REPLACEMENT
Removal / installation · Vehicles built from Sep 2011
| 1. REPLACE INTAKE VALVE GUIDE BUSH |
Heat the cylinder head to approximately 80 to 100°C (176 to 212°F).
Place the cylinder head on wooden blocks.
Using SST and a hammer, tap out the valve guide bush.

- SST
- 09201-10000
(09201-01050)
09950-70010 (09951-07100)
Using a caliper gauge, measure the bush bore diameter of the cylinder head side.
- Standard bush bore diameter:
- 10.285 to 10.306 mm (0.405 to 0.406 in.)
If the bush bore diameter of the cylinder head is 10.356 mm (0.408 in.) or more, replace the cylinder head.
Select a new guide bush (STD or O/S 0.05), and measure its diameter.
Machine the bush bore diameter of the cylinder head side to the diameter of the selected guide bush.
- Bush Bore Diameter:
Bush Size
Specified Condition
STD
10.333 to 10.344 mm (0.4068 to 0.4072 in.)
O/S 0.05
10.383 to 10.394 mm (0.4088 to 0.4092 in.)
- Standard bush length:
- 41.3 to 41.7 mm (1.63 to 1.64 in.)
Using SST and a hammer, tap in a new guide bush to the standard protrusion height.

- SST
- 09201-10000
(09201-01050)
09950-70010 (09951-07100)
- Standard protrusion height:
- 14.3 to 14.7 mm (0.563 to 0.579 in.)
Text in Illustration *1
Height
Using a sharp 5.5 mm reamer, ream the guide bush to obtain the standard oil clearance between the guide bush and valve stem.

- Standard oil clearance:
- 0.025 to 0.060 mm (0.000984 to 0.00236 in.)
| 2. REPLACE EXHAUST VALVE GUIDE BUSH |
Heat the cylinder head to approximately 80 to 100°C (176 to 212°F).
Place the cylinder head on wooden blocks.
Using SST and a hammer, tap out the valve guide bush.

- SST
- 09201-10000
(09201-01050)
09950-70010 (09951-07100)
Using a caliper gauge, measure the bush bore diameter of the cylinder head.
- Standard bush bore diameter:
- 10.285 to 10.306 mm (0.405 to 0.406 in.)
If the bush bore diameter of the cylinder head is 10.356 mm (0.408 in.) or more, replace the cylinder head.
Select a new guide bush (STD or O/S 0.05), and measure its diameter.
Machine the bush bore diameter of the cylinder head side to the diameter of the selected guide bush.
- Bush Bore Diameter:
Bush Size
Specified Condition
STD
10.333 to 10.344 mm (0.4068 to 0.4072 in.)
O/S 0.05
10.383 to 10.394 mm (0.4088 to 0.4092 in.)
- Standard bush length:
- 46.8 to 47.2 mm (1.84 to 1.86 in.)
Using SST and a hammer, tap in a new guide bush to the standard protrusion height.

- SST
- 09201-10000
(09201-01050)
09950-70010 (09951-07100)
- Standard protrusion height:
- 14.3 to 14.7 mm (0.563 to 0.579 in.)
Text in Illustration *1
Height
Using a sharp 5.5 mm reamer, ream the guide bush to obtain the standard oil clearance between the guide bush and valve stem.

- Standard oil clearance:
- 0.030 to 0.065 mm (0.00118 to 0.00256 in.)
| 3. REPLACE SPARK PLUG TUBE |
- HINT:
- When using a new cylinder head, the spark plug tubes must be replaced.
Remove the spark plug tube.
Apply adhesive to the end of a new spark plug tube.

- Adhesive:
- Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent.
- Standard seal diameter:
- 15 mm (0.591 in.)
Text in Illustration *1
Adhesive
- NOTICE:
- Install the spark plug tube within 3 minutes after applying adhesive.
- Be careful not to deform the spark plug tube.
- Be careful not to expose the seal to coolant for at least 1 hour after installing it.
- Install the spark plug tube within 3 minutes after applying adhesive.
Using a wooden block and hammer, tap in the spark plug tube to the specified protrusion height.

- Standard protrusion height:
- 75.1 to 76.1 mm (2.96 to 3.00 in.)
Text in Illustration *1
Cylinder Head Top Surface
*a
75.1 to 76.1 mm
- NOTICE:
- To avoid tapping in the spark plug tube too far, measure the protrusion height while tapping it.
| 4. REPLACE RING PIN |
- NOTICE:
- It is not necessary to remove the ring pin unless it is being replaced.
Remove the ring pins.
Using a plastic-faced hammer, tap in new ring pins to the cylinder head.
- Standard Protrusion:
Item
Specified Condition
Ring pin A
5.5 to 6.5 mm (0.217 to 0.256 in.)
Ring pin B
3.5 to 6.5 mm (0.138 to 0.256 in.)


Text in Illustration *A
for Bank 1
*B
for Bank 2
*a
5.5 to 6.5 mm
*b
3.5 to 6.5 mm
