2011-2013 Land Cruiser · Service Manual Vehicle Exterior

TERMINALS OF ECU

System information · Vehicles built Sep 2011 – Dec 2011

Versions by build date: Sep 2011 – Dec 2011 from Jan 2012


CHECK WINDSHIELD WIPER ECU
E157213E02
  1. Disconnect the E83 and E85 ECU connectors.

  2. Measure the voltage and resistance according to the value(s) in the table below.

    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    E83-5 (IG1l) - A50-6 (ES)
    G - W-B
    Power source
    Engine switch on (IG)
    11 to 14 V
    E85-10 (E) - Body ground
    W-B - Body ground
    Power ground
    Always
    Below 1 Ω
    If the result is not as specified, there may be a malfunction on the wire harness side.

  3. Reconnect the E83 and E85 ECU connectors.

  4. Measure the voltage according to the value(s) in the table below.

    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    E83-7 (+SM) - Body ground
    W - Body ground
    Front wiper motor operation signal
    Front wiper is operated
    11 to 14 V
    Front wiper is stopped
    Below 1 V
    E83-8 (WIG) - Body ground
    B - Body ground
    Front wiper motor power source circuit
    Engine switch off
    Below 1 V
    Engine switch on (IG)
    11 to 14 V
    E83-10 (1S) - Body ground
    G - Body ground
    Front wiper motor power supply circuit
    Front wiper switch off
    Below 1 V
    Front wiper switch LO
    11 to 14 V
    E83-9 (2S) - Body ground
    R - Body ground
    Front wiper motor power supply circuit (HI signal)
    Front wiper switch off
    Below 1 V
    Front wiper switch HI
    11 to 14 V
    E85-2 (W) - Body ground
    L - Body ground
    Front washer motor power source circuit
    Front washer switch off
    Below 1 V
    Front washer switch on
    11 to 14 V
    If the result is not as specified, the ECU may have a malfunction.


CHECK WINDSHIELD WIPER SWITCH
E161154E01
  1. Disconnect the E16 switch connector.

  2. Measure the voltage according to the value(s) in the table below.

    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    E16-2 (+B) - E16-10 (E)*1
    B - W-B
    Power source circuit (from battery)
    Engine switch on (IG)
    11 to 14 V
    E16-3 (+B) - E16-5 (E)*2
    B - W-B
    Power source circuit (from battery)
    Engine switch on (IG)
    11 to 14 V
    E16-10 (E) - Body ground*1
    W-B - Body ground
    Ground circuit
    Always
    Below 1 V
    E16-5 (E) - Body ground*2
    W-B - Body ground
    Ground circuit
    Always
    Below 1 V

    HINT:
    1. *1: for LH Side
    2. *2: for RH Side

    If the result is not as specified, there may be a malfunction on the wire harness side.


CHECK MAIN BODY ECU (COWL SIDE JUNCTION BLOCK LH)
C172609E03
  1. Disconnect the 2A, 2B, E3 and E1 main body ECU connectors.

  2. Measure the voltage according to the value(s) in the table below.

    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    E1-6 (AM1) - 2D-62 (GND2)
    W - W-B
    ECU power supply (from battery)
    Always
    11 to 14 V
    E2-11 (IG2D) - 2D-62 (GND2)
    B - W-B
    IG signal circuit
    Engine switch off
    Below 1 V
    Engine switch on (IG)
    11 to 14 V
    2B-22 (STP) - 2D-62 (GND2)
    R - W-B
    Stop light switch circuit
    Stop light switch off
    Below 1 V
    Stop light switch on
    11 to 14 V
    2D-62 (GND2) - Body ground
    W-B - Body ground
    Ground circuit
    Always
    Below 1 V
    If the result is not as specified, there may be a malfunction on the wire harness side.


CHECK MAP LIGHT
E157216E01
  1. Disconnect the R7 map light connector.

  2. Measure the voltage according to the value(s) in the table below.

    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    R7-15 (+B2) - R7-3 (GND4)
    B - W-B
    ECU power supply (from battery)
    Always
    11 to 14 V
    R7-14 (IG) - R7-3 (GND4)
    L - W-B
    IG signal circuit
    Engine switch off
    Below 1 V
    Engine switch on (IG)
    11 to 14 V
    R7-3 (GND4) - Body ground
    W-B - Body ground
    Ground circuit
    Always
    Below 1 V
    If the result is not as specified, there may be a malfunction on the wire harness side.


CHECK RAIN SENSOR
E139261E05
  1. Disconnect the R11 rain sensor connector.

  2. Measure the voltage according to the value(s) in the table below.

    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    R11-4 (SIG) - Body ground
    G - Body ground
    IG signal circuit (to IG relay)
    Engine switch off
    Below 1 V
    Engine switch on (IG)
    11 to 14 V
    R11-1 (ES) - Body ground
    W - Body ground
    Ground circuit
    Always
    Below 1 V
    If the result is not as specified, there may be a malfunction on the wire harness side.


CHECK HEADLIGHT CLEANER CONTROL RELAY
E139344
  1. Disconnect the relay connector.

  2. Measure the voltage according to the value(s) in the table below.

    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    3 (IG) - 4 (E)
    R-B - W-B
    IG signal circuit (to IG relay)
    Engine switch off
    Below 1 V
    Engine switch on (IG)
    11 to 14 V
    6 (PB) - 4 (E)
    W-G - W-B
    Headlight cleaner motor operation signal
    Headlight cleaner motor is stopped
    Below 1 V
    Headlight cleaner motor is operating
    11 to 14 V
    If the result is not as specified, there may be a malfunction on the wire harness side.

  3. Reconnect the relay connector.

  4. Measure the voltage according to the value(s) in the table below.

    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    2 (H) - 4 (E)
    LG - W-B
    Headlight cleaner switch and headlight switch operation signal
    Headlight cleaner switch is off
    Below 1 V
    Headlight switch is off
    Below 1 V
    Headlight cleaner switch and headlight switch is on
    11 to 14 V
    If the result is not as specified, the relay may have a malfunction.

← PROBLEM SYMPTOMS TABLE (from Jan 2012)TERMINALS OF ECU (from Jan 2012) →