2011-2013 Land Cruiser · Service Manual Vehicle Exterior

DISASSEMBLY

Removal / installation · Vehicles built Sep 2011 – Dec 2011

Versions by build date: Sep 2011 – Dec 2011 from Jan 2012

HINT:
  1. Use the same procedures for the RH side and LH side.
  2. The procedures listed below are for the LH side.


1. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

CAUTION:
Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

NOTICE:
When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).


2. REMOVE FRONT LOWER DOOR FRAME BRACKET GARNISH LH

  1. B180820
    Detach the clip and claw, remove the front lower door frame bracket garnish.


3. REMOVE FRONT DOOR INSIDE HANDLE BEZEL LH

  1. B180816
    Using a screwdriver, detach the 4 claws and remove the inside handle bezel.

    HINT:
    Tape the screwdriver tip before use.


4. REMOVE FRONT DOOR ARMREST BASE PANEL ASSEMBLY LH

B180817
  1. Using a moulding remover, detach the 5 claws.

  1. Disconnect the connector and remove the armrest base panel.


5. REMOVE MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY

  1. B182892
    Remove the 3 screws and master switch.


6. REMOVE DOOR ASSIST GRIP COVER LH

  1. B180819
    Using a moulding remover, detach the 8 claws and remove the door assist grip cover.


7. REMOVE FRONT DOOR TRIM BOARD SUB-ASSEMBLY LH

  1. B180821
    Remove the 3 screws.

  1. Remove the 13 clips, 4 claws and trim board.

  1. Disconnect the connector.

  1. B180822
    Disconnect the 2 cables from the inside handle.


8. REMOVE COURTESY LIGHT ASSEMBLY (w/ Courtesy Light)

  1. E155940
    Detach the claw.

  1. Remove the courtesy light and then disconnect the connector.


9. REMOVE SEAT MEMORY SWITCH (w/ Seat Position Memory System)

B180823
  1. Disconnect the connector.

  1. Remove the screw and seat memory switch.


10. REMOVE FRONT DOOR INSIDE HANDLE SUB-ASSEMBLY LH

  1. B235654
    Detach the 2 claws and remove the inside handle.


11. REMOVE FRONT DOOR INSIDE HANDLE BEZEL LH

  1. B235655
    Remove the 7 screws and front door inside handle bezel.


12. REMOVE OUTER REAR VIEW MIRROR ASSEMBLY LH

B180573E01
  1. w/ Power Mirror Control System:

    1. Disconnect the connector labeled A.

    2. Detach the clamp.

  1. Remove the 3 nuts and claw.

  1. Remove the outer rear view mirror.


13. REMOVE OUTER MIRROR CONTROL ECU ASSEMBLY (w/ Retract Mirror)

B180824
  1. Disconnect the 2 connectors.

  1. Remove the 2 screws and outer mirror control ECU.


14. REMOVE FRONT DOOR PANEL CUSHION

  1. B180835
    Remove the screw and front door panel cushion.


15. REMOVE FRONT NO. 1 SPEAKER ASSEMBLY
  1. Disconnect the speaker connector.

  1. B181519
    Remove the 4 screws and speaker.

    NOTICE:
    Do not touch the cone part of the speaker.


16. REMOVE SIDE AIRBAG SENSOR ASSEMBLY LH

  1. B181765
    Disconnect the connector.

  1. Remove the bolt and side airbag sensor.


17. REMOVE FRONT DOOR SERVICE HOLE COVER LH

  1. B182874
    Using a clip remover, detach the 9 clamps.

  1. Remove the bolt and disconnect the 2 connectors.

  1. Remove the service hole cover.

    HINT:
    Remove the remaining tape on the door.


18. REMOVE FRONT INNER DOOR GLASS WEATHERSTRIP LH

  1. B180828
    Detach the 4 claws by pulling the weatherstrip upward to remove the weatherstrip.


19. REMOVE FRONT DOOR GLASS SUB-ASSEMBLY LH
  1. Driver Side:
    Temporarily install the multiplex network master switch.

  1. Passenger Side:
    Temporarily install the power window regulator switch assembly.

  1. Connect the cable to the negative (-) battery terminal.

  1. Move the door glass until the bolts appear in the service holes.

  1. Disconnect the cable from the negative (-) battery terminal.

    NOTICE:
    When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).

  1. B180832
    Remove the 2 bolts.

    NOTICE:
    Be careful when removing the bolts as the glass may fall and become damaged.

  1. B180833
    Remove the door glass in the direction indicated by the arrows in the illustration.

    HINT:
    Remove the glass upward.

    NOTICE:
    Be careful not to damage the glass.

  1. Driver Side:
    Remove the multiplex network master switch.

  1. Passenger Side:
    Remove the power window regulator switch assembly.


20. REMOVE FRONT DOOR GLASS RUN LH

  1. B180838
    Remove the front door glass run.


21. REMOVE FRONT DOOR REAR LOWER FRAME SUB-ASSEMBLY LH

  1. B180840
    Remove the bolt and rear lower frame.


22. REMOVE LOWER DOOR FRAME GARNISH LH

  1. B180839
    Detach the claw and remove the lower door frame garnish.


23. REMOVE FRONT DOOR BELT MOULDING SUB-ASSEMBLY LH

B182606E01
  1. Put protective tape around the belt moulding.

