TERMINALS OF ECU
System information · Vehicles built from Jan 2012
Versions by build date: Sep 2011 – Dec 2011 from Jan 2012
| CHECK WINDSHIELD WIPER ECU |


Disconnect the E83 and E85 ECU connectors.
Measure the voltage and resistance according to the value(s) in the table below.
If the result is not as specified, there may be a malfunction on the wire harness side.Terminal No. (Symbol)
Wiring Color
Terminal Description
Condition
Specified Condition
E83-5 (IG1l) - E85-10 (E)
G - W-B
IG signal circuit
Engine switch on (IG)
11 to 14 V
E85-10 (E) - Body ground
W-B - Body ground
Ground circuit
Always
Below 1 Ω
Reconnect the E83 and E85 ECU connectors.
Measure the voltage and waveform according to the value(s) in the table below.
Terminal No. (Symbol)
Wiring Color
Terminal Description
Condition
Specified Condition
E83-7 (+SM) - Body ground
W - Body ground
Front wiper motor operation signal
Front wiper is operated
11 to 14 V
Front wiper is stopped
Below 1 V
E83-8 (WIG) - Body ground
B - Body ground
Front wiper motor power source circuit
Engine switch off
Below 1 V
Engine switch on (IG)
11 to 14 V
E83-10 (1S) - Body ground
G - Body ground
Front wiper motor power supply circuit
Front wiper switch off
Below 1 V
Front wiper switch LO
11 to 14 V
E83-9 (2S) - Body ground
R - Body ground
Front wiper motor power supply circuit (HI signal)
Front wiper switch off
Below 1 V
Front wiper switch HI
11 to 14 V
E85-2 (W) - Body ground
L - Body ground
Front washer motor power source circuit
Front washer switch off
Below 1 V
Front washer switch on
11 to 14 V
E85-5 (CANL) - Body ground
R - Body ground
CAN communication signal
Engine switch on (IG)
Pulse generation
E85-6 (CANH) - Body ground
LG - Body ground
CAN communication signal
Engine switch on (IG)
Pulse generation
E85-7 (MPX1) - Body ground
R - Body ground
LIN communication signal
Engine switch on (IG)
Pulse generation
| CHECK WINDSHIELD WIPER SWITCH |


Disconnect the E16 switch connector.
Measure the voltage and resistance according to the value(s) in the table below.
Terminal No. (Symbol)
Wiring Color
Terminal Description
Condition
Specified Condition
E16-2 (+B) - E16-10 (E)*1
B - W-B
Power source circuit (from battery)
Engine switch on (IG)
11 to 14 V
E16-3 (+B) - E16-5 (E)*2
B - W-B
Power source circuit (from battery)
Engine switch on (IG)
11 to 14 V
E16-10 (E) - Body ground*1
W-B - Body ground
Ground circuit
Always
Below 1 Ω
E16-5 (E) - Body ground*2
W-B - Body ground
Ground circuit
Always
Below 1 Ω
- HINT:
- *1: for LH Side
- *2: for RH Side
- *1: for LH Side
| CHECK MAIN BODY ECU (COWL SIDE JUNCTION BLOCK LH) |


