2011-2013 Land Cruiser · Service Manual Power Source / Network

U0122 Lost Communication with Vehicle Dynamics Control Module

Diagnostic trouble codes · Vehicles built Sep 2011 – Dec 2011

Also covers:

DESCRIPTION

If 2 or more DTCs are output during the DTC check, one side of the CAN branch wire may be open (One side of the CANH [branch wire]/CANL [branch wire] of the ECU and/or sensor is open).
DTC Code
DTC Detection Condition
Trouble Area
U0122
There is no communication from the skid control ECU.
  1. Power source circuit of skid control ECU
  2. One side of CAN branch wire of other systems
  3. Skid control ECU
  4. Skid control ECU branch wire or connector
U0129
There is no communication from the skid control ECU.
  1. Power source circuit of skid control ECU
  2. One side of CAN branch wire of other systems
  3. Skid control ECU
  4. Skid control ECU branch wire or connector

WIRING DIAGRAM

C176041E02

INSPECTION PROCEDURE


1. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
  1. Disconnect the cable from the negative (-) battery terminal before measuring the resistances of the main wire and the branch wire.

    CAUTION:
    For vehicles with an SRS system:
    Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

    NOTICE:
    When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).


NEXT


2. CHECK FOR OPEN IN CAN BUS WIRE (SKID CONTROL ECU BRANCH WIRE)

  1. C172533E01
    Disconnect the A24 skid control ECU connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    A24-11 (CANH) - A24-25 (CANL)
    Ignition switch off
    54 to 69 Ω



NG
REPAIR OR REPLACE SKID CONTROL ECU BRANCH WIRE OR CONNECTOR (CANH, CANL)
OK


3. CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU - BATTERY AND BODY GROUND)
  1. Connect the cable to the negative (-) battery terminal.

    NOTICE:
    When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).

  1. C172532E01
    Disconnect the A24 and A25 skid control ECU connectors.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    A24-1 (GND1) - Body ground
    Always
    Below 1 Ω
    A24-32 (GND2) - Body ground
    Always
    Below 1 Ω
    A25-4 (GND3) - Body ground
    Always
    Below 1 Ω

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    A24-2 (+BM1) - Body ground
    Always
    11 to 14 V
    A24-31 (+BS) - Body ground
    Always
    11 to 14 V
    A25-2 (+BM2) - Body ground
    Always
    11 to 14 V
    A24-46 (IG1) - Body ground
    Ignition switch ON
    11 to 14 V
    A25-1 (IG2) - Body ground
    Ignition switch ON
    11 to 14 V



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE MASTER CYLINDER SOLENOID (SKID CONTROL ECU) (Click here)


← U0114/38 Lost Communication with 4WD Control ECU (from Jan 2012)U0123 Lost Communication with Yaw Rate Sensor Module (+ U0124) (Sep 2011 – Dec 2011) →