2011-2013 Land Cruiser · Service Manual Vehicle Exterior

Wiper and Washer Switch Circuit

Circuit diagnosis · Vehicles built from Jan 2012

Versions by build date: Sep 2011 – Dec 2011 from Jan 2012

DESCRIPTION

This circuit provides power to operate the windshield wiper switch. The manual operation signals are sent to the windshield wiper ECU.

WIRING DIAGRAM

E158177E01

INSPECTION PROCEDURE


1. INSPECT FUSE (ECU-IG No. 1)
  1. Remove the ECU-IG No. 1 fuse from the cowl side junction block LH.

  1. Measure the resistance according to the value in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    ECU-IG No. 1 fuse
    Always
    Below 1 Ω



NG
REPLACE FUSE
OK


2. READ VALUE USING INTELLIGENT TESTER (WINDSHIELD WIPER SWITCH)
  1. Check the Data List for proper functioning of the windshield wiper switch.

    Combination Switch 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    F Wiper LO SW
    Front wiper LO switch / ON or OFF
    ON: Front wiper switch in LO
    OFF: Front wiper switch not in LO
    -
    F Wiper HI SW
    Front wiper HI switch / ON or OFF
    ON: Front wiper switch in HI
    OFF: Front wiper switch not in HI
    -
    F Wiper AUTO SW
    Front wiper AUTO switch / ON or OFF
    ON: Front wiper switch in AUTO
    OFF: Front wiper switch not in AUTO
    -
    F Wiper MIST SW
    Front wiper MIST switch / ON or OFF
    ON: Front wiper switch in MIST
    OFF: Front wiper switch not in MIST
    -
    F Washer SW
    Front washer switch / ON or OFF
    ON: Front washer switch on
    OFF: Front washer switch off
    -

    OK:
    The display is as specified in the normal condition.



NG
Go to step 3
OK

PROCEED TO NEXT CIRCUIT INSPECTION SHOWN IN PROBLEM SYMPTOMS TABLE (Click here)

3. CHECK HARNESS AND CONNECTOR (WINDSHIELD WIPER SWITCH - BATTERY AND BODY GROUND)

  1. E157240E02
    Disconnect the E16 switch connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    for LH Side 
    Tester Connection
    Switch Condition
    Specified Condition
    E16-2 (+B) - Body ground
    Engine switch on (IG)
    11 to 14 V
    E16-2 (+B) - Body ground
    Engine switch off
    Below 1 V
    for RH Side 
    Tester Connection
    Switch Condition
    Specified Condition
    E16-3 (+B) - Body ground
    Engine switch on (IG)
    11 to 14 V
    E16-3 (B) - Body ground
    Engine switch off
    Below 1 V

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    for LH Side 
    Tester Connection
    Condition
    Specified Condition
    E16-10 (E) - Body ground
    Always
    Below 1 Ω
    for RH Side 
    Tester Connection
    Condition
    Specified Condition
    E16-5 (E) - Body ground
    Always
    Below 1 Ω



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE WINDSHIELD WIPER SWITCH ASSEMBLY (Click here)


← Wiper and Washer Switch Circuit (Sep 2011 – Dec 2011)Rain Sensor Circuit (Sep 2011 – Dec 2011) →