2011-2013 Land Cruiser · Service Manual Audio / Visual / Telematics

Microphone Circuit between Microphone and Radio Receiver

Circuit diagnosis · Vehicles built from Jan 2012

DESCRIPTION

Using this circuit, the multi-media module receiver assembly sends power to the map light assembly (telephone microphone assembly), and the map light assembly sends microphone signals to the multi-media module receiver assembly.

WIRING DIAGRAM

E248564E01

INSPECTION PROCEDURE


1. CHECK HARNESS AND CONNECTOR (MULTI-MEDIA MODULE RECEIVER ASSEMBLY - MAP LIGHT ASSEMBLY)
  1. Disconnect the F77 multi-media module receiver assembly connector.

  1. Disconnect the R7 map light assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    F77-49 (SNS2) - R7-20 (SNS2)
    Always
    Below 1 Ω
    F77-29 (MACC) - R7-25 (ACC)
    Always
    Below 1 Ω
    F77-27 (MIN+) - R7-27 (MI1+)
    Always
    Below 1 Ω
    F77-48 (MIN-) - R7-26 (MIC-)
    Always
    Below 1 Ω
    F77-49 (SNS2) - Body ground
    Always
    10 kΩ or higher
    F77-29 (MACC) - Body ground
    Always
    10 kΩ or higher
    F77-27 (MIN+) - Body ground
    Always
    10 kΩ or higher
    F77-48 (MIN-) - Body ground
    Always
    10 kΩ or higher
    F77-28 (SGND) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


2. CHECK MULTI-MEDIA MODULE RECEIVER ASSEMBLY
  1. Reconnect the multi-media module receiver assembly connector.

  1. E239014E07
    Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    F77-28 (SGND) - Body ground
    Always
    Below 1 Ω
    F77-48 (MIN-) - Body ground
    Always
    Below 1 Ω

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    F77-29 (MACC) - Body ground
    Engine switch on (ACC)
    4 to 6 V

Text in Illustration 
*a
Component with harness connected
(Multi-media Module Receiver Assembly)


NG
Go to step 3
OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE (Click here)

3. INSPECT MAP LIGHT ASSEMBLY

  1. E248565E01
    Remove the map light assembly (Click here).

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    26 (MIC-) - 20 (SNS2)
    Always
    Below 1 Ω

    Text in Illustration 
    *a
    Component without harness connected
    (Map Light Assembly)



NG
Go to step 5
OK


4. CHECK MAP LIGHT ASSEMBLY
  1. Reconnect the multi-media module receiver assembly connector.

  1. E248566E01
    Reconnect the map light assembly connector.

  1. Turn the engine switch on (ACC).

  1. Connect an oscilloscope to terminals R7-27 (MI1+) and R7-26 (MIC-) of the map light assembly connector.

  1. Check the waveform of the telephone microphone assembly using the oscilloscope.

    Text in Illustration 
    *a
    Component with harness connected
    (Map Light Assembly)
    Result 
    Result
    Proceed to
    A waveform synchronized with the voice input to the map light assembly is not output.
    A
    A waveform synchronized with the voice input to the map light assembly is output.
    B



B
PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE (Click here)
A


5. CHECK TELEPHONE MICROPHONE ASSEMBLY
  1. Replace the telephone microphone assembly with a new or normally functioning one (Click here).

  1. Check if the same malfunction recurs.

    Result 
    Result
    Proceed to
    Malfunction does not recur
    (returns to normal).
    A
    Malfunction recurs.
    B



B
REPLACE MAP LIGHT ASSEMBLY (Click here)
A

END (TELEPHONE MICROPHONE ASSEMBLY IS DEFECTIVE)


← Display Signal Circuit between Multi-display and Radio Receiver (from Jan 2012)Visual Mute Signal Circuit between Radio Receiver and Multi-display (from Jan 2012) →