  1. B182604
    Detach the claw and remove the belt moulding.


24. REMOVE FRONT DOOR REAR WINDOW FRAME MOULDING LH

B182608E01
  1. Put protective tape around the window frame moulding.

  1. Detach the clip and remove the double-sided tape to remove the window frame moulding.


25. REMOVE FRONT DOOR WINDOW REGULATOR SUB-ASSEMBLY LH

  1. B180836E03
    Loosen the temporary bolt.
    Text in Illustration 
    *1
    Temporary Bolt

  1. Remove the 5 bolts, and window regulator.

    HINT:
    Remove the window regulator through the service hole.

    NOTICE:
    Be careful when removing the bolts as the window regulator may fall and become damaged.

  1. Remove the front door window regulator sub-assembly and the front power window regulator motor assembly as a unit.

  1. Remove the temporary bolt from the front door window regulator sub-assembly.


26. REMOVE FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY LH

  1. B294158E01
    Using a T25 "TORX" driver, remove the 3 screws and motor.

    NOTICE:
    Be careful when removing the screws as the motor may fall and become damaged.

    Text in Illustration 
    *A
    for Models with Jam Protection Function on 4 Windows
    *B
    for Front Passenger Side, for Models with Jam Protection Function on Driver Door Window Only


27. REMOVE FRONT DOOR OUTSIDE HANDLE COVER LH

  1. B180841
    Remove the hole plug.

  1. Using a T30 "TORX" wrench, loosen the screw and remove the cover with the door lock cylinder installed.

  1. B180845
    Detach the 2 claws and remove the front door outside handle cover.


28. REMOVE FRONT DOOR HANDLE ASSEMBLY OUTSIDE LH

  1. B180849
    Disconnect the connector.

  1. Using a T30 "TORX" wrench, loosen the screw.

  1. B180848
    Remove the handle by sliding and pulling it in the direction indicated by the arrow in the illustration.

    NOTICE:
    If the release plate is not pulled and held when removing the handle, the release plate will interfere with the handle and become damaged.


29. REMOVE FRONT DOOR FRONT OUTSIDE HANDLE PAD LH

  1. B180857
    Detach the 3 claws and remove the pad.


30. REMOVE FRONT DOOR REAR OUTSIDE HANDLE PAD LH

  1. B180858
    Detach the 2 claws and remove the pad.


31. REMOVE FRONT DOOR LOCK ASSEMBLY LH

  1. B180842
    Using a T30 "TORX" wrench, remove the 3 screws.

    HINT:
    Remove the door lock through the service hole.

    NOTICE:
    Be careful when removing the screws as the door lock may fall and become damaged.


32. REMOVE FRONT DOOR LOCK REMOTE CONTROL CABLE ASSEMBLY LH

  1. B180843
    Remove the front door lock remote control cable assembly.


33. REMOVE FRONT DOOR INSIDE LOCKING CABLE ASSEMBLY LH

  1. B180846
    Using a screwdriver, detach the 3 claws.

    HINT:
    Tape the screwdriver tip before use.

  1. B180847
    Remove the front door inside locking cable assembly.


34. REMOVE FRONT DOOR OUTSIDE HANDLE FRAME SUB-ASSEMBLY LH

  1. B180851
    Using a T30 "TORX" wrench, loosen the screw.

  1. B182884
    Detach the 2 claws. Slide the outside handle frame and No. 2 electrical key wire harness to remove it.

    HINT:
    Remove the outside handle frame through the service hole.

  1. Remove the lock open rod from the outside handle frame.


35. REMOVE NO. 2 ELECTRICAL KEY WIRE HARNESS

  1. B180850
    Disconnect the connector.

  1. Detach the 3 clamps and remove the wire harness from the frame.


36. REMOVE FRONT DOOR LOCK OPEN ROD LH

  1. B180852
    Remove the front door lock open rod.


37. REMOVE DOOR ELECTRICAL KEY OSCILLATOR

  1. B180853
    Remove the screw and door electrical key oscillator.


38. REMOVE FRONT NO. 2 DOOR STIFFENER CUSHION

  1. B183088
    Remove the 2 bolts.

  1. Detach the 2 clamps and door stiffener cushion.


39. REMOVE FRONT DOOR CHECK COVER LH

  1. B180856
    Remove the cover.


40. REMOVE FRONT DOOR CHECK ASSEMBLY LH

B155785
  1. Remove the bolt, 2 nuts and door check.

    HINT:
    Remove the door check through the service hole.

    NOTICE:
    Be careful when removing the bolt and nuts as the door check may fall and become damaged.


41. REMOVE FRONT DOOR WEATHERSTRIP LH

  1. B180855
    Using a clip remover, detach the 21 clips and remove the weatherstrip.

    HINT:
    If clips are damaged during removal, replace them.

← COMPONENTS (from Jan 2012)DISASSEMBLY (from Jan 2012) →