2011-2013 Land Cruiser · Service Manual Vehicle Exterior

INSTALLATION

Removal / installation · Vehicles built from Jan 2012

Versions by build date: Sep 2011 – Dec 2011 from Jan 2012

HINT:
  1. Use the same procedure for LHD and RHD vehicles.
  2. The procedure listed below is for LHD vehicles.


1. INSTALL WINDSHIELD WIPER MOTOR ASSEMBLY

  1. E156196
    Install the wiper motor with the 2 screws.

    Torque:
    7.5 N*m{ 76 kgf*cm , 66 in.*lbf }

  1. Apply MP grease to the crank arm pivot of the windshield wiper motor assembly.

  1. E156194
    Install the wiper motor and link.

  1. E156195
    Install the wiper motor and link.

  1. E161961E01
    Install the wiper motor cover with the clamp.


2. INSTALL WINDSHIELD WIPER LINK ASSEMBLY

  1. B184646E01
    Install the windshield wiper motor and link assembly with the 3 bolts and the pin as shown in the illustration.

    Torque:
    7.0 N*m{ 71 kgf*cm , 62 in.*lbf }

  1. Connect the connector.


3. INSTALL COWL TOP VENTILATOR LOUVER SUB-ASSEMBLY

  1. E156191E01
    Push the ventilator louver in the direction indicated by the arrow in the illustration to attach the 17 claws and 2 clips and install the ventilator louver.


4. INSTALL HOOD TO COWL TOP SEAL

  1. E156189
    Attach the 12 clips and 4 clamps to install the hood to cowl top seal.

  1. E156188
    Install the washer hose.


5. INSTALL FRONT FENDER MAIN SEAL LH

  1. B181061
    Attach the 3 clips to install the fender main seal.


6. INSTALL FRONT FENDER MAIN SEAL RH

HINT:
Use the same procedure described for the LH side.


7. INSTALL UPPER RADIATOR SUPPORT SEAL

  1. Install the radiator support seal with the 7 clips.

    B180890E02


8. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

NOTICE:
When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).


9. INSTALL FRONT WIPER ARM LH

  1. E156199E01
    Stop the wiper motor at the automatic stop position.

  1. Clean the wiper pivot serration with a wire brush.

  1. E157802E01
    Install the wiper arm and blade with the nut. Make sure that the wiper arm and blade comes to the position shown in the illustration.

    Standard Measurement:
    Position
    Specified Condition
    A
    16.8 to 36.8 mm (0.661 to 1.45 in.)

    Torque:
    25 N*m{ 255 kgf*cm , 18 ft.*lbf }

    HINT:
    Hold down the wiper arm hinge with your hand while tightening the nut.


10. INSTALL FRONT WIPER ARM RH

  1. E156199E01
    Stop the wiper motor at the automatic stop position.

  1. Clean the wiper pivot serration with a wire brush.

  1. E157803E01
    Install the wiper arm and blade with the nut. Make sure that the wiper arm and blade comes to the position shown in the illustration.

    Standard Measurement:
    Position
    Specified Condition
    B
    20.0 to 40.0 mm (0.787 to 1.57 in.)

    Torque:
    25 N*m{ 255 kgf*cm , 18 ft.*lbf }

    HINT:
    Hold down the wiper arm hinge with your hand while tightening the nut.

  1. Operate the front wipers while spraying washer fluid on the windshield glass. Make sure that the front wipers function properly and there is no interference with the vehicle body.

← INSTALLATION (Sep 2011 – Dec 2011)COMPONENTS (from Sep 2011) →