B2799 Engine Immobiliser System Malfunction
Diagnostic trouble codes · Vehicles built from Jan 2012
Versions by build date: Sep 2011 – Dec 2011 from Jan 2012
DESCRIPTION
This DTC is output when one of the following occurs: 1) the ECM detected errors in its own communications with the ID code box (immobiliser code ECU); 2) the ECM detects errors in the communication lines; or 3) the ECU communication ID between the ID code box (immobiliser code ECU) and ECM is different and an engine start is attempted.Before troubleshooting for this DTC, make sure no certification ECU DTCs are stored. If stored, troubleshoot the certification ECU DTCs first.
| DTC Code |
DTC Detection Condition |
Trouble Area |
| B2799 |
One of following conditions is met:
|
|
WIRING DIAGRAM






INSPECTION PROCEDURE
| 1. CLEAR DTC |
Clear the DTCs (Click here).
| NEXT | |
| 2. CHECK FOR DTC |
Check for DTCs (Click here).
- OK:
- DTC B2799 is not output.
|
|
||||
| OK | ||
| ||
| 3. REREGISTER ECU CODE |
Reregister the recognition codes in the ECUs.
| NEXT | |
| 4. CLEAR DTC |
Clear the DTCs (Click here).
| NEXT | |
| 5. CHECK FOR DTC |
Check for DTCs (Click here).
- OK:
- DTC B2799 is not output.
|
|
||||
| OK | ||
| ||
| 6. CHECK CONNECTION OF CONNECTOR |
Turn the engine switch off.
Check that the connectors are properly connected to the ECM and the ID code box.
- OK:
- Connectors are properly connected.
|
|
||||
| OK | |
| 7. CHECK HARNESS AND CONNECTOR (ID CODE BOX (IMMOBILISER CODE ECU) - ECM) |
Disconnect the E28 ID code box connector.

Disconnect the A38*1 or A52*2 ECU connector.

- HINT:
- *1: for LHD
- *2: for RHD
- *1: for LHD
Measure the resistance according to the value(s) in the table below.
for 1UR-FE
- Standard Resistance:
Tester Connection
Condition
Specified Condition
E28-5 (EFII) - A38*1-29 (IMO)
Always
Below 1 Ω
E28-6 (EFIO) - A38*1-40 (IMI)
E28-5 (EFII) or A38*1-29 (IMO) - Body ground
Always
10 kΩ or higher
E28-6 (EFIO) or A38*1-40 (IMI) - Body ground
E28-5 (EFII) - A52*2-29 (IMO)
Always
Below 1 Ω
E28-6 (EFIO) - A52*2-40 (IMI)
E28-5 (EFII) or A52*2-29 (IMO) - Body ground
Always
10 kΩ or higher
E28-6 (EFIO) or A52*2-40 (IMI) - Body ground
- HINT:
- *1: for LHD
- *2: for RHD
- *1: for LHD
for 1GR-FE, 1VD-FTV
- Standard Resistance:
Tester Connection
Condition
Specified Condition
E28-5 (EFII) - A38*1-10 (IMO)
Always
Below 1 Ω
E28-6 (EFIO) - A38*1-11 (IMI)
E28-5 (EFII) or A38*1-10 (IMO) - Body ground
Always
10 kΩ or higher
E28-6 (EFIO) or A38*1-11 (IMI) - Body ground
E28-5 (EFII) - A52*2-10 (IMO)
Always
Below 1 Ω
E28-6 (EFIO) - A52*2-11 (IMI)
E28-5 (EFII) or A52*2-10 (IMO) - Body ground
Always
10 kΩ or higher
E28-6 (EFIO) or A52*2-11 (IMI) - Body ground
- HINT:
- *1: for LHD
- *2: for RHD
- *1: for LHD
for 3UR-FE
- Standard Resistance:
Tester Connection
Condition
Specified Condition
E28-5 (EFII) - A38-29 (IMO)
Always
Below 1 Ω
E28-6 (EFIO) - A38-40 (IMI)
E28-5 (EFII) or A38-29 (IMO) - Body ground
Always
10 kΩ or higher
E28-6 (EFIO) or A38-40 (IMI) - Body ground
|
|
||||
| OK | |
| 8. REPLACE ECM |
for 1GR-FE
Temporarily replace the ECM with a new one (Click here).
for 1UR-FE
Temporarily replace the ECM with a new one (Click here).
for 1VD-FTV
Temporarily replace the ECM with a new one (Click here).
for 3UR-FE
Temporarily replace the ECM with a new one (Click here).
| NEXT | |
| 9. REGISTER ECU CODE |
Register the recognition codes in the ECUs.
| NEXT | |
| 10. CLEAR DTC |
Clear the DTCs (Click here).
| NEXT | |
| 11. CHECK FOR DTC |
Check for DTCs (Click here).
- OK:
- DTC B2799 is not output.
|
|
||||
| OK | ||
| ||