Disconnect the 2D, E2 and E1 main body ECU connectors.
Measure the voltage and resistance according to the value(s) in the table below.
Terminal No. (Symbol)
Wiring Color
Terminal Description
Condition
Specified Condition
E1-6 (AM1) - 2D-62 (GND2)
W - W-B
Power source circuit (from battery)
Always
11 to 14 V
E2-11 (IG2D) - 2D-62 (GND2)
B - W-B
IG signal circuit
Engine switch off
Below 1 V
Engine switch on (IG)
11 to 14 V
2B-22 (STP) - 2D-62 (GND2)
R - W-B
Stop light switch circuit
Stop light switch off
Below 1 V
Stop light switch on
11 to 14 V
2D-62 (GND2) - Body ground
W-B - Body ground
Ground circuit
Always
Below 1 Ω
Reconnect the 2D, E2 and E1 main body ECU connectors.
Measure the voltage and waveform according to the value(s) in the table below.
Terminal No. (Symbol)
Wiring Color
Terminal Description
Condition
Specified Condition
E2-13 (HDLO) - Body ground
L - Body ground
Headlight low beam operation signal
Engine switch on (IG)
Headlight dimmer switch in head
11 to 14 V
Engine switch on (IG)
Headlight dimmer switch not in head
Below 1 V
E3-15 (CANN) - Body ground
R - Body ground
CAN communication signal
Engine switch on (IG)
Pulse generation
E3-16 (CANP) - Body ground
GR - Body ground
CAN communication signal
Engine switch on (IG)
Pulse generation
| CHECK MAP LIGHT |


Disconnect the R7 map light connector.
Measure the voltage and resistance according to the value(s) in the table below.
Terminal No. (Symbol)
Wiring Color
Terminal Description
Condition
Specified Condition
R7-14 (IG) - R7-3 (GND5)
G - W-B
IG signal circuit
Engine switch off
Below 1 V
Engine switch on (IG)
11 to 14 V
R7-3 (GND5) - Body ground
W-B - Body ground
Ground circuit
Always
Below 1 Ω
| CHECK RAIN SENSOR |


Disconnect the R11 rain sensor connector.
Measure the voltage and resistance according to the value(s) in the table below.
Terminal No. (Symbol)
Wiring Color
Terminal Description
Condition
Specified Condition
R11-4 (SIG) - Body ground
G - Body ground
IG signal circuit
Engine switch off
Below 1 V
Engine switch on (IG)
11 to 14 V
R11-1 (ES) - Body ground
W - Body ground
Ground circuit
Always
Below 1 Ω
Reconnect the R11 rain sensor connector.
Measure the waveform according to the value(s) in the table below.
Terminal No. (Symbol)
Wiring Color
Terminal Description
Condition
Specified Condition
R11-3 (MPX) - Body ground
R - Body ground
LIN communication signal
Engine switch on (IG)
Pulse generation
| CHECK HEADLIGHT CLEANER CONTROL RELAY (w/ Headlight Cleaner System) |


- HINT:
- The headlight cleaner control relay uses waterproof connector. Therefore, voltage cannot be checked with the connector connected to the vehicle.
| Terminal No. (Symbol) |
Wiring Color |
Terminal Description |
Condition |
Specified Condition |
| 3 (IG) - 4 (E) |
- |
IG signal circuit |
Engine switch off |
Below 1 V |
| Engine switch on (IG) |
11 to 14 V |
|||
| 4 (E) - Body ground |
- |
Ground circuit |
Always |
Below 1 Ω |
| 6 (PB) - 4 (E) |
- |
Headlight cleaner motor operation signal |
Headlight cleaner motor is stopped |
11 to 14 V |
| Headlight cleaner motor is operating |
Below 1 V |
|||
| 2 (H) - 4 (E) |
- |
Headlight cleaner switch and headlight switch operation signal |
Engine switch on (IG) Headlight cleaner switch is off |
Below 1 V |
| Engine switch on (IG) Headlight switch is off |
Below 1 V |
|||
| Engine switch on (IG) Headlight cleaner switch is on and headlight dimmer switch in HEAD |
11 to 14 V |
|||
| 5 (FRWA) - 4 (E)* |
- |
Front washer switch operation signal |
Engine switch on (IG) Front washer switch is off |
11 to 14 V |
| Engine switch on (IG) Front washer switch is on |
Below 1 V |
|||
| 1 (HDLO) - 4 (E)* |
- |
Headlight low beam operation signal |
Engine switch on (IG) Headlight dimmer switch in HEAD |
11 to 14 V |
| Engine switch on (IG) Headlight dimmer switch not in HEAD |
Below 1 V |
- *: w/ Headlight Auto Leveling