2011-2013 Land Cruiser · Service Manual Vehicle Exterior

DATA LIST / ACTIVE TEST

System information · Vehicles built from Jan 2012

Versions by build date: Sep 2011 – Dec 2011 from Jan 2012


READ DATA LIST

HINT:
Using the intelligent tester to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.

NOTICE:
In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.

  1. Warm up the engine.

  2. Turn the engine switch off.

  3. Connect the intelligent tester to the DLC3.

  4. Turn the engine switch on (IG).

  5. Turn the intelligent tester on.

  6. Enter the following menus: Body / (desired system) / Data List.

  7. According to the display on the tester, read the "Data List".

    Combination Switch 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    F Wiper LO Switch
    Front wiper LO switch / ON or OFF
    ON: Front wiper switch in LO position
    OFF: Front wiper switch not in LO position
    -
    F Wiper HI Switch
    Front wiper HI switch / ON or OFF
    ON: Front wiper switch in HI position
    OFF: Front wiper switch not in HI position
    -
    F Wiper AUTO Switch
    Front wiper AUTO switch / ON or OFF
    ON: Front wiper switch in AUTO position
    OFF: Front wiper switch not in AUTO position
    -
    F Wiper MIST Switch
    Front wiper MIST switch / ON or OFF
    ON: Front wiper switch in MIST position
    OFF: Front wiper switch not in MIST position
    -
    F Washer Switch
    Front washer switch / ON or OFF
    ON: Front washer switch on
    OFF: Front washer switch off
    -
    IG Switch SIG
    Engine switch signal / ON or OFF
    ON: Engine switch on (IG)
    OFF: Engine switch off
    "OFF" is also displayed for this item when the engine switch is on (ACC).
    Rain Sensor 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Rain Sensor Cold
    Rain sensor cold / COLD or OK
    COLD: Front wiper switch in AUTO position
    OK: Front wiper switch not in AUTO position
    -
    Rain Sensor Hot
    Rain sensor cold / HOT or OK
    HOT: Front wiper switch in AUTO position
    OK: Front wiper switch not in AUTO position
    -
    Body No. 4 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Washer Level Switch
    Washer fluid level warning switch / ON or OFF
    ON: Washer jar and tank empty
    OFF: Washer jar and tank full
    -
    IG Switch SIG
    Engine switch signal / ON or OFF
    ON: Engine switch on (IG)
    OFF: Engine switch off
    "OFF" is also displayed for this item when the engine switch is on (ACC).
    Main Body 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Stop Light Switch
    Stop light switch signal / ON or OFF
    ON: Stop light switch on
    OFF: Stop light switch off
    -


PERFORM ACTIVE TEST

HINT:
Using the intelligent tester to perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.

NOTICE:
When a Body No. 5 (windshield wiper ECU) related front wiper switch is on, Active Test items related to the front wiper switch are prohibited (double operation prohibition). Check that the front wiper switches are off before performing Active Tests.

  1. Warm up the engine.

  2. Turn the engine switch off.

  3. Connect the intelligent tester to the DLC3.

  4. Turn the engine switch on (IG).

  5. Turn the intelligent tester on.

  6. Enter the following menus: Body / (desired system) / Active Test.

  7. According to the display on the tester. perform the "Active Test".

    Body No. 5 
    Tester Display
    Test Part
    Control Range
    Diagnostic Note
    Wiper Mot (HI)
    Wiper motor HI operation
    ON / OFF
    -
    Wiper Mot (LO)
    Wiper motor LO operation
    ON / OFF
    -
    Main Body 
    Tester Display
    Test Part
    Control Range
    Diagnostic Note
    Head Light Cleaner
    Headlight low beam signal
    ON / OFF
    -

← DATA LIST / ACTIVE TEST (Sep 2011 – Dec 2011)Washer Signal Circuit (from Jan 2012) →