2011-2013 Land Cruiser · Service Manual Engine / Hybrid / EV System

REASSEMBLY

Removal / installation · Vehicles built from Sep 2011


1. INSTALL STUD BOLT

NOTICE:
If the stud bolt is deformed or its threads are damaged, replace it.

  1. Using E7 and E8 "TORX" socket wrenches, install the stud bolts.

    Torque:
    for stud bolts A, B, C and D:
    9.0 N*m{ 92 kgf*cm , 80 in.*lbf }


    A174172E02
    Text in Illustration 
    *A
    LH for Intake Side
    *B
    LH for Exhaust Side
    *C
    LH for Front Side
    *D
    RH for Intake Side
    *E
    RH for Exhaust Side
    *F
    RH for Front Side


2. INSTALL NO. 2 STRAIGHT SCREW PLUG

A174133E03

NOTICE:
If water leaks from the No. 2 straight screw plug or the plug is corroded, replace it.

  1. Using a 14 mm hexagon wrench, install 2 new gaskets and the 2 straight screw plugs.

    Torque:
    85 N*m{ 867 kgf*cm , 63 ft.*lbf }

    Text in Illustration 
    *A
    LH
    *B
    RH


3. INSTALL NO. 1 STRAIGHT SCREW PLUG

A174132E03

NOTICE:
If water leaks from the No. 1 straight screw plug or the plug is corroded, replace it.

  1. Using a 10 mm hexagon wrench, install 6 new gaskets and the 6 straight screw plugs.

    Torque:
    44 N*m{ 449 kgf*cm , 32 ft.*lbf }

    Text in Illustration 
    *A
    LH
    *B
    RH


4. INSTALL VALVE SPRING SEAT
  1. Install the valve spring seats to the cylinder head.


5. INSTALL VALVE STEM OIL SEAL

  1. A094934E18
    Apply a light coat of engine oil to new oil seals.
    Text in Illustration 
    *A
    Intake Side
    *B
    Exhaust Side
    *1
    Brown
    *2
    Gray

    NOTICE:
    Pay attention when installing the intake and exhaust oil seals. For example, installing the intake oil seal into the exhaust side or installing the exhaust oil seal into the intake side can cause installation problems later.

    HINT:
    The intake valve oil seals are brown and the exhaust valve oil seals are gray.

  1. A165065E04
    Using SST, push in the oil seals.
    SST
    09201-41020  
    Text in Illustration 
    *a
    CORRECT
    *b
    INCORRECT

    NOTICE:
    Failure to use SST will cause the seal to be damaged or improperly seated.


6. INSTALL INTAKE VALVE

  1. A094935E32
    Apply plenty of engine oil to the tip area of the intake valve shown in the illustration.

  1. Install the valve, compression spring and spring retainer to the cylinder head.

    Text in Illustration 
    *a
    40 mm (1.57 in.) or more

    NOTICE:
    Install the same parts in the same combination to their original locations.

  1. A164326E01
    Using SST and wooden blocks, compress the spring and install the retainer locks.
    SST
    09202-70020   (09202-00010)

  1. A165066
    Using a plastic-faced hammer, lightly tap the valve stem tip to ensure a proper fit.

    NOTICE:
    Be careful not to damage the retainer.


7. INSTALL EXHAUST VALVE

  1. A094936E30
    Apply plenty of engine oil to the tip area of the exhaust valve shown in the illustration.

  1. Install the valve, compression spring and spring retainer to the cylinder head.

    Text in Illustration 
    *a
    40 mm (1.57 in.) or more

    NOTICE:
    Install the same parts in the same combination to their original locations.

  1. A164327E01
    Using SST and wooden blocks, compress the spring and install the retainer locks.
    SST
    09202-70020   (09202-00010)

  1. A165067
    Using a plastic-faced hammer, lightly tap the valve stem tip to ensure a proper fit.

    NOTICE:
    Be careful not to damage the retainer.

← REPLACEMENT (from Sep 2011)REPAIR (from Sep 2011) →