2011-2013 Land Cruiser · Service Manual Vehicle Exterior

INSTALLATION

Removal / installation · Vehicles built from Jan 2012

Versions by build date: Sep 2011 – Dec 2011 from Jan 2012


1. INSTALL SLIDING ROOF HOUSING SUB-ASSEMBLY
  1. Temporarily install the housing with the 8 bolts (vehicle body side) and 8 nuts.

  1. Tighten the 8 nuts.

    Torque:
    5.5 N*m{ 56 kgf*cm , 49 in.*lbf }

  1. Tighten the 8 bolts.

    Torque:
    5.5 N*m{ 56 kgf*cm , 49 in.*lbf }


    B178615


2. INSTALL SLIDING ROOF WEATHERSTRIP

B178628E01
  1. Install the sliding roof weatherstrip as described below.

    1. Attach each corner of the weatherstrip so that each weatherstrip mark is aligned with the sliding roof glass center mark. After attaching the entire weatherstrip, check that all weatherstrip marks are within the sliding roof glass end marks.

    2. Make sure the weatherstrip cutout is toward the rear side of the vehicle and centered.

    3. Make sure the weatherstrip is securely installed as shown in the illustration.


3. INSTALL SLIDING ROOF GLASS SUB-ASSEMBLY

  1. B178614
    Using a T25 "TORX" driver, temporarily install the glass with the 4 screws.

  1. Perform a level check.

    1. Check the difference in the level between the roof panel and the upper surface of the weatherstrip labeled "a" when the sliding roof glass is fully closed.

      Standard:
      Area
      Specified Condition
      A - A
      0 +/-1.5 mm (0 +/-0.0591 in.)
      B - B
      C - C
      D - D

      HINT:
      "+" represents the condition that the glass is above the panel level. "-" represents the condition that the glass is below the panel level.

    2. Perform a gap check.
      Check the gap between the roof panel and roof glass.

      NOTICE:
      The gap must be even all around.


      B178629E01

  1. B178614
    Tighten the 4 screws.

    Torque:
    5.5 N*m{ 56 kgf*cm , 49 in.*lbf }


4. CHECK FOR WATER LEAK
  1. After adjusting the sliding roof glass sub-assembly, check for water leaks.

  1. If there are any leaks, readjust the sliding roof glass sub-assembly.


5. INSTALL SLIDING ROOF SIDE GARNISH LH

B178613
  1. Attach the 5 claws to install the sliding roof side garnish.


6. INSTALL SLIDING ROOF SIDE GARNISH RH

HINT:
Use the same procedures described for the LH side.


7. INSTALL REAR NO. 5 ROOF AIR DUCT

  1. B178612
    Attach the 2 clips to install the duct.


8. INSTALL REAR NO. 4 ROOF AIR DUCT

HINT:
Use the same procedures described for the No. 5 roof air duct.


9. INSTALL CURTAIN SHIELD AIRBAG ASSEMBLY LH
  1. Install the curtain shield airbag (Click here).


10. INSTALL CURTAIN SHIELD AIRBAG ASSEMBLY RH

HINT:
Use the same procedures described for the LH side.


11. INSTALL ROOF HEADLINING ASSEMBLY
  1. Install the roof headlining (Click here).


12. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

NOTICE:
When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).


13. CHECK SRS WARNING LIGHT
  1. Check the SRS warning light (Click here).

← INSTALLATION (Sep 2011 – Dec 2011)PARTS LOCATION (from Jan 2012) →