGRAM

E157377E03

INSPECTION PROCEDURE


1. PERFORM ACTIVE TEST USING INTELLIGENT TESTER (REAR BLOWER MOTOR)
  1. Select the Active Test, use the intelligent tester to generate a control command, and then check that the rear blower motor operates.

    Air Conditioner 
    Tester Display
    Test Part
    Control Range
    Diagnostic Note
    Rear Blower Motor
    Rear blower motor
    Min.: 0, Max.: 31
    -
    Result 
    Result
    Proceed to
    Rear blower motor operates normally
    A
    Rear blower motor does not operate
    B
    Rear blower motor operates but does not change speed
    C



B
Go to step 2

C
Go to step 5
A

PROCEED TO NEXT CIRCUIT INSPECTION SHOWN IN PROBLEM SYMPTOMS TABLE (Click here)

2. CHECK HARNESS AND CONNECTOR (WIRING AIR CONDITIONING HARNESS - BODY GROUND)
E157378E01
  1. Disconnect the wiring air conditioning harness sub-assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    4 (GND) - Body ground
    Always
    Below 1 Ω



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


3. CHECK HARNESS AND CONNECTOR (WIRING AIR CONDITIONING HARNESS - BATTERY)
E157378E02
  1. Disconnect the wiring air conditioning harness sub-assembly connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    1 (+B) - Body ground
    Always
    11 to 14 V



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


4. CHECK WIRING AIR CONDITIONING HARNESS SUB-ASSEMBLY (SI VOLTAGE)
E157379E01
  1. Disconnect the E36 amplifier connector.

  1. Reconnect the wiring air conditioning harness sub-assembly connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    8 (SI) - Body ground
    Engine switch on (IG)
    4.5 to 5.5 V



NG
Go to step 7
OK


5. CHECK HARNESS AND CONNECTOR (AIR CONDITIONING AMPLIFIER - WIRING AIR CONDITIONING HARNESS)
E157362E03
  1. Disconnect the E36 amplifier connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    E36-17 (BLWH) - E36-1 (GND)
    Engine switch on (IG)
    Blower switch off
    4.5 to 5.5 V



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


6. CHECK AIR CONDITIONING AMPLIFIER ASSEMBLY (BLWH SIGNAL)

  1. E157363E02
    Remove the air conditioning amplifier assembly with its connectors still connected (Click here).

  1. Using an oscilloscope, check the waveform.

    Measurement Condition 
    Item
    Content
    Terminal No.(Symbol)
    E36-17 (BLWH) - E36-1 (GND)
    Tool Setting
    1 V/DIV., 500 μs/DIV.
    Condition
    Engine switch on (IG)
    Blower switch: off → on

    OK:
    Waveform is as shown in the illustration.

    HINT:
    Waveform varies with the blower level.



NG
REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY (Click here)
OK


7. CHECK WIRING AIR CONDITIONING HARNESS SUB-ASSEMBLY (OPERATION)
  1. Replace the wiring air conditioning harness sub-assembly with a normal one and check that the condition returns to normal.

    OK:
    Same problem does not occur.



NG
Go to step 8
OK

REPLACE WIRING AIR CONDITIONING HARNESS SUB-ASSEMBLY

8. INSPECT REAR BLOWER MOTOR

  1. E160302E01
    Disconnect the z32 motor connector.

  1. Connect the positive (+) lead of the battery to terminal 2 and the negative (-) lead to terminal 1, then check that the rear blower motor operates smoothly.

    OK:
    The rear blower motor operates smoothly.



NG
REPLACE REAR BLOWER MOTOR (Click here)
OK

REPLACE REAR BLOWER MOTOR CONTROLLER (Click here)


← PTC Heater Circuit (from Jan 2012)Rear Magnetic Valve Circuit (from Sep 2011) →